Question about Dodge Intrepid

1 Answer

'95 Intrepid, intermitent problem, turn key on instrument cluster is dead, car will start but stuck in 2nd gear(creep home mode) vehicle will run 10sec-few min and then sometimes gaudges will come on line and vehicle will shift normally but sometimes shift rough. Sometimes when key is turned on gaudges are dead but will then come on line before starting the engine vehicle will operate normal. When vehicle works while running it never has the failure. Problem only occurs on start up. Vehicle has been looked at by Dodge dealership the computer was replaced and did not fix the problem.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Check for grounding problems for the computer area

Posted on Dec 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instrument Panel goes Dead for few minutes


I don't have a clue what the problem with your Instrument Panel is, but I can give you some advise. Email or Snail Mail your cars manufacturer and complain about your Dealer shotgunning the repair on your car and causing more damage.
It happened to a friend of mine and Corporate reimbursed him what he had paid the Dealer.
Good Luck.

Jan 11, 2014 | 2007 Ford Five Hundred

1 Answer

The gear gets stuck in 2nd gear


it is probably the pcm getting too hot and putting itself in limp home mode, faulty shift solenoids in the transmission will act the same way

Dec 11, 2013 | 2004 Dodge Intrepid

1 Answer

My security system will not disarm. my booklet said to press override/programing button. i cant find it in my truck.


normally, you just lock and unlock the door to disarm or rearm it.

SECTION 419-01: Anti-Theft - PATS 2002 F-150 Workshop Manual
DESCRIPTION AND OPERATION Anti-Theft -PATS The passive anti-theft system (PATS) contains the following components:
  • theft indicator
  • encoded ignition key
  • transceiver module
  • instrument cluster
  • powertrain control module (PCM)
  • standard corporate protocol (SCP) communication network
The PATS uses radio frequency identification technology to deter a driveaway theft. Passive means that it does not require any activity from the user. This system is known as SecuriLock® in North America, Safeguard® in the U.K. and PATS in continental Europe. This information can be found in owners literature.
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code, with over 72 million billion combinations.
Each encoded ignition key must be programmed into the vehicle's instrument cluster (the instrument cluster is also known as a hybrid electronic cluster [HEC]), before it can be used to start the engine. There are special diagnostic procedures outlined in the workshop manual that must be carried out if new encoded ignition keys are to be installed.
The encoded key is larger than a traditional ignition key. The key does not require batteries and should last the life of the vehicle.
The transceiver module communicates with the encoded ignition key. This module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends the data to the instrument cluster.
The control functions are contained in the instrument cluster. This module carries out all of the PATS functions such as receiving the identification code from the encoded ignition key and controlling engine enable. The instrument cluster initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
The PATS uses the PCM to enable or disable the engine. The instrument cluster communicates with the PCM over the SCP network in order to enable engine operation. The instrument cluster and the PCM use sophisticated messages in order to prevent a theft. The instrument cluster and the PCM share security data (when first installed together) that makes them a matched pair. After this security data sharing, these modules will not function in other vehicles. The shared PCM ID is remembered even if the battery is disconnected. The instrument cluster also stores the vehicle's key identification code even if the battery is disconnected. There are special diagnostic procedures outlined in this workshop manual that may be carried out if either a new instrument cluster or PCM needs to be installed.
All elements of PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator. This indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS problem, this indicator will either flash rapidly or glow steadily (for more than three seconds) when the ignition switch is turned to RUN or START. PATS also "blips" the theft indicator every two seconds at ignition OFF to act as a visual theft deterrent.
The PATS is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. Remote start systems must be removed before investigation of PATS-related no-start issues.

Apr 05, 2011 | 2004 Ford F150

1 Answer

Instrument cluster goes dead after starting vehicle feul tach and spedometer reads no bu5 fuse is good


Its a bad ignition. Wiggle the key while running and they should start working again. Good luck.

Oct 10, 2010 | 1999 Dodge Intrepid

1 Answer

I HAVE REPLACED THE PCM COMPUTER, ACTUALLY, I SENT MINE IN FOR REPAIR. THEY "FLASHED" IT, I PROVIDED VIN, AND ALL OTHER INFO REQUESTED. I REINSTALLED IT, CALLED LOCKSMITH TO "MATE" THE KEY AFTER IT...


SECTION 419-01: Anti-Theft — PATS 2000 F-150 Workshop Manual
DESCRIPTION AND OPERATION Anti-Theft —PATS The passive anti-theft system (PATS) contains the following components:
  • theft indicator
  • encoded ignition key
  • transceiver module
  • instrument cluster
  • powertrain control module (PCM)
  • standard corporate protocol (SCP) communication network
The PATS uses radio frequency identification technology to deter a driveaway theft. Passive means that it does not require any activity from the user. This system is known as SecuriLock® in North America, Safeguard® in the U.K. and PATS in continental Europe. This information can be found in owners literature.
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code, with over 72 million billion combinations.
Each encoded ignition key must be programmed into the vehicle's instrument cluster (the instrument cluster is also known as a hybrid electronic cluster [HEC]), before it can be used to start the engine. There are special diagnostic procedures outlined in the workshop manual that must be carried out if new encoded ignition keys are to be installed.
The encoded key is larger than a traditional ignition key. The key does not require batteries and should last the life of the vehicle.
The transceiver module communicates with the encoded ignition key. This module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends the data to the instrument cluster.
The control functions are contained in the instrument cluster. This module carries out all of the PATS functions such as receiving the identification code from the encoded ignition key and controlling engine enable. The instrument cluster initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
The PATS uses the PCM to enable or disable the engine. The instrument cluster communicates with the PCM over the SCP network in order to enable engine operation. The instrument cluster and the PCM use sophisticated messages in order to prevent a theft. The instrument cluster and the PCM share security data (when first installed together) that makes them a matched pair. After this security data sharing, these modules will not function in other vehicles. The shared PCM ID is remembered even if the battery is disconnected. The instrument cluster also stores the vehicle's key identification code even if the battery is disconnected. There are special diagnostic procedures outlined in this workshop manual that may be carried out if either a new instrument cluster or PCM needs to be installed.
All elements of PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator. This indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS problem, this indicator will either flash rapidly or glow steadily (for more than three seconds) when the ignition switch is turned to RUN or START. PATS also "blips" the theft indicator every two seconds at ignition OFF to act as a visual theft deterrent.
The PATS is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. Remote start systems must be removed before investigation of PATS-related no-start issues.


-------------------------------------------------------------------------------------------------------
Visual Inspection Chart Mechanical Electrical
  • Ignition lock cylinder
  • Encoded ignition key (PATS key)
  • Use of non-encoded ignition key (key without the molded plastic head, non-PAT key)
  • Use of a non-programmed encoded ignition key
  • Central junction box:
    • Fuse 2 (5A)
    • Fuse 6 (5A)
    • Fuse 30 (30A)
  • PATS transceiver
  • Connectors
  • Ignition switch

Mar 11, 2010 | Ford F-150 Cars & Trucks

1 Answer

My 2005 f150 wont star my anti theft system is


alarm rearms itself.

this is for 2001 and is similar.

Anti-Theft —PATS The passive anti-theft system (PATS) contains the following components:
  • theft indicator
  • encoded ignition key
  • transceiver module
  • instrument cluster
  • powertrain control module (PCM)
  • standard corporate protocol (SCP) communication network
The PATS uses radio frequency identification technology to deter a driveaway theft. Passive means that it does not require any activity from the user. This system is known as SecuriLock® in North America, Safeguard® in the U.K. and PATS in continental Europe. This information can be found in owners literature.
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code, with over 72 million billion combinations.
Each encoded ignition key must be programmed into the vehicle's instrument cluster (the instrument cluster is also known as a hybrid electronic cluster [HEC]), before it can be used to start the engine. There are special diagnostic procedures outlined in the workshop manual that must be carried out if new encoded ignition keys are to be installed.
The encoded key is larger than a traditional ignition key. The key does not require batteries and should last the life of the vehicle.
The transceiver module communicates with the encoded ignition key. This module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends the data to the instrument cluster.
The control functions are contained in the instrument cluster. This module carries out all of the PATS functions such as receiving the identification code from the encoded ignition key and controlling engine enable. The instrument cluster initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
The PATS uses the PCM to enable or disable the engine. The instrument cluster communicates with the PCM over the SCP network in order to enable engine operation. The instrument cluster and the PCM use sophisticated messages in order to prevent a theft. The instrument cluster and the PCM share security data (when first installed together) that makes them a matched pair. After this security data sharing, these modules will not function in other vehicles. The shared PCM ID is remembered even if the battery is disconnected. The instrument cluster also stores the vehicle's key identification code even if the battery is disconnected. There are special diagnostic procedures outlined in this workshop manual that may be carried out if either a new instrument cluster or PCM needs to be installed.
All elements of PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator. This indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS problem, this indicator will either flash rapidly or glow steadily (for more than three seconds) when the ignition switch is turned to RUN or START. PATS also "blips" the theft indicator every two seconds at ignition OFF to act as a visual theft deterrent.
The PATS is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. Remote start systems must be removed before investigation of PATS-related no-start issues.

------------------------------------
Visual Inspection Chart Mechanical Electrical
  • Ignition lock cylinder
  • Encoded ignition key (PATS key)
  • Use of non-encoded ignition key (key without the molded plastic head, non-PAT key)
  • Use of a non-programmed encoded ignition key
  • Central junction box:
    • Fuse 2 (5A)
    • Fuse 6 (5A)
    • Fuse 30 (30A)
  • PATS transceiver
  • Connectors
  • Ignition switch

May 11, 2009 | 2005 Ford F-150

1 Answer

How to replace the antenna ring that is wrapped around the ignition?


what year?

here's 1990. It may be the instrument cluster that's the issue.
You never said what the prnlem is.
Did you reporgram the keys to the new module?

Please rate as fixe
Anti-Theft —PATS The passive anti-theft system (PATS) contains the following components:
  • theft indicator
  • encoded ignition key
  • transceiver module
  • instrument cluster
  • powertrain control module (PCM)
  • standard corporate protocol (SCP) communication network
The PATS uses radio frequency identification technology to deter a driveaway theft. Passive means that it does not require any activity from the user. This system is known as SecuriLock® in North America, Safeguard® in the U.K. and PATS in continental Europe. This information can be found in owners literature.
The PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code, with over 72 million billion combinations.
Each encoded ignition key must be programmed into the vehicle's instrument cluster (the instrument cluster is also known as a hybrid electronic cluster [HEC]), before it can be used to start the engine. There are special diagnostic procedures outlined in the workshop manual that must be carried out if new encoded ignition keys are to be installed.
The encoded key is larger than a traditional ignition key. The key does not require batteries and should last the life of the vehicle.
The transceiver module communicates with the encoded ignition key. This module is located behind the steering column shroud and contains an antenna connected to a small electronics module. During each vehicle start sequence, the transceiver module reads the encoded ignition key identification code and sends the data to the instrument cluster.
The control functions are contained in the instrument cluster. This module carries out all of the PATS functions such as receiving the identification code from the encoded ignition key and controlling engine enable. The instrument cluster initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
The PATS uses the PCM to enable or disable the engine. The instrument cluster communicates with the PCM over the SCP network in order to enable engine operation. The instrument cluster and the PCM use sophisticated messages in order to prevent a theft. The instrument cluster and the PCM share security data (when first installed together) that makes them a matched pair. After this security data sharing, these modules will not function in other vehicles. The shared PCM ID is remembered even if the battery is disconnected. The instrument cluster also stores the vehicle's key identification code even if the battery is disconnected. There are special diagnostic procedures outlined in this workshop manual that may be carried out if either a new instrument cluster or PCM needs to be installed.
All elements of PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator. This indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS problem, this indicator will either flash rapidly or glow steadily (for more than three seconds) when the ignition switch is turned to RUN or START. PATS also "blips" the theft indicator every two seconds at ignition OFF to act as a visual theft deterrent.
The PATS is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. Remote start systems must be removed before investigation of PATS-related no-start issues.
---------------------------------------------------------------------------
Symptom Chart Condition Possible Sources Action
  • No communication with the module — instrument cluster
  • Central junction box:
    • Fuse 2 (5A).
    • Fuse 6 (5A).
    • Fuse 30 (30A).
  • Circuitry.
  • GO to Pinpoint Test A .
  • The anti-theft indicator is always/never on — no three-second theft indicator prove-out
  • Instrument cluster.
  • Theft indicator.
  • GO to Pinpoint Test B .
  • The vehicle does not start — theft indicator proves out for three seconds as normal
  • Less than two keys programmed to the system.
  • Transceiver not connected/defective.
  • Circuitry.
  • Transceiver internal antenna damaged.
  • NON-PATS key, damaged key or no code received.
  • Partial key read of PATS key.
  • Unprogrammed PATS key.
  • PERFORM instrument cluster on-demand self-test. RETRIEVE DTCs. If DTCs are present, GO to Instrument Cluster Diagnostics Trouble Code (DTC) Index. If no DTCs are retrieved, CHECK for other possible no-start causes.
  • No PCM ID stored in PATS.
  • PATS/PCM ID do not match.
  • Problem with SCP link.
  • CLEAR the stored DTCs. CYCLE the ignition key from off to run. RETRIEVE continuous DTCs. If DTCs are present, GO to Instrument Cluster Diagnostics Trouble Code (DTC) Index. If no DTCs are retrieved, CHECK for other possible causes.
  • The alarm system does not operate properly — the vehicle starts but flashes a fault code on theft indicator at key on
  • Incorrect PCM calibration.
  • GO to Pinpoint Test C .

--- Key Programming —Program a Key Using Two Programmed Keys NOTE: This procedure only works if two or more programmed ignition keys are available and it is desired to program additional key(s). If two keys are not available, follow the procedure in Key Programming—Erase All Key Codes and Program Two Keys .
NOTE: PID SPARE_KY must be enabled for this procedure to operate. If this Parameter Identification (PID) Index is not enabled, follow the security access procedure and select Spare Key Programming Switch: Enabled.
NOTE: If the programming procedure is successful, the new key(s) will start the vehicle and the THEFT INDICATOR will illuminate for approximately three seconds.
NOTE: If the programming procedure is not successful, the new key(s) will not start the vehicle and the THEFT INDICATOR will flash. If the programming procedure was not successful, repeat the key programming procedure from Step 1. If the failure repeats, check Circuit 729 (RD/WH) (hot at all times) in instrument cluster for proper battery voltage. Repair the circuit if voltage is not present. For additional information, refer to Diagnosis and Testing to review diagnostic trouble codes (DTCs) and perform pinpoint tests as required.
NOTE: A maximum of eight ignition keys can be programmed to a passive anti-theft system (PATS) equipped vehicle. Use PID NUMKEYS to determine how many keys are programmed to the vehicle.
NOTE: If the steps are not performed as outlined, the programming procedure will end.
NOTE: Ignition keys must have correct mechanical key cut for the vehicle and must be a PATS encoded key.
  1. Insert the first programmed ignition key into the ignition lock cylinder and turn the ignition switch from OFF to RUN (maintain the ignition switch in RUN for one second).
  1. Turn the ignition switch to OFF and remove the first key from the ignition lock cylinder.
  1. Within five seconds of turning the ignition switch to OFF, insert the second programmed ignition key into the ignition lock cylinder and turn the ignition switch from OFF to RUN (maintain the ignition switch in RUN for one second).
  1. Turn the ignition switch to OFF and remove the second key from the ignition lock cylinder.
  1. Within 10 seconds of turning the ignition lock cylinder to OFF, insert the unprogrammed ignition key (new key) into the ignition lock cylinder and turn the ignition switch from OFF to RUN (maintain the ignition switch in RUN for 1 seconds

Apr 24, 2009 | Ford F-150 Cars & Trucks

2 Answers

1995 Cougar Odometer/trip-meter inop


Section 13-01: Instrument Cluster—Conventional 1995 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION Instrument Cluster Removal and Installation
  1. Disconnect battery ground cable (14301) .
  1. Remove screws holding instrument panel reinforcement (017A28) .
  1. Remove screws holding instrument panel lower shield (045G02) .
  1. Remove fasteners holding steering wheel column as outlined in Section 11-04 . Gently lower steering column.
  1. Remove fasteners holding the instrument panel finish panel (044D70) and gently pry off.



  1. Remove four instrument cluster retaining screws. (Do not remove screws from the instrument cluster main lens (10887) and instrument cluster mask (10890) ).
  1. Slide the instrument cluster (10849) to the right of the instrument panel opening and unhook the instrument panel harness from the back of the instrument cluster .
  1. Remove the instrument cluster from the instrument panel (04320) .
-----------------------
Speedometer/Odometer Federal law requires that the odometer in any replacement speedometer (17255) must register the same mileage as that registered in the removed speedometer . Since the speedometer mileage cannot be reset on this unit, affix odometer sticker to driver's door pillar and record original vehicle mileage. Removal
  1. Disconnect battery ground cable (14301) .
  1. Remove the instrument cluster (10849) as outlined.
  1. Remove seven screws retaining the instrument cluster mask (10890) and instrument cluster main lens (10887) .
  1. Remove speedometer assembly.
Installation
  1. Position the speedometer assembly to the instrument cluster back plate (10848) and install.
  1. Position the instrument cluster mask and instrument cluster main lens to the instrument cluster back plate and install the seven retaining screws.
  1. Install the instrument cluster as outlined.
  1. Connect battery ground cable and check the operation of the speedometer .
please rate if this helps

Mar 24, 2009 | 1994 Mercury Cougar

1 Answer

94 dodge intrepid won't start.


Sounds like trans range switch. It is stuck in 2nd because it has a trans code in the tcm. Chrysler calls this (limp-in mode). You need to scan the tcm for codes, It likely has a code for the range switch. Hope this helps. By the way the range switch is also the neutral safety switch for the starter.

Mar 02, 2009 | 1994 Dodge Intrepid

1 Answer

Automatic transmission is stuck in 2nd gear (limp mode)


most newer vehicles  have transmission control modules,that go to a default of 2nd or 3rd gear when they go bad!  I had a 91 plymouth stuck in 3rd gear because of this module! could be your problem!    when mine went out, it smelled like something electrical burned inside the the passenger cabin! I would check all the electrical connections on the transmission first    good luck   

Jan 02, 2009 | 1998 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

71338 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7018 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...