Question about 1993 Chevrolet Corsica

1 Answer

Locating the furn signal flasher on 1993 corsica

My turn signal and hazard flashers do not work. need to find location of both. dont have service manual for a picture

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

First check all light bulbs.. they are on the steering column. have to remove the plastic under column to get to.

Posted on Oct 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 ford ranger blinkers not working


first check fuse if fuse okay the turn signal lights dont work and flasher dont work problem could be faulty turn signal switch or faulty hazard flasher.which locate on fuse panel under instrument panel to the left of the steering column.

Nov 28, 2011 | 1993 Ford Ranger SuperCab

1 Answer

I don't know where the signal light flasher is located the signal lights don't flash


Your vehicle has 2 flasher relays. One for the turn signals and one for the hazard lights. The turn signal flasher relay is located on the drivers side, under the dash, mounted on the drivers (Left) side of the steering column. The hazard flasher is mounted on top of the steering column. Do not get them mixed up.

Aug 12, 2011 | 1991 Chevrolet Corsica

3 Answers

Turn signals dont work on 1993 skylark. all bulbs are good. hazard lights blink fine. turnsignal dash light stays green and doesnt blink


There are 2 separate flasher relays. 1 for the turn signals and one for the hazards. I believe you have a bad flasher relay for the turn signals. The location of that is in the front seating area on the drivers side, under the dash on the drivers side of the steering column, mounted on support bracket. I provided a picture of what it should kind of look like although the picture I gave you is an aftermarket one so the color and such may be a little different but will look the same. Don't get it mixed up with the hazard relay which is located in the front seating area on the drivers side under the dash above the kick pane lmounted on top of the convenience. I am almost 100 percent sure the flasher and hazard relay are the same so if you want to just swap them out in order to have turn signals that should work. You won't have hazards however. I hope this helps you and good luck.


clifford224_215.jpg

May 07, 2011 | 1993 Buick Skylark

1 Answer

Where is the turn signal flasher located


1992 Chevrolet Corsica 2.2L SFI OHV 4cyl.

Front seating area, driver side, under dash, mounted on top of steering column
Application: Hazard flasher

Front seating area, driver side, under dash, mounted on driver side of steering column
Application: Turn signal

Hope helps (remember to rate and comment this).

Sep 30, 2010 | 1992 Chevrolet Corsica

1 Answer

Turn signals dont work


For 1993 Oldsmobile Cutlass Ciera 3.3L FI OHV 6cyl. you have two flasher units, one for Hazard Light and one for Turn Signal...

The hazard flasher is located in the convenience center, under the dash, on the left side kick panel. The turn signal flasher is installed in a clamp attached to the base of the steering column support inside the car. In all cases, replacement is made by unplugging the old unit and plugging in a new one.

Hope this help (remember comment and rated this help).

May 12, 2010 | 1993 Oldsmobile Cutlass Ciera

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

1 Answer

Haz flashers wont work but blinkers do


There are 2 seperate flashers 1 for turn signals and 1 for hazard.The hazard flasher is located in the convenance center the turn flasher in the fuse box. Also seperate fuse's for each. One battery circuit for hazard Ignition for turn signals.Check fuse for hazard,if good try swapping in the turn signal flasher and see if hazards work.They use the same flasher unit.

Aug 20, 2009 | 1993 GMC Safari

1 Answer

Need to know where the flasher relay fuse is located on a 1993 Chrysler New Yorker.



The fuse panel is located under the instrument panel to the left of the steering column.

The hazard and turn signal flashers are located on the relay module.

HOPE this HELPS EASY way to DETERMINE witch one is for turn Signals is to Turn ON HAZARD FLASHER and this shows that the other one is for turn Signals PLEASE REMEMBER TO RATE ME MOST FOLKS DONT remember to. THANK YOU AND GOOD LUCK

Mar 29, 2009 | 1993 Chrysler New Yorker

1 Answer

I am trying to find the turn signal flaher unit on a 1988 corsica


The turn signal flasher should be located on the fuse box under the drivers side dash.

Jan 30, 2009 | 1993 Chevrolet Corsica

1 Answer

Locating the turn signal flasher on 1993 corsica


The turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

Dec 03, 2008 | 1993 Chevrolet Corsica

Not finding what you are looking for?
1993 Chevrolet Corsica Logo

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...