Question about 1984 Chevrolet Camaro

1 Answer

1984 Camaro Z28 Wiper switch wont work properly

I got a new,used colum and the wiper switch dcolor coad does not match , the old one worked then would not work a few days later If I had a switch diagram oof the switch operation, I could wire it properly, Im Dumb Founded

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 101 Answers

Hello I will take a picture of the Diagram and send it to yea I have a 86 Iroc z28 So i have a Haynes manual for yours as well for most of the f body's are universal. I need a Email or a way to send you the file?

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiper not working properly and guage panel lights not working properly


mine was both a bad wiper switch and wiper motor.
when my dash lights acted up, a new HL switch sorted me out fine.

Oct 04, 2013 | Chevrolet C1500 Cars & Trucks

1 Answer

The fuses are good put in new wiper motor but wipers still wont work


check for power both sides of fues and then at switch,most switches in steering colum have relays some switches make contact with earth so no power goes to then they just make the earth circet for the relay ie relay has power all the time when it is earthed the switch in the relay turn on and power to the wiper motor,but first check for power and earth at the wiper motor if you haven't already,that should have been before replacing motor

Aug 14, 2011 | Ford E-150 Cars & Trucks

1 Answer

How to remove wiper arm


Hello,

Please follow the steps below to remove or replace the wiper arm:
  1. With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
  2. Locate the mounting clips at the top pivot on the wiper blade
  3. Release the clip and remove the wiper arm
  4. Match the size of the old blade against the new blade to ensure proper fit and operation
  5. Reinstall the new wiper blade and recheck wiper operation
Hope this helped. Thank You for using FixYa!!!

Jan 19, 2011 | 2004 Lincoln Town Car

1 Answer

How to replace a wiper arm on 1998 chevy camaro Z28


i dont remember exactly on camaros, but if you dont see a nut on the wiper arm, then there is a plastic cap covering it. remove that with a screwdriver by prying off gently. and loosen the nut almost all the way off. now wiggle the wiper arm back and forth and up and down.. you might need a screw driver to pry from underneath with slight force. wiper arms are tricky. make sure you put it in the exact position you took it off from. sometimes you have to turn the wipers on and shut off the key to stop them if the hood is in the way,

Jul 18, 2010 | 1998 Chevrolet Camaro

2 Answers

How do i replace the wiper blades?


pick blade up and press the pins togethor and pull out and slide the new ones in recommend the rain x blades work really good

Nov 27, 2009 | 2008 Honda Civic

3 Answers

My wipers will go on, but wont turn off, unless i turn my car off, or my ignition switch back one notch, and turn it back on...1984 oldsmobile delta 88..The switch has been replaced..Is there a relay for...


the relay is built into the wiper motor its called the pulse contol module and comes with a new wiper motor. make the wipers come on and then get them to stay on while wiper switch is in the off position, then tap the wiper motor and see if it turns off, if it does then u need a wiper motor assembly and be careful opening the hood some wiper arms will contact the hood when the hood is open and the wipers are on

Nov 27, 2009 | 1984 Oldsmobile Delta 88

1 Answer

Installed new wiper arms on my 1984 camaro and now they wont go into the off position.


did you install them in the off position. this will affect where they stop

Oct 18, 2009 | 1984 Chevrolet Camaro

1 Answer

Wiper blades


go to any parts store and buy the blades they will change them fro free, and watch while they are doing it.

Jun 24, 2009 | 1995 Chevrolet Camaro

1 Answer

1984 camaro z28 gas gauge


float arm in the tank is either stuck or broken. its connected to the fuel pump assembly

Mar 25, 2009 | 1984 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...