Question about 1991 Jeep Wrangler

2 Answers

1993 Wrangler 4.0 Randomly My clutch pedal will not go in.

I Have a 93 YJ and just last night i started to have problems. I'm going down the rooad and o want to switch gears but the clutch will not depress. if fells liek there is a brick under the pedal. If I wiggle the stick around and try to force a gear the clutch pedal eventually releases. Whats the deal?

Posted by on

  • questcleaner Dec 22, 2008

    I fixed it i had to put in a new master and slave cylinder.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I HAD THIS PROBLEM IN MY 93 YJ, TURNED OUT TO BE AN INTERNAL FAILURE OF THE ACTUAL CLUTCH MASTER CYLINDER ITSELF (THE ONE NEXT TO THE BRAKE MASTER CYLINDER) IT HAS A "PISTON" TO ACTUALLY PUSH THE FLUID DOWN BELOW TO THE THROWOUT BEARING. AND IT WOULD GET JAMMED IN THERE. I REPLACED THE WHOLE UNTIL FOR $60 I BELIEVE AND HAVENT HAD A PROBLEM SINCE.
BEST OF LUCK

Posted on Mar 26, 2013

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 319 Answers

I can't remember if that year has a clutch master cylinder or not. Check to see if it does, it will be next to the brake master cylinder, and look like a single round silver dollar sized vesle. To the left of your brake master cylinder. check if its bone dry, if so refill it.

if this is not the case and it does not have a master cylinder, you need to check your clutch out.

Posted on Dec 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I can't depress the clutch pedal


Can't push clutch pedal in - JeepForum.com

www.jeepforum.com > ... > TJ Wrangler Technical Forum

Dec 11, 2010 - 7 posts - ‎3 authors
Driving home last night and the clutch pedal falls to the floor. ... Forums > TJWrangler Technical Forum > Can't push clutch pedal in ... Comes back up but then Ican't push it back in at all, even trying to stand on it, won't budge. Clutch locking up?
10 posts
Jul 30, 2011
Clutch Pedal Frozen Need tech help
10 posts
Sep 8, 2009
Clutch pedal stuck in the up position.
6 posts
Jul 26, 2009
Any more to clutch adjustment?
10 posts
Nov 28, 2008
More results from www.jeepforum.com

1998 Wrangler Sahara - Won't go into gear! Help please! - Jeep ...

www.wranglerforum.com/.../1998-wrangler-sahara-wont-go-into-gear-h...

Oct 5, 2010 - 22 posts - ‎7 authors
With the engine off, i can push the clutch in, and shift through all the gears ... to move - the clutch isn't disengaged even with the pedal fully depressed. .... Also, trying to bleed the system, can't find the bleeder screw. .... 1991 Jeep Wrangler Stuck In Gear? jeffasel, YJ Tech Forum, 5, 10-19-2010 09:42 AM. Getting difficult to push clutch pedal down, HELP
20 posts
Jun 17, 2011
How to bleed my clutch Be spacific.
11 posts
Feb 26, 2011
Clutch Problem?
30 posts
Jun 22, 2010
My Clutch Problems and How I Resolved Them
8 posts
Jan 28, 2009
More results from www.wranglerforum.com

Jan 13, 2016 | 1991 Jeep Wrangler

1 Answer

Reasymble 1993 jeep wrag collumnngler steerin


ah.
how to reassemble the 93 jeep wrangler steering column?
someone else took it a part?
read the FSM. free.
YJ JEEP
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Feb 17, 2014 | 1993 Jeep Wrangler

1 Answer

91 jeep wrangler YJ shifting problems


do you mean it wont go into gear ? if so what gears ? it could be the clutch going out , if the pedal is soft or easy to push down than it probably needs a clutch. next time it wont go into gear try pumping the clutch or putting it from 2nd to 1st or what ever gear it has problems with

Dec 18, 2013 | Cars & Trucks

1 Answer

Jeep YJ stalls while clutch is depressed


thrust bearings are bad and the flywheel is moving out of range of the crankshaft sensor, or the crankshaft sensor is sitting too close to the flywheel.

Mar 12, 2013 | 1998 Jeep Wrangler

2 Answers

I havent been having any problems but when I try to start my jeep,it's not turning over at all.I have lights..I had the battery checked at a Parts store and it's good.It won't boost off but I can push it...


You should have a switch on the clutch pedal under the dash. easy to test,,,just jump across it and see if it starts (only with trans in neutral and your foot on the clutch because it can start in gear when jumped) You also have a relay in the power distribution center and a fuse as well. Relay test is simple...most of the relays are the same so just swap positions. You should also check to make sure power is getting to the starter...12v at main connection and 12v at the small connection with the key turned to the start position (again in neutral and at least have the brake on) If you have power at the starter, likely it has failed. Don't forget...ignition switch needs to be working as well.

Sep 27, 2010 | 1993 Jeep Wrangler

2 Answers

I had a fire in the engine of my 93 yj 4 cyl i need to replace the engine wiring harness can it be replaced with the wiring harness from jeeps of other years


I would really try to get the same year and motor as you have. There is some much that often changes from year to year, and engine to engine.

Mar 16, 2010 | 1993 Jeep Wrangler

1 Answer

1995 Jeep YJ with a new engine. No power going to coils.


sounds like you are working on a car FSM free?
why do that?
95 YJ
early wrangler
i have 95 yj fsm and 93, the 93-95 are a year class range.
very simular.
here is a free 93 fsm with full schematics in chapter 8w
wiring chapter, clik
pdf 76 is page YJ 19 actual
and as you can see its cave man simple 2 wires.
minus to ECU ignitor driver. transistor (inside ecu)
and
+ goes to
a142 sheet 5 (pdf 62)

im not sure what part A<B<C is, a fuseable link, is my guess
and is blown. but that be a bingo spot for sure.
the full manual is there.
see spark chapter.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

posted over 100 times, this link, its not new.

Feb 13, 2010 | 1995 Jeep Wrangler

1 Answer

1991 jeep wrangler


yes it could be also check the fluid level!

May 14, 2009 | 1991 Jeep Wrangler

1 Answer

1990 yj manual trans will not go in any gear


possibly hydraulic clutch fluid? i have a 2002, not sure if the 93 has hydraulic clutch fluid but you might just want to check it to be safe good luck

Sep 06, 2008 | 1993 Jeep Wrangler

Not finding what you are looking for?
1991 Jeep Wrangler Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...