Question about 1988 Dodge Ram Wagon

1 Answer

1988 dodge ram 150 pickup 4x4

Could you tell me where the fuses are located. I think the fuse for the fuel pump is blown or the fuel pump itself

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know the location of the inertia switch on a 1989 dodge ram 150 pickup truck


there is no inertia switch only ford uses them check for power to the pump if its there replace the pump if not check fuses and relays

Feb 25, 2014 | 1992 Dodge Ram 150 Club Cab

1 Answer

(correcting question) where is the fuse located for a 88 dodge dakota 4x4 V6


In the fuse block. Remove each fuse 1 by 1 and replace until you find the blown one.

Dec 04, 2013 | Cars & Trucks

1 Answer

Need to find were fuel pump is on 1988 dodge power ram 150


The fuel pump is in the gas tank. You'l need to drop the tank to replace the pump.

Jul 11, 2011 | 1988 Dodge D-Series Pickups

1 Answer

No power to fuel pump 1989 f150 5.8 eng.


Fuse is blown or the fuel pump relay is defective. This is assuming all wiring to the pump is good. Are you sure the pump itself has not just failed? After all this is a 22 year old vehicle and if the pump has never been replaced I would bet it has failed.

Aug 16, 2010 | 1988 Ford F 150

1 Answer

Fuel pump quit working, could it be a blown fuse?


Yes & no
Down load a service manual for your vehicle from this website

It will describe where everything is and how things work correctly

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

May 02, 2010 | 1988 Toyota Pickup

1 Answer

The dome light will not go out on my dodge ram 150


On the door jam is a button on both sides. One might have a short in it. Try unplugging them one at a time. They may just pull out or you will have to access them from the back

Jul 17, 2009 | 1988 Dodge D-Series Pickups

1 Answer

1988 ford truck f-150 xlt lariat cant get current to fuel pump


Have you checked the 'inertia switch' which in the event of an accident shuts off the fuel supply to prevent a fire . It's usually located in the cab on pass. side. Some models have one reset button, some 2 which have to be pressed at the same time. If that's not it, here's how the power to the pump SHOULD work, you will have to follow the path to see where it stops. When you turn the key on it turns on the EEC power relay on, this relay then provides power to the PCM (power control module) and the control side of the fuel pump relay. Power for the fuel pump is supplied through a fuse link or high current fuse attached to the starter solenoid (battery side). From the fuse link or high current fuse current flows thru the fuel pump relay and inertia switch to the fuel pump. The fuel pump relay is controlled by the PCM. When the ignition switch is turned on the fuel pump will operate, if the switch is NOT turned to start position, the PCM will shut off the fuel pump off after 1 second. This is to avoid flooding the engine when it is not running, just key on. So check out to see if you have a fuse link or a high current fuse and if they are blown.

Apr 14, 2009 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...