Question about 1995 Pontiac Bonneville

1 Answer

Where is pcv valve location

95 pontiac bonn.,3.8 supercharged,vin#1,was going to replace pcv valve but can not seem to find the location to do so.can you point me in the right direction? it used to be so simple on the old v-eights,sixes,ect.,pop the old one out the valve cover and in with the new.im sure ive over looked it ten times by now,part store gave me an old school pcv valve im wondering if it is the right one? on top the intake manifold under the super charger cover there is a place that says pcv valve withe two bolts,took bolts out but the plate dont budge.thought id ask first as i have a knack of breaking everything i touch.thanks for your effort and time,good looking out guy's & gal's if any.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Its in the valve cover

Posted on Dec 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 pontiac grand prix gtp 3.8 supercharged and i want to know if it has a pcv valve and if it does where?


the last one I did was on the passenger side on top of the intake. it was covered with a flat plate that was held in place with 2 bolts I think. remove the plate and the PCV is under the cover. pull out valve there is a spring between the cover and the valve, make sure it is put back in place when re-assembling. it does not use a hose to control crankcase pressures.

Aug 27, 2015 | 2000 Pontiac Grand Prix GTP

1 Answer

PCV valve on 2006 Suzuki Aerio sx


locating on car, or in a store?
the service manual covers this, (alldata dot com)
some cars dont have one. Like my jeep.
but they all can and will clog, that is for sure.

but on all cars. (teaching how to fish).
the PCV has 2 ends.
1 end goes to the intake plenum (vacuum source)
the 2nd end goes to the top of the valve cover (engine top cover)
it does that, to **** fumes from there, so must go there.
directly or via a hose. just look there, and see it.
some times it fits in a VC(valve cover) boot that hides it.

but is here. all the time, every day.

some of these cars have many engine choices
so not stating VIN or engine type. its all guessing.
get and FSM
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

the factory FSM is expensive to the extreme.
so I post the bet source and price.

Jan 29, 2013 | 2006 Suzuki Aerio SX

1 Answer

2006 dodge charger pcv valve location


5.7L


9491.jpg The PCV valve (3) is mounted into the top/right side of the intake manifold (2).

9493.jpg
1.The PCV valve (1) is sealed to the intake manifold with two O-rings (2).
2.Remove PCV valve by rotating counter-clockwise 90 degrees until locating tabs (3) have been freed. After tabs have cleared, pull valve straight up from intake manifold.3.After valve is removed, check condition of two valve O-rings (2). __________________

Oct 07, 2010 | 2006 Dodge Charger

2 Answers

Replacing the MAP sensor??


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Locate the MAP sensor and remove the retaining screws
  3. Detach the electrical connector.
99e56ea.jpg

Fig. On the 3.1L engine, the MAP sensor is located alongside the intake manifold

06cd371.jpg

Fig. MAP sensor and its bracket arrangement-3.4L (VIN E) engine

c92a20a.jpg

Fig. Location of the MAP sensor on the throttle body adapter-3.4L (VIN X) Engine

ef21261.jpg

Fig. The MAP sensor is located just behind the throttle body mounting base-3.5L (VIN H) engine

c7cd8f9.jpg

Fig. MAP sensor and its location alongside the supercharger-3.8L (VIN 1) Engine

98ee1cd.jpg

Fig. On the 3.8L (VIN K) engine, the MAP sensor is located on top of the PCV valve cover
  1. Remove the vacuum hose and lift the MAP sensor from the engine.
  2. Installation is reverse of the removal procedure.

Hope helps (remember rated and comment this).

Aug 06, 2010 | 2000 Oldsmobile Intrigue

3 Answers

Have not had the pcv changed in a while and cannot locate it. 2000 Pontiac Grand Prix 3800 series 3, with super charger.


If I remember correctly this vehicle has a plastic plenum and the pcv valve is inside the plenum. Only time it is usually replaced is when the intake gasket needs replaced (and it will).

Nov 22, 2009 | 2000 Pontiac Grand Prix

2 Answers

Location of pcv valve on 03 ford focus


http://www.focushacks.com/images/pcv.jpg
Here's a picture to locate it..
So, when looking at the engine from above, on the right of the exhaust.

Procedure to replace it
1) Lift and support the front end of your car, or drive up on ramps
2) Get under the front of your car. The PCV Valve is located behind the exhaust manifold, a few inches below the valve cover.
3) Push up on the PCV valve to pop it out of the tube, or pull. You can get it out of the rubber tube with some effort.
4) Remove the rubber elbow from the top of the PCV valve. This can be re-used if it's not squishy. It can also be replaced cheaply.
5) Put the elbow on the new PCV Valve
6) Re-attach the elbow to the PCV tube
7) Push the new PCV valve back down into the large rubber tube

Sep 25, 2009 | 2003 Ford Focus

1 Answer

Want to locate pvc valve on 2000 pontiac grand am 6 cyl


You'll find the PCV valve on the right side of the front valve cover. You'll need to remove the valve in order to troubleshoot it to determine if you need a replacement. To remove, pull the PCV valve out of the cover and detach the hose

Test the old PCV valve to determine if it needs replacing. Blow air through it in order to see if it is clogged. If it does not seem to ventilate, then you'll need to install a new valve.

Pop the new PCV valve into the spot of the old valve. With the correct part, it should snap right in. Take the hose and reattach it in order to complete the installation.

Aug 21, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Can't seem to locate the pcv on friends 99 gtp supercharged anybody know where it is located?


It is located behind the supercharger rotor housing on the drivers' side, almost straight across from the intake plenum. It is mounted beneath a rhombus shaped plate with 2 1/4" bolts. The valve is mounted on top of a spring and there is a gasket on the bottom of the plate so be careful not to break it...it's not rubber. The plate holding it down also bolts into aluminum so don't over tighten.

Jun 12, 2009 | 1999 Pontiac Grand Prix

2 Answers

Excessive Oil consumption, 1995 Bonneville Vin K 3.8


U need o repair the pcv vacuum source it is the cause of the oil consumption, which is excessive crankcase pressure.

Mar 12, 2009 | 1995 Pontiac Bonneville

1 Answer

Bonn. super charge intake manifold gasket help please


head or block maybe cracked,headgasket bad,,get a dif. mechanic for a second opinion.

Feb 22, 2009 | 1995 Pontiac Bonneville

Not finding what you are looking for?
1995 Pontiac Bonneville Logo

Related Topics:

384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...