Question about 1999 Pontiac Grand Am GT

1 Answer

Front sway bar

Where is the front sway bar for a 1999 pontiac grand am gt located and how hard is it to fix

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 341 Answers

Should be behind the front wheels and is mounted to the control arms and the body . Most have sway bar links on the control arms, but some are mounted with clamps.If it is broken or the bushings are worn it is easy to fix. Just make sure you tighten the bolts with the car's wieght on the ground or the bushings will squeak going over bumps.

Posted on Dec 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loation off turn signal flasher on 1999 Pontiac GT and is this the same as hazard warning flasher


yes they are one in the same , look under the dash behind the fuse panel,, hard to locate,

Jul 16, 2011 | 1999 Pontiac Grand Am GT

1 Answer

Can I drive a Pontiac Grand Prix with a broken rear stabilizer safely?


By rear stabilizer, do you mean trailing arm or sway bar? If you have a busted trailing arm, I highly advise against driving. This is the bar that runs from the wheel hub transversely toward the front of the car and attaches to the frame. However, a busted rear sway bar, which runs transversely across the vehicle and runs along side the leaf spring, isn't as severe of an problem. You will just run into spongy turning issues.

Jan 27, 2011 | 1994 Pontiac Grand Prix

2 Answers

How much to change a oil pan gasket for 2001 grand prix 3.8 gt


If you want to repair the oil pan I would also check lower engine mount for leaking oil and cracks in anti sway bar near fitting's. This due to engine mount is oil filled. OEM sway bar is made of tubular steel and they crack easy. Replacement sway bar is solid steel. Here's the kicker. When they pull the lower frame to service oil pan. The engine mount and sway bar are attached to that frame. A honest mechanic should only charge for parts ($35 for mount and $100 for sway bar) and maybe a extra hour. My mechanic did all in 5 hours. FYI gasket is only $35 bucks. Good luck

Feb 26, 2010 | 2001 Pontiac Grand Prix

2 Answers

Replacing sway bar. cannot get new sway bar to propper position. how do i get it to fit propperly?


Your old sway bar made of tubular steel. New sway bar made from solid steel. You have a frame under engine the sway bar attaches too. This frame also supports your engine and trans mounts. Follow frame and there are 4 bolts securing same. Mechanic I watched supported engine underneath. Loosen back bolts though not removed. (please note sway bar has arrow that bar can only go in one direction) This maybe your problem. Attach bar to frame and fitting's. Best if you raise front end and remove both tires. Good luck

Feb 15, 2010 | 1999 Pontiac Grand Prix

2 Answers

Crack in left front portion of sway bar. Is it possible to weld? The crack is on the back side of the bar saw it when doing brakes and rotors. How much should I spend on a new/used sway bar if welding is...


my opinion would not to muck about with things like that and replace it with genuine parts that way you know it's ganna last price not sure but would not reconmend welding it don't play with your life when it could only cost like 300 to 400 to save your life

Oct 30, 2009 | 1997 Pontiac Grand Prix

1 Answer

How to change 1998 Plymouth grand Voyager front sway bars


unbolt the sway bar links from the control arms and the two brackets holding it to the frame. make sure if you jack it up jack up the front end. if you jack up one side and not the other and take the sway bar loose it will be loaded and could cause injury if not careful as long as both front tires are off the ground the sway bar will not be loaded and will be safe to deal with

Oct 19, 2009 | 1998 Plymouth Grand Voyager

1 Answer

Replace the torsion bar on my 99 Pontiac Grand Am


they do not use torsion bars on those cars.it is probably the sway bar you're talking about.if it's the front one they are pretty tough to change.you need to lower the front sub-frame to replace the sway bar.

Jul 30, 2009 | 1999 Pontiac Grand Am GT

3 Answers

Pontiac Grand Am Popping sound when the wheel is turned


sounds like a half shaft to me try turning in a tight circle and see which side it clicks on left or right
make circles in both directions

Apr 15, 2009 | Pontiac Grand Am Cars & Trucks

1 Answer

Front Left Sway Bar Link


The front stabilizer shaft (sometimes called a sway bar) is mounted to the top rear of the frame and to the lower control arm. The shaft is attached to the frame with clamps and rubber insulators and to the control arms with insulator links.

Try http://www.autozone.com/shopping/repairGuide.htm

Jul 08, 2008 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
1999 Pontiac Grand Am GT Logo

Related Topics:

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...