Question about 2002 Audi A4

1 Answer

No security system beep when vehicle is locked

When I lock the car security system does not beep to confirm that the car has been locked. I verified that all doors, hood, and trunk are locked. Security system also does not sound when I press panic button on the remote. Also, just noticed that security system LED on the driver's door is now solid after vehicle is locked. It used to blink when security system was ok.

Posted by on

  • 1 more comment 
  • meras20 Dec 12, 2008

    You have some security related buttons on the lower side of the drivers door, I cant remember in what order you have to press them but thats how I got rid of my problem.

    Also today my drivers door started not to respond, all the doors get locked, but the driver door does not lock, cant lock it with the key either...any ideas???

  • Anonymous Mar 13, 2014

    security system keeps locking and unlocking door while driving

  • Anonymous Mar 25, 2014

    Security ramdomly beeps while driving

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check to see if your "interior cabin lights" fuse isnt blown it is a 15amp fuse one of the top two rows in your fuse box. i have a 2002 A4 avant and when that fuse blows my security beep doesnt make any sound but the doors lock.

Posted on Dec 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Doors dont lock with secrity fob


The receiver for the fobs is located in the rear hatch, and it needs to be reprogrammed to the fobs. Try the following procedure;

1. Close all the vehicle doors.
2. Insert the ignition key into the ignition lock cylinder.
3. Press and hold the door unlock switch.
4. While holding the door lock switch in the unlock position, cycle
the ignition ON, OFF, ON, OFF.
5. Release the door unlock switch. The doors will lock and unlock to
confirm the program mode.
6. Press and hold the LOCK button and the UNLOCK button
simultaneously on one transmitter. After a delay of approximately 15
seconds, the doors will lock and unlock to confirm the programming of
that transmitter.
7. Repeat the previous step to program up to four transmitters.
8. Turn the ignition switch to the RUN position in order to exit the
keyless entry transmitter mode.
9. Operate the transmitter functions in order to verify correct
system operation.

Sep 05, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

Press button on key and nothing happens doors wont open or lock on my peugeot406 i have had my battary checked on fob it ok


Synchronization
When
Key battery replaced. If buttons operated repeatedly while vehicle out of range and system becomes inoperative.
How
Switch ignition ON. Press and hold lock button Fig. 1 [1] for 10 seconds. Switch ignition OFF. Remove key from ignition switch. Wait 5 seconds. Synchronization procedure complete. Confirm synchronization has been successful by locking, double locking and unlocking vehicle. Repeat above procedure to synchronize any remaining keys.
Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys. Obtain owner's vehicle security card. Replacement keys can only be programmed using diagnostic equipment.

Mar 26, 2011 | Peugeot 405 Cars & Trucks

1 Answer

I have a 98 Nissan altima gxe and my alarm won't honk when I lock the car but the lights go off when I lock it and Wen I take the alarm off no honk or lights go off Wat can I do


holdboth the lock and unlosk buttons on your remote simultaneously for about five seconds until the lights flash and horn chirps.that should do it.if not i believe these models used a separate horn for security system.possibly fuse for this horn is bad or the horn itself is bad.to see if this horn works lower drivers window.stand outside vehicle and lock doors with remote.wait about a minute and reach in window and MANUALLY unlock and open door(do not use power door lock button)this should cause the system to activate...horn should beep and headlamps should flash.if horn beeps try my first suggestion.if it doesnt beep and just the head lamps flash check fuses and horn for security system.

Feb 21, 2011 | 1998 Nissan Altima

1 Answer

Need help programing my keyless remote for a 2000 alero. This is what is on the back, GM/UTA 25665575, FCC ID. KOBUT1BT,Canada 1983 101 393 It has four buttons top two are left pic of lock, Right pic of...


1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.



Thank you for using Fixya and good luck

Mar 17, 2010 | 2000 Oldsmobile Alero

1 Answer

How do you program the keyless remote on a 2002 Intrigue?


1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode.


Good luck and thank you for using Fixya

Mar 09, 2010 | 2002 Oldsmobile Intrigue

1 Answer

2000chevy malibu keyless entry problem need help


1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 22, 2009 | 2000 Chevrolet Malibu

1 Answer

How to program key fob. I have the fobs.


Transmitter Programming Procedure
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Good luck

Jun 25, 2009 | 2002 Chevrolet Tahoe

2 Answers

How do u program a new key fob for a 2004 chevy Malibu


Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the DOOR unlock switch.
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation

Jun 04, 2009 | 2004 Chevrolet Malibu

1 Answer

How can i program the key less?


  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation.

Dec 03, 2008 | 1999 Chevrolet Astro

1 Answer

Automatic door locks will not work


Probably the door actuator - a part inside the door that activates the lock, particularly if neither the interior lock switch or the remote do not lock the door.  Once the doors lock the horn will beep again - the lack of beep indicates the vehicle is not secure.

Nov 17, 2008 | 2004 Honda Pilot

Not finding what you are looking for?
2002 Audi A4 Logo

970 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

63801 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13215 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...