Question about 1997 Eagle Vision

1 Answer

Stalling in cold weather

I have a 93 Eagle Vision ESI 3.3 V6. While the car is running, the cruse light on the dash will come on and the car stalls. while the light is on the engine will turn over but not start. When the cruse light goes off the car will start. This only happens in cold weather. I have gone as far as pulling the fuse for the curse control and this has no effect. Rain is not an issue either, just the cold. Most times I can turn the key off, wait a few seconds and the car will start and run fine, lately thats not the case, the cruse light is almost always on now. Any ideas?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The on board computer does not show the error code using the MIL (check engine light ) In my case the fault is in the crankshaft sensor. Had to get the car to a shop to read the OBD1 port to find the error. Replaced the sensor and everything is good. Found out a fault in the cam sensor will cause the same strange issue with the cruise light.

Posted on Dec 02, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1995 Eagle Vision ESI 3.3 liter engine odb1 look like?

you might not have an assembly line communication link [aldl] port if you want to read a code from your check engine light --turn key on [not start]--than off do this 3 times and on 3 rd time light will blink the code [say its 12 it will blink once than short pause than blink 2 more times ] you can retrieve the codes meaning online search obd l codes

Apr 10, 2014 | 1995 Eagle Vision

1 Answer

94 Eagle Vision ESI 3.3 litre could run engine,cut off the ignition switch and the dash lights would come on by themselves seconds later. Replaced the key cylinder and ignition switch to no avail; now I...

You mentioned you replaced the key cylinder, did you also replace the switch located in the column, this is the portion that contains the wiring.

Nov 09, 2013 | Eagle Cars & Trucks

1 Answer

How To Install a Heater Core in a '94 Eagle Vision ESI 3.3

Hello , for heater core or AC evaporator ,, you have to remove the dashboard to reach the housing and replaced them .. no other way

Oct 13, 2017 | 1994 Eagle Vision

1 Answer

Car drives fine untill i go to stop and then the car tries to die i have to put it in neutral to keep it from dieing. it seems like the tranny is still trying push the car. the car is a 1995 eagle vision...

Could be the lockup torque converter is not unlocking. If you leave it in drive but don't hold the brake, does it still die? Does it go forward faster than normal for that condition (3-5 MPH)?

Oct 10, 2010 | 1995 Eagle Vision

1 Answer


Find the EGR valve. Look up on the internet what it looks like and where it is located for your car. There will be a vacuum hose attached to it. start the car when the engine is cold. when it gets to running temperature and starts to stall, pull the vacuum line off. If the EGR is bad, the car will keep running and idle will return to normal.

May 26, 2010 | 1995 Eagle Vision

1 Answer

My 1995 eagle talon esi keeps trying to stall every time i let off the gas, just got oil change new altenator, and plug wires

Sounds like a vacuum problem, This is a fairly common problem right after servicing your car. Sometimes mechanics forget to re-plug your vacuum tube on your engine and you get the stalling unless you give it more gas. Just take it back to your mechanic. It's a real simple solution. He looks under the hood. He sees a loose tube. He plugs it in and off you go.

Mar 16, 2010 | 1995 Eagle Talon

1 Answer

What size motor

vision- esi- motor 3.3lt -201ci- v6 fi ==or vision -tsi- 3.5lt- 215ci- v6 mfi

Mar 03, 2010 | 1994 Eagle Vision

1 Answer

I need the location on a tempature sensor

it is around the thermostat just a little plug type thing with 1 wire on it

Sep 04, 2009 | 1995 Eagle Vision

1 Answer

Where is the oil pressure switch located on a 1997 eagle vision esi with a 3.5 liter engine

Under hood, center, front engine area, mounted on driver side lower front of engine

Jul 04, 2009 | 1997 Eagle Vision

Not finding what you are looking for?
1997 Eagle Vision Logo

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Stewart Dibbs

Level 2 Expert

361 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides