Question about 1989 Jeep Comanche

2 Answers

I cant fugure out what kind of rear end i have in my comanche

The bearings got eaten up in the back passenger side and i need to know what rear end i have because the tag is gone

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 23 Answers

Most bearings have number by the one side u can use the empressed number on the bearing to get the size, and or go for the whole rear end of that model

Posted on Dec 04, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 261 Answers

The easiest way to solve it is to remove the axel which is damaged and take the number off of the damaged bearing and replace it with the matching number of the bearing

Posted on Dec 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 mazda mpv passenger side ball bearing location


The following items on your Mazda have ball bearings, and are on the passenger side.
1) Wheel bearings, front and rear.
2) CV joints, inner and outer.
3) Alternator, front and rear.
4) Power steering pump.
5) Water pump.
6) Idler pulley and/or tensioner pulley.
7) A.C. Compressor.
8) a few I may have missed.

Oct 29, 2015 | 2000 Mazda MPV

1 Answer

Tire sets very close on rear fender wall on front passenger side of car


Take it to an accredited front end specialist as from your description you have a serious problem

Mar 18, 2014 | 1994 Mercury Grand Marquis

1 Answer

I am trying to replace the passenger side hub and bearing,before i tear it down i need to know if the bearing is just pressed onto the new hub and then the whole assembly slides onto the splined end of the...


Hello texasjagfan: My name is Roger and I will help you. The front hub bearings are press out bearings and you will need a press in order to change them. You will need to remove the front spindle to gain access to the bearings.You also will need an alignment when finished replacing the front bearings. The rear bearings are a hub and bearing unit.
Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Aug 18, 2011 | 2003 Chrysler PT Cruiser

1 Answer

I own a Mazda MX5 2002 model. It has developed a groaning sound from the back end passenger side. It stsrts when the car is in motion and then as it speeds up it disappears. It is getting louder recently...


I would strongly suspect that you have a rear wheel bearing breaking down. Nasty nasty sound, potential for nasty results if you don't get it rectified (Like the bearing breaking down completely and the wheel coming off in extreme circumstances, but this is very unlikely). The good news is, it's very easily fixed and shouldn't be that expensive. Just bear in mind that these sounds are notorious for transmitting around the vehicle, so even if you think you can hear the noise from the passenger side, check out the drivers side too.

Jul 29, 2011 | Mazda MX-5 Miata Cars & Trucks

1 Answer

Severe whining in the rear end. I have had all bearings replaced. some wear was noted on the rear passenger side axle. extended bearing was used as a replacement so it would not be in contact with scored...


The bearings usually make a kind of rumbling sound, whining usually is gears that are not set up right. They would have to have your differential out in order to replace all of the bearings, if that is the case you need to get it back to whoever did the work and have them make it right. You should get it back to them before any major damage occurs.

Jan 25, 2011 | 2000 Chevrolet Blazer

2 Answers

Roaring noise from Rear Wheel when braking and turning


This is just because of the warned out wheel bearings just replace the bearings of the rear wheels to sort out this issue.

Jul 22, 2009 | 2001 Nissan Sentra

1 Answer

89 Jeep Comanche needs front wheel bearings. Removed wheel, caliper, but cant remove rotor. Am I missing something or is the rust still holding on? It looks like it has teeth around spindle. Do I need to...


4x4, correct? Put the nut back on the axle and run it flush with the end, then give it a smack with a hammer to get the axle splines free.
The rotor itself is separate from the hub ...spray with wd40 or other solvent and squirt some where the lugs come through . Put a 2x4 on it and give it a smack with the same hammer. If necessary, alternate at opposite sides. it should break free.

Apr 26, 2009 | 1989 Jeep Comanche

1 Answer

Rear passenger side axle keeps blowing out the seal


probably bearing now!! I would call dealer on this one that is unusual you might be surprised have vin# ready ask if there was a call back on this! good luck

Dec 31, 2008 | 2004 Ford F150

1 Answer

I cant figure out what kind of rear end i have in mu comanche


ONE OF TWO, OVAL HOUSING COVER,DANA 35 ,STOP SIGN SHAPE DANA 44 .

Dec 04, 2008 | 1989 Jeep Comanche

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...