Question about 2007 Hyundai Sonata Limited Sedan

1 Answer

Change stoplamp How do I change a deck mounted stoplamp?

Posted by on

  • flee41501 Dec 02, 2008

    Unfortunately, it's not as easy as it sounds. The hole for the lamp position is offset about 4-5 inches. You cannot get to the bulb to remove it without taking loose the lens holder. You have to remove 2 screws to do that, one of which is hidden by a piece of foam tape.
    Also it is impossible to remove the lens holder without slipping a finger underneath to turn the bulb holder. I had to cut off a portion of the bulb holder to slip the lens back in. I left the screws out, as it is impossible to put them back after removal. No wonder the dealer wants $50 to change the bulb-it took me about 45 minutes.


×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 260 Answers

  1. Open the trunk lid and then disconnect the connector of high mounted stop lamp.
  2. Remove the package tray
  3. Replace the bulb (A) from the package tray.
  4. Installation is the reverse of removalchange stoplamp - ef9e985.gif

Posted on Dec 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What else can i do?My brake light are no working and i already change the switch pedal and the fuse its ok what else can be wrong? Lincoln town car 2004


Check the light bulb fittings are not corroded or disconnected.
Otherwise a long wire with clips on to check the circuit is complete from fuse to each side of the lamp fitting, or in between

Nov 18, 2015 | 2001 Lincoln Town Car

1 Answer

Why the stoplamps of my mustang 1996 dont on


Did you check the stop lamp switch on the brake pedal linkage under the dash ? should have battery voltage going into it an coming out when you step on the brake pedal ! Do the high mount stop lamps light ?

Jul 11, 2015 | Cars & Trucks

2 Answers

I have a 05 ford freestar and the third brake light stays on what can I do


elect,issues. very tricky if running battery down overnight.u have a short/ground problem. refer to fuse panel locate fuse@remove till u can have a mech trace it down.

Feb 04, 2015 | 2005 Ford Freestar

1 Answer

How to replace the third brake light bulb on 2005 ford five hundred


9_5_2012_9_14_11_pm.gif

  1. Remove the parcel shelf.
  2. Remove the 4 high mounted stoplamp mounting screws.
  3. Remove the high mounted stoplamp.
  4. To install, reverse the removal procedure.
Parcel Shelf Removal and Installation


9_5_2012_9_15_32_pm.gif

Sep 05, 2012 | Ford Five Hundred Cars & Trucks

1 Answer

Brake lights wont go off


If the stoplamps are on continuously, the following may be at fault:
  1. Circuitry.
  2. Brake pedal position (BPP) switch.
  3. Multifunction switch (Crown Victoria equipped with the police street appearance package or Grand Marquis)
CHECK THE BRAKE PEDAL POSITION (BPP) SWITCH
Disconnect: BPP Switch. Do the stoplamps continue to illuminate? If yes, continue to the next step. If no install a new BPP Switch.

CHECK CIRCUIT 511 (LG) FOR SHORT TO POWER
Disconnect: Central Junction Box (CJB) Fuse 14 (20A). Do the stoplamps continue to illuminate? If yes, and your Crown Victoria is equipped with the police street appearance package or Grand Marquis, continue to the next step. If Crown Victoria, REPAIR circuit 569 (DG). TEST the system for normal operation. If no, REPAIR the circuit. TEST the system for normal operation.

CHECK CIRCUIT 9 (LG/OG) FOR SHORT TO POWER
Disconnect: Multifunction Switch C202c. Does the LH stoplamp continue to illuminate? If yes, REPAIR the circuit. TEST the system for normal operation. If no, go to next step.

CHECK CIRCUIT 5 (OG/LB) FOR SHORT TO POWER
Disconnect: Multifunction Switch C202c. Does the RH stoplamp continue to illuminate? If yes, REPAIR the circuit. TEST the system for normal operation. If the high mounted stoplamp continues to illuminate, REPAIR circuit 569 (DG). TEST the system for normal operation. If the high mounted stoplamp does not continue to illuminate, INSTALL a new multifunction switch. TEST the system for normal operation.

Mar 09, 2011 | 2005 Ford Crown Victoria

2 Answers

Replace rear window brake light bulb


I just had to do this, and it isn't all that easy or quick. First, gently work the gray, carpet like cover loose from the area around the tail light ,(this may give you a little trouble). Once you have done this, you will see three silver nuts. These must be unscrewed. The lower left nut must be accessed through a hole next to where the trunk lid fits. (The screws are permanently attached to the lens housing so will not drop into obscurity when the nuts are removed). After removing the nuts, GENTLY work the lens housing away from the car. You may need a screw driver to unseat the housing, but just be gentle.

You will find three bulbs inside the lens. The brake light bulb is on the lower right side. Simply pull the old bulb out and insert the new one.

Just reverse these directions to reassemble the housing.

May 04, 2009 | 2002 Lincoln LS

1 Answer

1998 Mercury Villager Break light switch


go here for help. http://autos.groups.yahoo.com/group/villagerquest/

Brake light circuit goes through turn signal switch. Do turn signals work ok? Does high mount stop lamp do this too? If you disconnect brake switch, do the lights go off? Do you have trailer tow? Maybe that wire is an issue. I would check brake switch first again. Maybe out of position.

I think you need to adjust the switch.

Installation
  1. Install the BPP switch.
  1. Adjust the BPP switch. Refer to the procedure in this section.
  1. Tighten the BPP switch locknut to 12-15 Nm (9-11 lb-ft).
  1. Connect the BPP switch electrical connector.
  1. Connect the battery ground cable.
Section 17-01: Lighting, Exterior 1998 Villager Workshop Manual
ADJUSTMENTS Brake Pedal Position (BPP) Switch
  1. Measure the distance between the brake pedal stopper and the threaded end of the brake pedal position (BPP) switch. The BPP switch height (A) should be 0.3-1.0mm (0.012-0.039 inch).


ce51ecc.gif

  1. If the BPP switch height is not within specification, loosen the BPP switch locknut.
  1. Adjust the BPP switch until the height is within specifications.
  1. Tighten the BPP switch locknut to 12-15 Nm (9-11 lb-ft).
STOPLAMPS Condition Possible Source Action
  • Stoplamps/Rear Hi-Mount Lamp Inoperative
  • Fuse.
  • Circuit.
  • Brake pedal position (BPP) switch.
  • GO to Pinpoint Test Step K1 .
  • One or More Stoplamps Inoperative
  • Stoplamp bulb(s).
  • Circuit.
  • GO to Pinpoint Test Step L1 .
  • Stoplamps/Rear Hi-Mount Lamp On Continuously
  • BPP switch.
  • REPLACE the BPP switch.


f4078b8.gif

Apr 20, 2009 | 1998 Mercury Villager

2 Answers

Hyundai 2006 Sonata high mount brake light.


the rear seat does NOT have to be removed in order to replace the stoplamp and/or its bulb.
you have to get into the trunk, and there are (2) philips screws holding the stoplamp secured to the package tray. the actual process takes about 15 minutes, because to do it right you have to actually get IN the trunk.

the price they charged you sounds about right if the price of the stoplamp is included, dealerships tend to overcharge for parts.

Apr 11, 2009 | 2006 Hyundai Sonata

1 Answer

Changing the bulbs in the window brake light


Here ya Go!

REMOVAL PROCEDURE
  1. Open the rear compartment lid.
  2. Rotate the high-mounted stoplamp socket(s) counterclockwise to release from the high-mounted stoplamp.
  3. Remove the bulb(s) from the socket(s).
INSTALLATION PROCEDURE
  1. Install the bulb(s) to the high-mounted stoplamp socket(s).
  2. Install the lamp socket(s) to the high-mounted stoplamp, then rotate clockwise to secure.
  3. Close the rear compartment lid.

Feb 11, 2009 | 2001 Chevrolet Lumina

Not finding what you are looking for?
2007 Hyundai Sonata Limited Sedan Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...