Question about 2006 Chevrolet Cobalt

2 Answers

I need to remove door panel on 2008 Cobalt

I want to remove the door panels so I can tint the windows, I am afraid to just pull the panel like on older model cars. The door is all plastic so I could use help!
Thank You
Tom

Posted by on

  • Papidemio477 Dec 07, 2008

    I have a 07 cobalt LT and I want to remove the door panel to replace some speakers. How would I do that?

  • Anonymous Feb 13, 2009

    how do i remove the manual window crank, to get the door panel off?

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Director Badge:

    Uploaded 100 video answers.

  • Expert
  • 159 Answers

Here's a How To video that will show you how to remove the door panel from a 05-10 Chevy Cobalt.

Hope this helps out,
1aauto.com

Posted on Jul 12, 2012

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 54 Answers

There are about five or six screws on the panel, the rest of it is snap on. You will have to pull the door panels off the door with a flathead screwdriver.

Posted on Dec 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove the drivers side door panel to fix the window


YOU NEED CLIP REMOVAL TOOL TO REMOVE WINDOW CRANK HANDLE.YOU NEED DOOR PANEL FLAT TOOL REMOVE DOOR PANEL HATE TO SAY DOOR PANEL HAS AT LEAST 8 CLIPS LOCATIONS 4 CLIPS AT THE BOTTOM PANEL 2 CLIPS ON BOTH SIDES DOOR PANEL. YOU HAVE TO REMOVE 2 SCREWS HOLDING DOOR PULL CUP.YOU HAVE RELEASE CLIP BEHIND DOOR HANDLE USING TRIM TOOL.IF YOU HAVE TROUBLE GETTING DOOR PANEL OFF.HAYNES REPAIR MANUAL CAN HELP.

Oct 07, 2010 | 2004 Chevrolet Cobalt

6 Answers

2008 Cobalt - Front speakers not working and no audible turn signal. Both stopped working at the same time.


In my 2008 Cobalt, the front speaker in the driver door went inoperative - no turn signal noise, no warning chimes for door open with key in, seatbelt chime, low fuel chime, and of course, no music. All of those sounds come through the speaker. I switched the driver door speaker and the passenger door speaker, and now I have all of those noises back.

If you have manual roll down windows, you'll have to buy a special tool to remove a little clip that's behind the roller handle. This tool was included in a kit for about $7 that I bought at Harbor Frieght, but you might be able to find the kit at other auto parts stores. Google "removing window crank" and you should be able to locate a video that shows how to get it off.

Anyway, I switched the speakers and now we just don't have music coming out of the passenger door speaker, but at least we have all of the warning chimes and turn signal clicking noise again.

The dealer wanted almost $200 for a new speaker and to replace it (labor). Rediculous.

Jul 20, 2010 | 2008 Chevrolet Cobalt

1 Answer

How to fix door handle on chevrolet cobalt 2008


Have to remove inner door panel and is usually 2 bolts around 10mm that hold handle in, but the rods must be removed first and these rods are only held in place by a spring steel clip that just flips out off the rod at the handle end.
To remove door panel - look for visible screws under and around the edges and or handles, remove all these. If window is winding type a horse-shoe clip holds the handle on and can be pushed off with a screw-driver if you push the panel away from handle and look behind the handle.
Then take a putty knife and or butter knives and insert between door and panel to pop plastic clips from door then lift on panel to remove from window jam.  Be careful of wires and plugs after this.  Remove plug clips and place panel aside.  Remove plastic and sound-proofing if any in the corner near the handle and a 10mm 1/4" drive ratchet to remove bolts on each side of handle.
This is a general answer but should work for the Cobalt as well.
East Coast Canada Rocks!!
:))

Jun 09, 2010 | 2008 Chevrolet Cobalt

1 Answer

Passenger door removal for radio speaker access.


YOU NEED A DOOR PANEL FLAT TOOL AND WINDOW CRANK CLIP TOOL IF YOU DONT HAVE POWER WINDOWS. A HAYNES REPAIR MANUAL TO SHOW YOU HOW TO REMOVE DOOR PANEL.

Apr 04, 2010 | 2007 Chevrolet Cobalt Coupe

1 Answer

How to remove an exterior door handle Audi A8 2008


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can pull back the weather seal and disconnect the linkage and remove the bolts securing the outer door handle

Oct 06, 2009 | 2008 Audi A8

1 Answer

I need instruction on replacing the passenger side mirror on a 2008 chevrolet cobalt


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Sep 24, 2009 | 2008 Chevrolet Cobalt

1 Answer

Show me how to take of the inside door panel of a


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.

Sep 17, 2009 | 2008 Mazda MAZDASPEED MAZDA3

1 Answer

How to install the right mirror for accura MDX 2008


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then remove the bolts securing the mirror to the door

Sep 17, 2009 | 2008 Acura Mdx

1 Answer

Removing passenger door panel on chevy cobalt


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Jun 16, 2009 | 2006 Chevrolet Cobalt

1 Answer

Replacing side view mirror, pulling off side door panel.


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge


Feb 24, 2009 | 2007 Chevrolet Tahoe

Not finding what you are looking for?
2006 Chevrolet Cobalt Logo

690 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...