Question about 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

How to reset brake pads message on dash of mbz E320 2005?

Posted by on

  • Tom Hennessy
    Tom Hennessy Mar 27, 2013

    I refuse to take it to the dealer because the is on, I put electrical tape over it

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 251 Answers

The only way is to take it to a dealer

Posted on Dec 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change brake pads warning message on a 98 cadillac seville


Anthony, that's something that you'll probably have to go to a dealer to get reset.

Mar 13, 2014 | Cars & Trucks

1 Answer

Brake light on and beeping message center telling hand brake is on but it is not


some models have a pad wear sensor when the pad wears down it triggers a orange light but some are red

Jul 12, 2012 | 2004 Volkswagen Jetta

1 Answer

How do i turn off the brake warning light on range rover 2004


You can reset this fault code using the buttons on your dash - you don't need a dealer to do this. As you already know, you need to replace your pads and the brake wear sensor - this is a sacrifical item. Once this is done, do the following:-
Using the buttons on your dash - there are 2 - one on the LHS (Trip reset) and one on the RHS (In between Tacho and temp gauge)

*Press and hold Right button and turn ignition to first position (I or Accessory)Display should show "Check Control OK" then a short time later "Test Nr.01"*Press the Left button and you should see the car info in the display. Add the last FIVE digits of the car identity number together (NOT all 6!) to get a unique ID for your car.*Press the Right button repeatedly until you see "Test Nr.19"*Press and hold the Left button until you see the number matching the unique ID you calculated, then release.*Press the Right button to select this.*Press the Left button repeatedly until you see "Test Nr.21" - Reset All Defect Codes*Press Right button to reset the codes.Done!

Mar 26, 2012 | 2004 Land Rover Range Rover

2 Answers

I bought a 98 z3 and i need to find a diagram of the dash lights, i have a red circle light with dashes around it and i don't know what it means


it's a break pad sensor, your pads are worn out,if you wait to long, you"ll ware thru the sensor and have to replace it. it's not a hard fix, you"ll have to clear the code to remove the dash diagram, after u fix the brakes, and maybe the sensor, good luck

Mar 10, 2011 | 1998 BMW Z3 Roadster

1 Answer

I have a VW touran diesel 1.9. Recently there was a brake pad warning light indicated on my dash board, so I took it to my closest gargae to check. They replaced two new brake discs and the brake pads....


nope,it has to go back to a dealer(the computer is too expensive for a diy mech)they will reset it IF GENUINE parts have been used, as sensors are inbuilt into the pads.

Jan 24, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

Brake fault light went off on the dash? Car operates unaffected and brakes are working fine. Do I need to reset the onboard computer?


NO. YOUR BRAKE PADS HAVE SENORS IN THEM.ONE IN THE FRONT AND REAR. YOUR GETTING CLOSE TO NEEDING NEW PADS.

Mar 13, 2010 | 2004 Volkswagen Passat

1 Answer

Resetting brake warning light


Hi , if you turn the ignition on so that all the dash lights are on , do not start the engine and leave on for aprox 45 seconds the brake pad warning lights should go out, regards mark

Jul 29, 2009 | 1999 BMW 328 Series

4 Answers

Brake pad llight on audi 2001 a6


In the past I had the same problem with new pads!
You must check up if new brake pads electrical wires are OK. Try as follows:
1. Disconnect only new brake pads wires from the vehicle electrical circuit.
2. Extract old brake pads wires from old brake pads.
3. Insulation wear cap from old brake pads wires.
4. Connect old brake pads wires on the vehicle electrical circuit.
5. Switch ignition ON and start engine.
Now the wear light must go off !
Please Rate my Response! Thanks!

Jul 23, 2009 | 2001 Audi A6

2 Answers

I replaced the front pads on a VW JETTA 2.5 and the check pads light is on. How can I reset the check pads light?


As the brake pads wear, the brake pad wear sensor contained in the brake pad contacts the brake rotor. This causes the sensor to fail. When a pad wear sensor fails it opens the ground circuit of the pad wear warning light system causing the pad wear warning light to illuminate. Perform normal brake service to correct this condition and be sure to replace the brake pads with pads containing wear sensors. Once the brake pads and wear sensors are replaced, reset the brake pad warning system by turning the ignition switch to the "on" position. As long as continuity to ground exists through all the brake pad wear sensors the system should reset and the pad warning light in the dash will go out. If the pad warning light does not go out, a check of the pad warning circuit for an open circuit condition or poor ground must be performed.

Mar 03, 2009 | 2005 Volkswagen Jetta

4 Answers

Brake Pad Sensor


On my bmw 325i front pads changed,indicator on dash still on,help!!

Jun 11, 2008 | 2003 BMW 325

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

673 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

164 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...