Question about 1989 Mercedes-Benz 300-Class

1 Answer

Left running light is not working. how do I remove it in roder to replace it?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 84 Answers

Hello, Left what? The front you remove by opening the hood and look toward the headlight assembly near the fender. There you should see a white plastic knob about 1 1/4 " wide. Unscrew the knob until it comes all the way off then grab lens a pull toward the front.
The rear, open trunk and look for a plastic cover about 3"X12". Unscrew the two knobs, pull cover forward, and replace bulbs
I hope this helps
CYA, Gator241

Posted on Feb 06, 2009

  • Wally Wicker Feb 09, 2009

    Hello again, If you find this information to be correct would you please enter a "fixya" rating.

    Thanks, Gator241

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove studs from right rear of a 2003 ford explorer i just want to replace the studs


You have the tire off. So take the brake clapper off.then the roder should come right off. Lay the roder down and hit the bad stud with a hamer it should come out easy. Put a new one in the same way but from the back.

Feb 13, 2015 | 2003 Ford Explorer

1 Answer

How do i fix a shuttering problem in the left front side of my legnum


Check the roder it might have worn that. Would make it shutter

Feb 10, 2015 | Cars & Trucks

1 Answer

My brake, vsc, and trac off lights are on and they stay on when my car is on. I just replaced my roders and my brakes don't seem to be the problem, and i had an alignment and balance done on my tires not...


Disconnect your negative break battery cable enter the vehicle turn the key to the on position which is 2 clicks usually not to the start position just to the on position with your foot on the brake for 10 seconds release the break turn the key off replace the negative battery cable start the vehicle in the next 60 miles those lights will reset on the brain and you will have no are flashing lights no more beeping sounds if there's a beat

Jan 07, 2018 | Cars & Trucks

1 Answer

1994 jeep grand cherokee limited 4.0 running rough and very rich all the time


Is the inside of the engine components have been you replace or check?

Jan 12, 2012 | 1994 Jeep Grand Cherokee

2 Answers

I took my 96 geo prizm to a garage it sounded like it was running on 3 silinders they told me it only needed a tune up i changed plugs wires cap roder fuel filter still does not run right i brought it back...


what do you want to know? So they didnt check it very good, or just guessed the problem. After 2 days, they should KNOW what it is, not THINK. take it to a real garage..

Oct 17, 2009 | 1996 Geo Prizm

1 Answer

My abs indicator light will not go off


Check the abs sensors. Located on the spindles, by the braking system.

Jun 09, 2009 | 1996 Chevrolet K1500

1 Answer

2004 Pontiac GA brakes going back once a month


Sounds like the master cylinder isn't releasing pressure after you remove your foot... Usually the calipers hang up, but you replaced them so...replace the master cylinder and bleed the brakes 

Mar 27, 2009 | 2004 Pontiac Grand Am

1 Answer

Wheel Bearing problem


If you messed up the Spindle by driving on this, It will not be a cheap fix. You may be looking at anywhere from 400.00 to 1000.00 for repair.

Jan 24, 2009 | 2003 Kia Sedona

Not finding what you are looking for?
Cars & Trucks Logo

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...