Question about 1989 Ford Bronco II

1 Answer

Ford Bronco II standard tran. Has no 1st or 2nd gear.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 57 Answers

Replace the transmission fluid. I think those used ATF, but check to be sure. (if you made the mistake of using 80/90w drain it...those transmissions were not designed for 80/90w. gear oil)

Posted on Dec 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a flywheel on a 84 bronco 2 standard transmition


is the flywheel worn out or just the ring gear, (starter gear)
first remove the trans mission then unbolt the flywheel, and replace
if only replacing the starter ring gear, use a soft hammer and bump it as you rotate the flywheel until it comes off, if the back side looks good heat it in the oven to 350 degrees and with gloves on run out and put it on the flywheel, it will go on easily, just hold it all the way on against the edge it rests on and turn it about 1/3 turn and hold for about 15 seconds and that's it, it will not come off unless you beat it off again

Mar 23, 2015 | 1984 Ford Bronco II

1 Answer

Transmission shift problems


you need to change your clutch slave cylinder if ur truck is manual gear

Nov 24, 2013 | 1996 Ford Bronco

1 Answer

1988 ford bronco ii- It wont go into overdrive, reverse works fine and any time I go from park or reverse to 1st, 2nd or Drive and press on the gas it just revs until finally catching and burning out or...


sounds like it has been sitting to long, gp tp a parts house and purchase trans x for trans, it will help the throttle body in the trans to free up valves

Aug 26, 2013 | Ford Bronco II Cars & Trucks

1 Answer

1995 Ford Bronco engine dies when shifted into drive but runs in reverse or 1st gear


Could be fuel filter,air filter,tune up,wires,coils.low idle too low.

Jun 13, 2013 | 1995 Ford Bronco

1 Answer

1988 Ford Bronco II shifts into 1st and 3rd gear hard and some times pops out of gear.


Sounds like the first and third gear synchronizer is worn out.
You might want to talk to a transmission shop to confirm.

Feb 28, 2013 | 1988 Ford Bronco II

1 Answer

****** wont shift to drive,the trans get 1st,2nd,and reverse


standard or automatic transmission. and does it do it when driving, or is the shifter bad at a stop.

Sep 28, 2011 | 1985 Ford Bronco II

1 Answer

Won't come out of 4 low and won't change from 1st to 2nd gear


try checking your auto trani fluid... and with the 4 wheel drive try puting ti in nuteral and if the doesnt work try puting it in reverse and back up after taking it out of 4 wheel drive.

May 24, 2009 | 1996 Ford Bronco

2 Answers

A4LD 4X4. trans. wont engage into gear


It grinds just sitting still? Will it do it with the transfer case in neutral or 4x4?

Mar 14, 2009 | 1989 Ford Bronco II

1 Answer

1988 Bronco II transmission pop out of 1st gear


there are dent and brass balls that are in your transmission and are used to hold the shifter into each gear when it starts poping out of that means that those dents and brass balls are worn down and i would suggest getting the transmission rebuilt.

Dec 16, 2008 | 1988 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...