Question about 2003 Ford Focus

1 Answer

Tie rod hello all i slide into a pole and the tie rod snapped... how do i install a new one

Posted by on

  • tiggadog13 Dec 03, 2008

    thanks how much do you think one will cost and what does it look like

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 60,769 Answers

You will need a cheap tie rod joint separator, once you pop the ball joint loosen the inner lock nut and it just screws off, you will need an alignment.

Posted on Dec 03, 2008

  • yadayada
    yadayada Dec 03, 2008

    Check with a Ford dealer on the price.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace cv joints


Hi Douglas, I'm glad to help. My first suggestion is to get to complete shaft. This way you want have any problems later on. It's not that much more expensive and you'll be glad you did. Below is the procedure for replacing them.



FRONT DRIVESHAFTS

REMOVAL
  1. Raise vehicle on jack stands or centered on a frame contact type hoist. Refer to Hoisting in the Lubrication And Maintenance section of this manual for the required lifting procedure to be used for this vehicle.
  2. Remove the cotter pin and nut lock Hub And Bearing To Stub Axle Retaining Nut from the end of the stub axle.
  3. Remove the wheel and tire assembly from the vehicle.
  4. Remove the wave washer Wave Washer from the end of the stub axle CAUTION: Wheel bearing damage will result if after loosening hub nut, vehicle is rolled on the ground or the weight of the vehicle is allowed to be supported by the tires.
  5. With the vehicle's brakes applied to keep hub from turning, loosen and remove the stub axle to hub nut.
  6. Remove the two front disc brake caliper to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts
  7. Remove the disc brake caliper from the steering knuckle. Caliper is removed by first rotating top of caliper away from steering knuckle and then removing bottom of caliper out from under machined abutment on steering knuckle Brake Caliper Mounting To Steering Knuckle
  8. Support disc brake caliper assembly by using a wire hook and suspending it from the strut assembly Correctly Supported Disc Brake Caliper Do not allow the brake caliper assembly to hang by the brake flex hose.
  9. Remove the brake rotor from the hub and bearing assembly Remove/Install Brake Rotor
  10. Remove nut attaching outer tie rod end to steering knuckle Removing Tie Rod End Attaching Nut Nut is to be removed from tie rod end using the following procedure, hold tie rod end stud with a 11/32 socket while loosening and removing nut with a wrench.
  11. Remove tie rod end from steering knuckle using Remover, Special Tool MB-991113 Tie Rod End Removal From Steering Knuckle Arm
  12. Remove the steering knuckle to ball joint stud, clamping nut and bolt Control Arm To Steering Knuckle Attachment from the steering knuckle.
  13. Using a pry bar, separate steering knuckle from ball joint stud Separating Ball Joint Stud From Steering Knuckle Note: Use caution when separating ball joint stud from steering knuckle, so ball joint seal does not get cut. NOTE: Care must be taken not to separate the inner C/V joint during this operation. Do not allow driveshaft to hang by inner C/V joint after removing outer C/V Joint from the hub/bearing assembly in steering knuckle, end of driveshaft must be supported.
  14. Pull steering knuckle assembly out and away from the outer C/V joint of the driveshaft assembly Steering Knuckle Separation From Driveshaft
  15. Support the outer end of the driveshaft assembly. Insert a pry bar between inner tripod joint and transaxle case Disengaging Inner Tripod Joint From Transaxle Pry against inner tripod joint, until tripod joint retaining snap ring is disengaged from transaxle side gear.
  16. Hold inner tripod joint and interconnecting shaft of driveshaft assembly. Remove inner tripod joint from transaxle, by pulling it straight out of transaxle side gear and transaxle oil seal Tripod Joint Removal from Transaxle When removing tripod joint, do not let spline or snap ring drag across sealing lip of the transaxle to tripod joint oil seal.
INSTALLATION
  1. Thoroughly clean spline and oil seal sealing surface, on tripod joint. Lightly lubricate oil seal sealing surface on tripod joint with fresh clean transmission lubricant.
  2. Holding driveshaft assembly by tripod joint and interconnecting shaft, install tripod joint into transaxle side gear as far as possible by hand Tripod Joint Removal from Transaxle
  3. Grasp inner tripod joint an interconnecting shaft. Forcefully push the tripod joint into side gear of transaxle, until snap ring is engaged with transaxle side gear. Test that snap ring is fully engaged with side gear by attempting to remove tripod joint from transaxle by hand. If snap ring is fully engaged with side gear, tripod joint will not be removable by hand.
  4. Clean all debris and moisture out of steering knuckle, in the area were outer C/V joint will be installed into steering knuckle.
  5. Ensure that front of outer C/V joint which fits against the face of the hub and bearing is free of debris and moisture before installing outer C/V joint into hub and bearing assembly Outer C/V Joint Inspection
  6. Slide drive shaft back into front hub and bearing assembly. Then install steering knuckle onto the stud of the ball joint assembly Steering Knuckle Separation From Driveshaft
  7. Install a new steering knuckle to ball joint clamping bolt and nut Control Arm To Steering Knuckle Attachment Tighten the clamping bolt and nut to a torque of 135 N·m (100 ft. lbs.)
  8. Install tie rod end into steering knuckle. Start attaching nut onto stud of tie rod end. While holding stud of tie rod end stationary using a 11/32 socket, Removing Tie Rod End Attaching Nut tighten tie rod end to steering knuckle attaching nut. Then using a crowfoot and 11/32 socket Torquing Tie Rod End Attaching Nut , tighten the tie rod end attaching nut to a torque of 54 N·m (40 ft. lbs.)
  9. Install braking disc on hub and bearing assembly Remove/Install Brake Rotor
  10. Install disc brake caliper assembly on steering knuckle. Caliper is installed by first sliding bottom of caliper under abutment on steering knuckle, and then rotating top of caliper against top abutment Brake Caliper Mounting To Steering Knuckle
  11. Install disc brake caliper assembly to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts Tighten the disc brake caliper assembly attaching bolts to a torque of 22 N·m (195 in. lbs.)
  12. Clean all foreign matter from the threads of the outer C/V joint stub axle. Install the washer and stub axle to hub/bearing assembly nut on stub axle and securely tighten nut.
  13. Install front wheel and tire assembly. Install and tighten the wheel mounting stud nuts in proper sequence until all nuts are torqued to half the required specification. Then repeat the tightening sequence to the full specified torque of 135 N·m (100 ft. lbs.)
  14. Lower vehicle.
  15. With the vehicle's brakes applied to keep hub from turning, tighten the hub nut to a torque of 244 N·m (180 ft. lbs.) Torquing Front Stub Axle To Hub Nut
  16. Install the spring wave washer on the end of the stub axle.
  17. Install the hub nut lock, and a new cotter pin Hub And Bearing To Stub Axle Retaining Nut Wrap cotter pin prongs tightly around the hub nut lock as shown in Hub And Bearing To Stub Axle Retaining Nut
  18. Check for correct fluid level in transaxle assembly. Refer to Group 21, Transaxle for the correct fluid level checking procedure for the type of transaxle being checked.
  19. Set front toe on vehicle to required specification.

May 07, 2014 | 2000 Dodge Caravan

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

1 Answer

My Pontiac Bonneville has a popping noise when i hit a bump i think its the tie rod ends i don't know if its inner or outer. How can i tell what the problem is and how hard it is to fix.


does it kinda sound like two peices of metal striking each other? most likely the outer tie rod end. the inner tie rod end wouldnt make a sound anything like that, it would snap and you wouldnt be able to steer the car very well.....regardless, this is easy to check. remove the wheel. the object directly behind your brakes is the wheel hub, directly behind the wheel hub is the steering knuckle. connected to the steering knuckle you should find the strut up top, a control arm on the bottom, the sway bar attaches towards the front of the car, the outer tie rod end connects to the hub on the side closest to the rear of the car. connected to the outer tie rod end is the tie rod, which is then connected to your power steering rack and pinion via the inner tie rod ends. you want to locate the outer tie rod end and examine it visually. is the rubber cracked, torn, or missing? if so, replace the outer tie rod end. you will need a 2 jaw puller to remove the old tie rod end, but removal and installation is EASY (i taught my wife how to do it in 5 minutes and she did it successfully in less than 10). depending on how far the jam nut is moved when replacing the tie rod, you may need an alignment after replacing it. if the rubber on the tie rod end looks fine, the noise is probably coming from the strut. when the struts are worn out, the strain of the vehicle bouncing is put on the coil over springs. after a while, the spring can become worn out as well.....this would create a "clunking" sound when going over bumps.....and, if the spring wears out too much, you MIGHT be able to hear a metalic popping sound when the struts reach the damper if the spring hasnt expanded that far yet (this is extremely unlikely tho, more likely than not, the spring would crack/break LONG before you hear this noise and the car would be close to undriveable......). regardless, out tie rod ends are roughly 12-15 bucks each and extremely easy to install. you might be able to find a parts store willing to loan you a 2 jaw puller, but if not they generally run 30-35 dollars....DO NOT ATTEMPT THIS REPAIR IF YOU DO NOT HAVE A REPAIR MANUAL THE LISTS THE CORRECT TORQUE SETTING FOR THE TIE ROD ENDS. if the bolt isnt torqued propperly, a) your alignment will be off and b) you run the risk of snapping the new tie rod end.

May 03, 2010 | 1999 Pontiac Bonneville

3 Answers

Can i replace a tie rod {inner} on a 94 ford mustang , drivers side without taking off rack and pinion. I need to get a roll pin off the inner tie rod and thats the problem it looks pressed in not set...


Real simple, assuming you know how to take the outer tie rods off. You have to take the clip that holds the plastic boot on off, then slide back the plastic boot, and you'll be able to unscrew the whole inner tie rod assembly. The hardest part of the whole process is installing the new ones to the exact settings of the old ones

Mar 13, 2010 | 1994 Ford Mustang

4 Answers

How do I replace the upper ball joints in my 2002 Ford Explorer?


The upper ball joints are replaceable without replacing the control arms. Use Moog K80008 ball joints and a ball joint press.

Jun 25, 2009 | 2002 Ford Explorer

1 Answer

How do i change outter tie rod


Prepare your tie rod and install the grease fitting provided with it. 1. Jack up vehicle and secure on jack stand 2. Remove wheel 3. Turn steering wheel so that access is best to the tie rod assembly. 4. Loosen jam nut on tie rod.Do not disturb or turn this more than what is needed to make it loose from the tie rod as this will be your rough reference point and at least close when installing new tie rod. 5. Remove cotter pin from castle nut where tie rod attaches to spindle assembly. 6. Remove castle nut 7. Remove tie rod from spindle assembly - Free with a hammer striking it on the castle nut shaft to drive it out of the hole. 8. un-thread tie rod from tie rod shaft holding the shaft still with vice grip or other pliers. 9. Install tie rod on shaft until it meets the jam nut. 10. Insert tie rod to spindle, tighten, and install new cotter pin in castle nut. 11. Tighten jam nut 12. Grease tie rod assembly 13. Install wheel and have aligned. Do not skip having this aligned regardless of how it drives, post repair as tie rods absolute length can vary from manufacturer to manufacturer. Your final alignment will not be accurate until it is set on a rack with an alignment machine.

Jun 04, 2009 | 1999 Ford Windstar

4 Answers

2001 Dodge Caravan outer tie rod how to install it macking noice and shold i change stiblizar too


loosen nut on tie rod..22mm wrench,remove nut from tie rod end..18mm socket,hit side of knuckle with hammer to seperate tie rod end..unscrew tie rod end from tie rod..reverse procedure to install..you will to hold down on tie rod end to keep stud from spinning

Mar 16, 2009 | 2001 Dodge Caravan

2 Answers

Tie rod problem 98 Dodge


There is a tool that you can use that will make it easier for you. To get to the tie rod end, remove the wheel and take the outer tie rod end loose from the hub. You will have to use a hammer and hit the socket where the end goes into the hub to free it up. Once you have the tie rod loose from the hub, loosen the nut behind the outer tie rod end. Count the revolutions as you unscrew the outer end off and write te number down so you will know how far to put it back on. This will save your alignment. Now, the end that is still there is your inner tie rod end. You will have to undo the bellows boot to get to the nut. The tool will slide over the end and secure onto the nut. Now you just unscrew this and replace with you new inner tie rod end.
Please remember to rate this fix.

Feb 16, 2009 | 1998 Dodge Grand Caravan

2 Answers

How to change an inner tie rod end on a honda civic 1.5


you must remove or slide the inner tie rod boot outward on the rod and then thread the tie rod out of the steering rack. there is a section of the tie rod on the inside of the ball joint that has flat spots to get a open end wrench onto. to check your tie rods, simply jack the wheel off of the ground, grab the either side of the tire, and wiggle it towards and away from you. if you feel any play at all the tie rods must be replaced. also a god indication is when the front tires start to wear excessivly on the inside or outside edges.

as for the cv axle, it has a retainer ring on the end of the splined shaft. all thats reqired is to seat the splines in the transaxle (transmission) and the tap (shouldnt take too much) the outer end of the axle with a mallet or hammer. it will pop into place.

if you have any questions email me at thadoggma420@hotmail.com

Oct 03, 2008 | 1988 Honda Civic 2 Door

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...