How to remove the tail light assembly of Mazda mpv 2002
I remvoved the two screws, Even after that, the assembly is still not removeable. In one of the WIKIs it is suggested to push forwar.
Can some provide more details on how to remove the assembly
I appreciate your help,
An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert that has over 500 points.
An expert who has answered 200 questions.
Re: How to remove the tail light assembly of Mazda mpv...
It is not just held with those two screws only, after removing the screws push it forward which means if you are removing the right side assembly, push the whole assembly futther to the right likewise if you are doing the left push it out to the left.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Open the tailgate(s) completely and you'll find two phillips-head screws on the inside edge of the tail light assembly. Take out those two screws (keep one hand on the assembly when you remove the last screw) and the whole tail light assembly will come off of the vehicle. On the back side of the tail light assembly, twist and remove the light bulb housing for the blown bulb. The bulbs themselves on some models vary in the manner in which they are removed: (1) If the base on the bottom of the bulb itself is a *round* brass base, press down on the bulb then twist it to remove it, or (2) If the base on the bottom of the bulb itself is *flat* plastic, pull the bulb straight out of the assembly. To replace the bulb, simply reverse the order. Best wishes!
It will be either on the outside with 2 small screws or more likely you need to remove a trim/cover of the top headliner area... If still in doubt goto or phone the dealer and just ask the parts dept person to show it to you...
If similar to 2002 MPV, you detach the whole side light module, then pop out the bulb-socket, then you can replace the bulb. You need a philips screwdriver, medium size.
Open the back hatch.
Remove the two screws on the inside edge of the light-assembly.
Now pull the whole assembly *sideways* not back - it is held by two detent-pins that face out. You can swing it out a bit and then carefully lever it at top or bottom edge.
Lower the assembly face-down, you can see three bulb-sockets. They can be turned a part-turn, I think counter-clockwise, then they pop out. Replace bulb(s), re-insert socket, push assembly back onto pins, replace screws. Just did this for brake/tail light 10 minutes ago.
open the rear tail gate there should be a couple of screws on the inside near the rubber seal just remove them and the assbilme should pull ot and the bulb may be a twist lock and pull ot and remove the bulb
Removal of the rear bumper on an Mazda 2004 to 2006 MPV.
It's afairly simple task: 1) Open the rear hatch or (door) remove the torx screws at the bottom of the weather strip. 2) Remove both tail lights by unscrewing the two phillip screws on each light, once removed the lights pulling toward the side of the van. Let them hang from the wires. You will see a clip (white in color),pry it out from behind the bumper material and go to the next step. 3) Remove three 8mm head screws in each fender well and three plastic clips. Then remove an 8mm screw at the top corner of the bumper against the rear fender. If your car has splash guards remove them as well. 4) Remove the two clips at the bottom of the bumper attached to the under carriage. 5) Pull the bumper toward the back of the vehicle be careful with the tail lights. Remember, they are hanging loose.
And that's it, you have done it.