Question about 2000 GMC Jimmy

1 Answer

No key 2000 gmc k 2500 No key how to replace cylinder wih NO KEY !!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

If you just need a key the dealer could make you one with the serial number and proof of ownership. If not you have to drill out the tumblers.

Posted on Dec 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 gmc Jimmy slt 4x4 how can I remove the key cylinder without being able to turn it to the run position because it won't turn at all?


Check to see if something is bound up stopping the key from turning. It is common for the steering wheel to be pushing against its lock and jamming the key. Also make sure the gear selector is all the way in park.

Mar 12, 2016 | GMC Cars & Trucks

1 Answer

My key will not turn in the ignition - how can I start it?


If your key is too worn out, have a new key made. If key is fine, spray some lubricant into key cylinder opening. Use a nozzle to make sure you get lubricant well into key cylinder. Then insert key and wiggle up, down and to sides until cylinder hopefully releases. You may want to leave lubricant penetrate overnight. If this doesnt work, cylinder will need to be replaced. Also, make sure your key is the right key to vehicle. Try it first on a door or hood..

Feb 07, 2016 | 2000 GMC Sierra

1 Answer

Security light flashes key won;t turn


Sounds like the ignition lock cylinder has gone bad. A pretty common problem with GM vehicles. Try tapping it with the handle end of a large screwdriver. Don't be afraid to give it a good whack. Then try the key. If you get it to turn replace the lock cylinder immediately. The key needs to be in the run position in order for the cylinder to be removed. If it can not be put in the run position it makes removal a lot more difficult.

Sep 14, 2014 | 2000 GMC Jimmy

1 Answer

Van won't start,rapid clicking heard when key is turned. need help/directions replacing starter relay for gmc vandura 2500, 1991


Check battery connections and battery fuse. Battery may not be large enough for the size of your van

Jan 18, 2013 | GMC Cars & Trucks

1 Answer

My 2000 gmc 1500 sierra wont start. security message light comes on.


The light is telling you the system does not see the right code in the key. The key could be faulty, or the sensor in the lock cylinder, or the module that controls the PASS system.
If you have another key I would try it first.

Dec 09, 2012 | 2000 GMC Sierra

2 Answers

I have a 2000 GMC Jimmy which needs the ignition lock cylinder replaced. Unfortunately, someone tried to steal it at one point and jammed a screwdriver into the cylinder. The key still goes in the...


You can drill it out. I have had to do this on 2 occassions. First...pull the cowel off around the steering wheel. Get a good light and look closely...some of the screws in the plastic can really hide on you. With cowel removed....look for and opening (small hole) where a little pin sits. Grab a very small screwdriver or pick and push down on that pin while you wiggle the key and try to turn it to the "on" position....you are supposed to put it in the "on" position in order to push the pin in and pull out the cylinder, but you may have some luck seeing as though the tumblers are broke inside. If this doesn't work...you may be drilling it out. Check with dealer too. If you have a plastic top on you key...and a security light and your car....a NAPA or Auto Zone part is not gonna work. You need to buy a key lock and cylinder assembly from the dealer and follow the key up procedure to reprogram the new key to the BCM. when you get a little further into getting it out...I can walk you through getting it in

Nov 14, 2010 | 2000 GMC Jimmy

1 Answer

What size engine does my 2000 yukon xl have is a 4x4


2000 GMC Yukon XL 1500 4WD:
Available engines: 8 Cylinders T 5.3L SFI

2000 GMC Yukon XL 2500 4WD:
Available engines: 8 Cylinders U 6.0L SFI

Hope this help (remember comment and rated this).

Apr 23, 2010 | 2000 GMC Yukon XL

2 Answers

Lock cylinder replacement 00 safari van


Before you replace the cylinder, you might want to try cleaning the cylinder first, its fairly easy and quick.
Use some WD-40 or equivalent and place the spray tube into the tumbler opening were the key would normally go. Make sure you have a rag or something to catch the excess that runs out. Try to flush it out as much as possible.
Then using a can of compressed air, blow the cylinder out, you may need to repeat as necessary. The process should clean debris that is sticking the tumbler.
Give it a try, it should save you some time and money.
Let me know.
Regards,

Apr 06, 2009 | 2000 GMC Safari

1 Answer

2000 GMC 2500 Fuel Pump?


check for power too the pump first with a test light if you have power too it then the pump is bad if not youve got a short some gms also have a fuse check for that also

Feb 23, 2009 | 1985 Chevrolet Chevy

2 Answers

Ignition key


key cylinder pin that holds it in is stuck replace key cylinder they will give you new key along with this

Jun 08, 2008 | 2000 GMC Jimmy

Not finding what you are looking for?
2000 GMC Jimmy Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...