Question about 2008 Suzuki SX4

1 Answer

16V output need a output for satellite localizator in the rear luggage space

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Are you looking for 16 volt, or 12 volt, as in battery power??
If 12 volt there is already wiring for the 12 power outlet behind the passenger sidewall in luggage area of the crossover.
To find instructions on how to do it, just go to www.sx4club.com and search for the solution there. It's really simple, took me less than 5 minutes, the part numbers are available at the site, my cost was around $20 cdn.

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Battery dead. how can I get trunk open.


You can't unless it has a key hole. If you put jump leads on the battery or connect a battery charger it will open straight away.

May 01, 2016 | 2008 Ford Taurus SEL

1 Answer

Hi I have 1998 Daewoo Lanos Hatch back I am trying to located the spot where I can put a baby bolt in ? I cannot find it ! Thanks Tanya from Brisbane


In the 1999 Lanos Hatch, there is no bolt. There is a link where you can attach the standard clip. It's located in the rear centre of the luggage space. feed it over the back seat, in between the seat & the folding cover & clip in accordingly. You may need to buy an extension to reach it. Hoping this helps.

Mar 04, 2011 | 1999 Daewoo Lanos

1 Answer

Is there a rear seat release on a 94 accord


I believe this procedure applies to your 94 Accord:
With your hands, press down on the seat cushion where it meets the seat back. Locate the retaining bolt(s). Some models retain the seat with one bolt in the center; others use two, evenly spaced left and right.
Remove the retaining bolt(s).
Lift the back (toward the rear of the car) of the seat bottom upwards while rotating it toward the front of the car.
Disconnect the hooks at the front edge (during the rolling motion) of the seat and remove the seat bottom.
Remove the carpet (in the luggage compartment) from the rear of the seat backs.
Remove the seat back mounting bolts from the luggage compartment side.
Lift out the seat back.
If the rear side bolsters or pads are to be removed, remove the lower mounting bolt, then push upward to free the hooks.
Hope this helps you.

Dec 21, 2009 | 1994 Honda Accord

1 Answer

Remove backseat of honda accord 1991


With your hands, press down on the seat cushion where it meets the seat back. Locate the retaining bolt(s). Some models retain the seat with one bolt in the center; others use two, evenly spaced left and right.
Remove the retaining bolt(s).
Life the back (toward the rear of the car) of the seat bottom upwards while rotating it toward the front of the car.
Disconnect the hooks at the front edge (during the rolling motion) of the seat and remove the seat bottom.
Remove the carpet (in the luggage compartment) from the rear of the seat backs.
Remove the seat back mounting bolts from the luggage compartment side.
Lift out the seat back.
If the rear side bolsters or pads are to be removed, remove the lower mounting bolt, then push upward to free the hooks.
Hope this helps you.

Oct 17, 2009 | 1991 Honda Accord

1 Answer

Remove rear seat from 1994 Dodge Spirit


there is a hidden spring bar retainer on each side of the seat that must be pushed in and then pulled up to release,

Sep 08, 2009 | 1994 Dodge Spirit

1 Answer

Need to replace right brake light. How do I remove and replace trunk lining to get access withou doing damage to the liner? What is the correct lamp?


Remove the luggage compartment rear trim panel. Detach luggage compartment side trim panel. Detach the rear lamp assembly bulb holder. Remove the rear lamp assembly. To install, reverse the removal procedure.

Aug 03, 2009 | 2003 Jaguar S-Type

1 Answer

Right rear signal light needs replacing


you need to remove the lamp assembly to replace the bulb. here is the procedure:

Rear Lamp Assembly —Sable Four Door Removal and Installation
  1. Remove the luggage compartment scuff plate.
  1. Pull back the luggage compartment carpet.
  1. Disconnect the rear lamp assembly electrical connector.
  1. Remove the nuts.
04eb075.gif
  1. Remove the rear lamp assembly.
    1. Pull the lamp assembly away from the body.
    1. Disconnect the rear lamp assembly bulb connectors.
    1. Remove the rear lamp assembly.
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent water from entering the luggage compartment, make sure the rubber grommet is fully seated.
    To install, reverse the removal procedure.

Jun 25, 2009 | 2001 Mercury Sable

1 Answer

How do I replace a taillight lens on a 1991 Geo Storm?


Rear Turn Signal, Brake and Parking Lights


STORM COUPE
  1. Disconnect the negative battery cable.
  2. Lift the luggage compartment floor carpet toward the front of the vehicle and remove the spare tire cover panel.
  3. Remove the ten plastic retaining clips from the rear end trim panel.
  4. Disconnect the luggage compartment lamp electrical connector.
  5. Remove the luggage compartment trim panel and the rear end trim panel.
  6. Disconnect the rear combination lamp assembly electrical connector. Fig. 1: Rear Turn Signal, Brake and Parking Lights — Storm
84256028.gif
  1. Remove the seven nuts and the rear combination lamp assembly from the vehicle.
  2. Disconnect the rear combination lamp electrical connector.
  3. Remove the four bulb sockets from the rear combination lamp assembly and remove the four bulbs from the sockets. To install:
  4. Install the four bulbs to the sockets and install the four bulb sockets to the rear combination lamp assembly.
  5. Connect the rear combination lamp electrical connector.
  6. Install the rear combination lamp assembly to the vehicle and the seven nuts.
  7. Connect the rear combination lamp assembly electrical connector.
  8. Install the rear end trim panel and the luggage compartment trim panel.
  9. Connect the luggage compartment lamp electrical connector.
  10. Install the ten plastic retaining clips to the rear end trim panel.
  11. Install the spare tire cover panel and the luggage compartment floor carpet.
  12. Connect the negative battery cable.

Mar 21, 2009 | 1991 Geo Storm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...