a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
They are very common for the door latch actuator assembly. Usually it starts when one particular door stops locking or unlocking. The lock rod will only partially go up or down, then gradually stop all together. The actuator used to be a separate component, however now it is integrated into the entire latch assembly. It most likely is the problem and will need replacing. If its just an issue that your key fob doesn't work anymore try replacing the battery in the fob. Then hold the lock and unlock buttons for 7 - 10 seconds to re-synchronize the transmitter.
You can possibly not have the correct key and the door lock caqn be frozen with ice. The lock it'self might not be frozen but the locking mechcaizem may be. Try different doors as all the door locks will reset the alarm even the hatch. Just unlock it twitce and all the doors should unlock and the alarm reset. A locksmith can open the door for you if you think you have a key problem and once oped the battery can be disconnected the doors clsed with the window down and the key in the on position and then connect the battery and the computer will think the car is already on so the alarm will not be on and then you can turn the car to run and start it and get in and go.
try this,reconnect the new battery and then lock/hold the key over for 30 secs,then unlock/hold the key over for 30 secs,the windows will go down if its trying to reset.then lock/hold over the key again,then press/hold the unlock button on the remote,this will fully reset the cental locking/alarm/immobiliser system.
Lot's of things can make it do it but with the drivers door window open. close and lock all the doors. ( said close the doors as in open them and close them back and make sure they close good ) Once all locked up unlock the drivers door with the key twiced once unlocks the door the second time it unlocks all the doors and the thrid time it'll unlock the hatch too. If it does'nt and the alarm is still going off open the hood and close and lock all the doors again. disconnect the battery, ( the alarm will certainly stop then), With the battery disconnected and all the doors closed and locked, put the key in the ingtion and turn it to run ( nothing will happen as the battery is disconnected ) This next part is important. The batterycables should be clean anyway but if their not they need to be clean for the next operation. With them clean put the positive on first and tighten it down now put the negiative onlike you mean it ( don't let it bounce and connect it. The alarm should'nt be going off as the car has the key on. Reach in and start the car ( I did'nt say open the door). with it running it should'nt be alarming either. Turn the key off and remove it them open the door and get in and restart the car itshould be back to normal.. Most of the time one of the door switches said to the computer that it was opened as it was supposed to be locked or it was opened after it was supposed to be locked and you left.
You might just need to reset it. Roll the drivers window down and close all the doors. Lock all the doors with the key ) turn the key to lock twice, The electric locks should lock all the doors. wail a few minutes and unlock and open the trunk with the key. relock the truck or just close it. unlock the drivers door with the key, twice. all the doors should unlock, get in and start the car. Now this does'nt always work. If it does'nt we'll make the system think it's running. Close and lock all the doors. open the hood and disconnect the battery, one ccable will be fine. wait a few minutes. Reach in though the open window and turn the key all the way on. Don't open the doors, go around and connect the battery hard so it does'nt jump or skip. Reach thought the window and start the car/ once it's running. turn it off remove the key and unlock the door from the inside and open the door ( as if you were inside.) get in and start the car and everything should be back to normal.
allright,thank you for consulting fixya.com. try to reset your computer in car by disconnecting the positive cable on the battery for 10mins. but make sure your vehicle has not been vandalized 1st. inspect the key switch please. if all good there, look at your radio system, if all good there, reset the sysytem by disconnecting the pos. side terminal on the battery for the 10mins please. when you reconnect the battery, you may need to manually lock the doors with your key. lock the doors for 2mins then unlock the doors with key and then attempt to start the car.this should reset the alarm. hope this helps and thank you for choosing fixya.com
Just a quick note once you hook the battery back up try locking it and unlocking it from the drivers door, if that fails you might try the passenger door. I know on some chrysler products you have to lock and lock again to arm and unlock to disarm. I hope this helps. Thanks, Joey
conect back the battery close all doors and windows driver door insert the key unlock the door one time and hold the key until window goes all way down then turn key to lock the door hold to lock position until windows go up if no stop repeat one more time right way without taking the key out , hope this help.
try a hard restart, if that doesnt work then you need a new rear window motor. for the hard restart all you have to do is disconnect the battery cables and touch the positive and negative together for about 8 seconds. if that fails then a new motor it is.