Question about 2002 Mitsubishi Lancer

1 Answer

Timing mark timing belt broke and repalcing with new one

Posted by on

  • yadayada
    yadayada May 11, 2010

    what is the question?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 54 Answers

Inside of the top gear there is a hash mark, you need to turn the gear so that the hash mark is top center. (you need a second person to help you for the next step.) You then have to take the first spark plug out and stick a long screw driver inside of the hole. You then have to turn the bottom gear until the first cylinder comes all the way up. You then put the new belt on the car without moving the two gears.

Posted on Dec 03, 2008

1 Suggested Answer

queencreekmx
  • 2 Answers

SOURCE: timing belt broke on a 95 ford ranger.new belt

you have to line up the two marks on the gears and set the tension to the correct setting. then check the marks again. trial and error. i just did my timing belt on my ranger haha

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing belt marks on 1.5 in picture


did the belt break or is this regular maint??? it is an interfearance
head , if it broke the valves will all be bent end of that story.
if you have it apart be very careful turning things (you will hit valves) if old belt is still on ,take a paint marker , mark the belt and cam gears and the crank with one dot one the belt edge and gear face. remove belt ,lay new belt edge to edge and transfer marks exactly onto new belt slip new belt onto cams n crank verify everything is matched to old marks if tensioner is adjustable dont make it to tight or it will "sing" this way if it was running when you shut it off it does not matter where the timing belt marks are because nothing should be out time.

Mar 06, 2015 | 1999 Daewoo Lanos

2 Answers

How do you put a timing belt back in time after it broke?


Well, hopefully the valves were not damaged when the belt broke, If no valve damage was done, get the engine/crankshaft to top dead center, line up camshaft sprocket to timing mark and install belt around pulleys, gears, replace water pump if needed, tension belt if no automatic tensioner is used, try to start to see if it runs and hopefully it will. Might be time for an engine if valve damage was done.

Jul 14, 2014 | 1992 Chrysler Lebaron

1 Answer

HYUNDAI H100 2.6 DIESEL TIMING DIAGRAM


I have a Toyota Town Ace diesel van, the timing belt broke and I need step by step help how to install new timing belt - timing marks diagram.

Jun 24, 2012 | Cars & Trucks

2 Answers

Timming belt broke from water pump broke while driving car put new water pump on n timming belt but car doesnt start right plus shakes doesnt sound right 2001 neon dodge


Sounds like timing belt not on correctly. Check timing marks are aligned correctly when installing timing belt. This vehicle should have 2-3 marks to be aligned when installing belt.marks should be on cam gear/ crankshaft gear and intermediate shaft if engine is equipped with it.

Sep 10, 2011 | Dodge Neon Cars & Trucks

1 Answer

Timing is off


If your timing belt broke chances are you have bent valves and damaged pistons. The vehicle may never start unless you repair the engine damage.

May 21, 2010 | 1997 Subaru Legacy

1 Answer

Timing belt broke on a 95 ford ranger.new belt


you have to line up the two marks on the gears and set the tension to the correct setting. then check the marks again. trial and error. i just did my timing belt on my ranger haha

Feb 18, 2010 | 1995 Ford Ranger Supercab

1 Answer

When installing timing belt, where do I place the marks on the cam and the crank?


Go to any autoparts store and get a manual for your vehicle. Installing a timing belt incorrectly can cause major engine damage. If this belt broke while driving you may already have bent valves. Timing belts should be repalced every 60,000 miles.

Oct 25, 2009 | 1996 Plymouth Voyager

2 Answers

Timing belt


not to worry. if timing belt broke your engine is fine. it is an overhead cam engine. although there is a good chance depending on your motor size. that one of the composite sprockets the belt runs on broke also. it is common.

Jun 26, 2009 | 1999 Mercury Cougar

1 Answer

The timing belt broke on our 95 elantra and im fixing it how cam


you need to get a diagrm . try googel . timming marks for your car . if the belt broke while driving more then likley there is engine damage

Jun 04, 2009 | 1995 Hyundai Elantra

1 Answer

Timing belt


you will need to rull the timing cover off if belt has not spun or broke remove belt and install new one if belt has spun or broke you will need to line up timing marks on cams and crank and install belt

Oct 04, 2008 | 1996 Chrysler Concorde

Not finding what you are looking for?
2002 Mitsubishi Lancer Logo

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...