Question about 1990 Oldsmobile Cutlass Ciera

1 Answer

Replace thermostat on 1990 cutlass ciera

I need to replace the thermostat on a 1990 cutless ciera. The engine is a 3300 side mounted. Would you be kind enough to give direction on how to do this?

Posted by on

  • Anonymous Mar 25, 2014

    need to know where tcc plugs into engine to disconnect

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 194 Answers

The easy way to find this is to fallow your bottom raditor hose to the engine where it attaches is called the thermostat housing remove the hose and remove the four bolts then take out the thermostat replace it and re install don't for get your antifreez you will need to replace it do to the loss when you remove the hose

Posted on Dec 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace thermostat


Follow the top radiator back to the engine at end of it will be the thermostat housing ther will be 2 bolts that mount it to the engine.Remove the 2 bolts and thermostat is underneath.

Jan 21, 2012 | 1994 Oldsmobile Cutlass Ciera

1 Answer

1990 ciera 3300 v 6 is stalling at idle and when backingup could that be a vacume problem


I would clean or replace the ISC (idle speed control) sensor, this sensor is what controls the idle speed of your engine.The sensor screw in to the side of the throttle body.will have a four wire harness connector going to it.

Aug 19, 2010 | 1990 Oldsmobile Cutlass Ciera

1 Answer

'88 cutless 3.8 6cyl. To replace starter remove exhaust manifold and other related items in way of starter. Question is how do you get exhaust manifold off without disconnecting front motor mount? {2}...


You don't have to remove anything but the starter assembly, starter will come out from under the car, flag labor time to do this job is .8 of an hrs.

Jul 12, 2010 | 1988 Oldsmobile Cutlass Ciera

1 Answer

HOW DO YOU GET TO THE PLUGS BETWEEN THE FIRE WALL AND ENGINE ON A CUTLASS CIERA 1990


Disconnect the engine torque mount on the top front , then you can pull the engine forward enough to reach the rear plugs

May 29, 2010 | 1990 Oldsmobile Cutlass Ciera

1 Answer

1990 cutlass ciera wont stay on..thermostat


The thermostat should be just off of the engine. Just follow the main rad hose from the radiator. Post if you need more.

Apr 21, 2010 | 1990 Oldsmobile Cutlass Ciera

1 Answer

How & where do I replace the signal flasher on 1990 olds ciera


hazard relay is located behind right side dash on convenience center box

Mar 04, 2010 | 1995 Oldsmobile Cutlass Ciera

1 Answer

In which area of the engine would I be able to find crank sensor


CRANKSHAFT POSITION SENSOR

Fig. 8 Ignition Coil Module Assy 2.5L/4-151 42188531 The Crankshaft Position Sensor is mounted remotely on the bottom side of the ignition module.

RH Side Of Engine. 42277335

Front RH Side Of Engine

Applicable to: Cutlass Ciera & Cutlass Cruiser w/V6-231/3.3L

Dec 11, 2009 | 1991 Oldsmobile Cutlass Ciera

1 Answer

How do I change the oil pan gasket on a 1990 olds. cutlass ciera(International Series).


you will have to un bolt the front engine mount raise the engine and then you may be able to get to the pan bolts but if you're not mecanically inclined you need to consult your nearest dealership

Oct 04, 2009 | 1990 Oldsmobile Cutlass Ciera

1 Answer

Hello i have an oldsmobile 1990 when its started work good but that go hot itsnot work corectly and go turn off


Have you tried replacing the Coolant Temperature Sensor? It's on the passenger side of the engine, under the engine part that says "3300" on the top. One is the sender for the temp. gauge, and the other is the one for the computer. The one on the right side is the CTS.

Sep 10, 2009 | 1990 Oldsmobile Cutlass Ciera

1 Answer

1990 Oldsmobile Cierra camshaft pully


do you mean crankshaft pulley? i dont know of a cam pulley on these.

if so replace the whole thing. the rubber on these go bad and rip away from the pulley. it happens. Just get a new one. should be a press fit one. may need a pulley puller. not the JAW type, but the 3 bolt type.
goold luck

Michael
ASE certified
plz rate

Feb 09, 2009 | 1990 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1990 Oldsmobile Cutlass Ciera Logo

Related Topics:

590 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...