Question about Ford Expedition
YOU MUST PULL ALL THE IGNITION COILS (DIRECT IGNITION) OF THE TOP OF THE SPARK PLUGS, IT IS A 2 HOUR JOB MINIMUM, I HATED THIS JOB AS A FORD DEALER TECH, SHREDS YOUR HANDS.
Posted on Nov 30, 2008
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: changing spark plugs
Changing the spark plugs on a 1997 Ford Expedition 5.4L engine takes patience. Remember to start this project on a cold engine! I started on the passenger side by locating the Coil over iginition coils and cleaned out all the old dirt using some compressed air. Then I had to disconnect the electrical connections to both the Coil over ignition coils and the passenger side fuel injectors. Once you remove the small bolt which holds the ignition coil in place, use your compressed air again to blow out the spark plug hole. After that, you will need a 5/8" swivel spark plug socket and various length extensions to remove the spark plugs. Take your time because there is not much room for your hands. Before installing the new plug, check the gap and use clean engine oil on the new threads. Tighten the new spark plug and reinstall the coil over ignition coil. Reconnect the electrical connection to both the ignition coil and the fuel injector. Continue these steps with all eight spark plugs. You will find the ones on the drivers side are difficult because of the fuel rail gets in your way. Have patience and use swivel extensions to work around the tight spaces. When you are done, you will have saved lots of money! Don't forget to replace your air filter, fuel filter, and pcv valve to complete your tune up.
Posted on Jun 23, 2008
That's because they are hidden quite well. If you look at the engine, you'll see yellow plastic prongs (?) that look like spark plugs, but hook up to the silver tubing. That's the fuel injectors. BUT, right behind the yellow plugs, are black ones. The black one is the connector to the spark plug. The plug itself sits about 4 inches down into the block of the engine. They are a real pain, and from what I can tell, you only have decent access to the first 2-4 of them, then they get too far back and start going under the dash (you'll see what I mean when you get there).
Posted on Aug 06, 2008
These plugs can be difficult, the plug design sucks and if you are not careful you can break them off in the head. Ford issued a TSB069-2008-1 on how to properly remove the plugs and also there is a special tool so if you break a plug off. My friends cost him 300 for a dealer to do it and saved a lot of time. Hope this helps you out.....
Posted on Oct 21, 2009
Several engine sizes there...
1999 Ford Expedition 4.6 liter SOHC V-8 VIN "6"
1999 Ford Expedition 4.6 liter SOHC V-8 VIN "W"
1999 Ford Expedition 5.4 liter SOHC V-8 VIN "L"
Hope this help to solve it (remmeber comment and rated this).
Posted on Apr 20, 2010
I recently changed them and it was a job when you have to crawl up and inside the engine area. But anyways, I started out by buying the E3 plugs, which don't have to be gapped and they do save a little gas plus increased in a little more power. (not much), These set me back $56. go with a basic motorcraft platinum or bosch platinum. I then removed the top engine cover, removed bolts for fuel rail and easily pulled the injector rail up (you will see to replace the o-rings on the injectors by some people, but if you're careful you don't have to.) This gives you the room you need at the back of the engine to remove the plugs. I started at the front by removing the small bolt holding the coil in place, then removing the the coil/wire with a boot removal tool. ( Again you don't need this tool, but it comes in handy at the back plugs). After removing the coil, I simply remove the plug, Apply anti-seize to the new one and install plug. I then apply Di-Electric grease to the inside of the coil boot to prevent moisture getting in. I then install the coil back down on the plug and tighten down and move on to the next.
1. you will need a swivel for the socket
2. you will need an extension, ( I use a long 8" extension)
3. Anti-Seize Grease
4. Di-Electric Grease
5. If installing a plug to be gapped it is .54
6. After installing, check for fuel leaks at the injectors.
It took me about 1 1/2 hours to replace all plugs and a dealer charges about $375. Good Luck if you need any further help get back to me and I'll help any I can.
Posted on Aug 17, 2010
Tips for a great answer:
Aug 23, 2013 | 2002 Ford Expedition
Feb 08, 2011 | 2002 Ford Expedition
Jul 22, 2010 | 2002 Ford Expedition
Jul 22, 2010 | 2002 Ford Expedition
May 17, 2010 | 2003 Ford Expedition
Oct 13, 2009 | 1999 Ford Expedition
Sep 23, 2009 | 2002 Ford Expedition
Jun 03, 2009 | 2002 Ford Expedition
Jan 12, 2009 | 1999 Ford Expedition
Jan 16, 2018 | Ford Cars & Trucks
1,267 people viewed this question
Usually answered in minutes!