Question about 2008 GMC Yukon

1 Answer

I can not get my yukon battery out cables are removed but it seems to be bolted on???

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 203 Answers

If there s no visible straps look down the side there is normally a small plate that grips the battery low down on 1 or both sides. joe

Posted on Dec 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the positive battery cable


I don't exactly understand the question. You just undo the bolt through the terminal and it will lift off, if stuck just give it a twist. The other end of the cable is connected to the starter. this may be a bit hard to get to. Undo the negative cable before you do any of this so that you do not get any shorts. Put the negative terminal on last. this is for safety.

Nov 27, 2011 | 2007 GMC Yukon XL Denali

1 Answer

Where is the starter on a 1999 gmc yukon


As a last resort...trace the positive side cable from your battery...this connects to the starter...you will need to be under your Yukon to see the connection...the starter is usually help on with 3 long bolts...be sure to disconnect the battery before servicing the starter. Hope this helps.

Nov 10, 2011 | 1999 GMC Yukon

1 Answer

How do you remove the cover of the heater motor on a 1997 GMC yukon


Remove or disconnect:
Negative battery cable.
Instrument panel (I/P) compartment.
Front screw from right door sill plate.
Right hinge pillar trim panel.
Electrical connectors from ECM, as necessary.
Electrical connectors from blower motor, as necessary.
Bolt from right lower I/P support.
Blower motor cover.
Blower motor cooling tube.
Blower motor flange screws.
Blower motor.

Dec 04, 2010 | 1997 GMC Yukon

1 Answer

How to install a 1999 yukon ac compressor


Hi.

Follow below...

jshreader_20.jpg

REMOVAL PROCEDURE

CAUTION: Refer to Battery Disconnect Caution in Cautions and Notices.

1. Disconnect the negative battery cable.
2. Recover the refrigerant.
3. Remove the drive belt.
4. Disconnect the refrigerant hose assembly from the compressor.
5. Cap or plug all of the open connections.
6. Disconnect the electrical connectors, as necessary.
7. Remove the bolts.
8. Remove the compressor from the bracket.
9. Drain the compressor oil.
10. Measure the compressor oil. Refer to Adding Oil .

INSTALLATION PROCEDURE

1. Fill the compressor with oil. Refer to Adding Oil .
2. Install the compressor to the bracket.

NOTE : Refer to Fastener Notice in Cautions and Notices.

3. Install the compressor mounting bolts.

Tighten
Tighten the bolts to 50 N.m (37 lb ft) .

4. Connect the electrical connectors, as necessary.
5. Install the refrigerant hose assembly to the compressor.
6. Install the drive belt.
7. Connect the negative battery cable.
8. Charge the system. Refer to Refrigerant Recovery and Recycling, Adding Oil, Evacuating and Recharging Procedures .
9. Inspect the system for leaks.

I hope this helps.

Thanks...

Dec 03, 2010 | 1999 GMC Yukon

2 Answers

How to replace my dashboard


Very long process. Remove ground cable on battery first. Then take all screws out accross dash near windshield. thenremove all bolts to steering column and lower, remove all bolts on lower dash and braces, this will allow dash to move somewhat, now start disconnecting the million wires and reverse procedure to reinstall

Jun 10, 2010 | 1997 GMC Yukon

1 Answer

Remove battery from 2005 Yukon


Automotive batteries are required to be bolted down to help prevent tip over into engine belts and pulleys. There is usually a bolt going through a rubber block that is located in the front of the battery. this has to be removed in order to remove the battery. Good luck.

Jun 05, 2009 | 2008 GMC Yukon

2 Answers

Remove battery from 99 yukon


your gonna need either a 5/16 or 8mm wrench.  loosen the negative battery cable (black cable) off first and move it to the side where it wont touch the battery or anything metal.  then loosen and take off the positive (red) cable off and then just loosen the battery hold down bolt and the battery should left out. just like a top post battery make sure you dont touch anything metal with the wrench while loosing the bolts.

Feb 24, 2009 | 2008 GMC Yukon

3 Answers

Oil Pan Gasket Replacement - How to - GMC Yukon 2000


No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Jan 27, 2009 | 2000 GMC Yukon

2 Answers

Changing the starter on my 99 tahoe


Starter Escalade, Suburban, Tahoe, Yukon, Denali, Denali XL, Yukon XL, 1999 – 2005 REMOVAL&INSTALLATION
Removal & Installation
4.8L, 5.3L And 6.0L Engines
CAUTION Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Protective shields, as necessary
    • Starter solenoid shield
    • Starter-to-transmission close out cover bolt
    • Engine oil level sensor connection
    • On 4WD, front axle mounting bracket through bolt nut
  4. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Mounting bolts from the engine block. Slide the starter forward until the starter clears the transmission.
    • Starter transmission close out cover
    • Positive battery cable and wiring harness from the starter
    • Starter from the vehicle 0900c152800a6916.jpgStarter removal—4.8L, 5.3L and 6.0L engines
To install:
  1. Install or connect the following:
    • Starter
    • Positive battery cable to the starter. Tighten the nut to 12 ft. lbs. (16 Nm).
    • Starter transmission close out cover
    • Mounting bolts to the engine block and tighten to 37 ft. lbs. (50 Nm)
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Engine oil level sensor connection
    • Starter-to-transmission close out cover bolt
    • Starter solenoid shield
    • Protective shields as necessary
  3. Remove the safety stands.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
5.7L And 7.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Mounting bolts and shims
    • Wires
    • Heat shield
    • Starter
To install:
  1. Install or connect the following:
    • Starter
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Heat shield. Torque the bolts to 53 inch lbs. (6 Nm) and the nuts to 35 inch lbs. (3 Nm).
    • Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm).
    • Negative battery cable
6.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cables
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152800a6917.jpgExploded view of the starter motor—6.5L engine
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Starter
    • Mounting bolts/nuts and shim, if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inch lbs. (8.5 Nm).
    • Negative battery cables
8.1L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • On 4WD, front axle mounting bracket through bolt nut
  2. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Positive battery cable nut
    • Positive cable from the solenoid
    • Engine harness ground nut and ground from the solenoid
    • Mounting bolts and starter
    • Heat shield bolts, nut and shield, if necessary
To install:
  1. Install or connect the following:
    • Heat shield, bolts and nut if removed. Tighten the bolts to 35 inch lbs. (3 Nm) and the nut to 44 inch lbs. (5 Nm).
    • Starter and bolts. Tighten to 37 ft. lbs. (50 Nm).
    • Ground wire and nut. Tighten to 30 inch lbs. (3.4 Nm).
    • Positive cable and nut. Tighten to 80 inch lbs. (9 Nm).
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Negative battery cable

Sep 28, 2008 | 1999 Chevrolet Tahoe

Not finding what you are looking for?
2008 GMC Yukon Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...