Question about 2002 Mazda Protege

1 Answer

2002 mazda poetege> correct timing mark alignment.

Vehicle performance was great before (joe shmuck) replaced the timing belt,now he thinks the belt is set off the mark,??need help asap,need to reset the cam and crank the the correct marks.Thanks

Posted by on

  • 1 more comment 
  • Anonymous Mar 17, 2014

    belt broke ,need marks to set timing

  • Anonymous Mar 23, 2014

    set up timing belt

  • Anonymous Mar 30, 2014

    reseting timing marks
    cause original marks were lost

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

Http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528019f906



there are other diagrams on that page if this is not the right one.

Posted on Dec 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace timing belt on 2002 kia spectre


Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE
    Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-0.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-1.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-3.gif
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

Feb 10, 2016 | 2002 Kia Spectra

1 Answer

How to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve engine


Choose:

1994 Mazda MPV timing belt replacement, 6 cylinder DOHC ...

? 3:46
https://www.youtube.com/watch?v=sD2G-NzycvU
Aug 11, 2011 - Uploaded by rsarp
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0... engine so the valves would not be bent ...

How to replace the timing belt on a 1994 mazda 929 3.0 ...

www.fixya.com/.../t25991928-replace_timing_belt_1994_mazda_929_3...
4 hours ago - how to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve... I have a 2000 Mazda 626 4cyl 2.0 liter DOHC engine replacing the timing belt, what ... 2004 6s, 3l. where is the canister purge valve solenoid located?

Where are the timing marks on a 1994 mazda 929 3.0l - Fixya

www.fixya.com/cars/t25991952-timing_marks_1994_mazda_929_3_0l
4 hours ago - where are the timing marks on a 1994 mazda 929 3.0l - Mazda Cars ...1994 Mazda E2000 Cam Timing Mark Positions to Replace Timing Belt ... on a 1994mazda v6 dohc 24 valve engine How to align the timing mark on the ...

Mazda Timing Belt Replacement



Dec 03, 2015 | Mazda Cars & Trucks

1 Answer

How to aliane marks on cam shaft pulley on mazda protege 2002


1. Remove all spark plugs so that the crank shaft could be rotated easily.
2. Rotate the crankshaft to align the timing mark of the crankshaft gear with the index mark on the engine cover.
3.Rotate the crankshaft +/- 30 degrees to ensure that the valve could not hit the pistons when aligning the camshaft gears.
4. Align the camshafts as described below.
5. Align the crankshaft timing gear with the index mark.
6. Loose and lock the timing bearing at its farther position. Install a timing belt starting from the crankshaft gear, then right cam, then left cam, and at last the timing bearing.
7. Press and hold the timing belt to keep it firm on the gears and loosen the timing bearing. It will get adjusted by itself with the help of spring attached to it. Do not put extra force on the bearing to adjust it more.
8. Confirm the timing marks.
25659142-ts5vql1j3jwqenesgxdwpnsg-5-0.png

Apr 22, 2015 | 2002 Mazda Protege

1 Answer

2000 mazda protege correct timing mark alignment


Presuming the timing belt has not been removed or has skipped.
If the belt is removed or skipped this is an interference engine, valves and or pistons could be damaged by turning crankshaft, seek professional help.
Turn crankshaft clockwise and align timing marks (see jpg).
Face the marks (I) and (E) of the camshaft straight up, then align the timing marks with the horizontal surface on the cylinder head.
Pulley boss position pin on the crankshaft should be facing straight up.
25327211-bog4asmiohngydsbtkv4ivhw-1-0.jpg
This is only the beginning of an involved process, 3 pages in shop manual. I recommend getting a manual, many available on line. one typical Mazda 323 Protege Repair Manual 1990 2003
insure that the manual you get has info on your engine.

Dec 18, 2014 | 2000 Mazda Protege

1 Answer

Setting timing marks


Mr. RAGSDALE.
I do not know if you did strip the belt yet or not. If you did not,I will advise you a just easy and good way to do it yourself. String for the stripping,you just remove the outside belts and pulleys,remove the plastic covers of the timing belt. Just put on the crankshaft the pulley bolt and slowly slowly turn the engine until you see all the marks aligned. On the Camshafts the two sprockets do have the letters "E" and "I", E= Exhaust and I= Inlet.means that the inner to dashboard side is the inlet cam and to the vehicle front the exhaust cam. These two cams with the letters must be aligned,with the crankshaft sprocket
having on the side a small groove which mus be aligned with a small point ball behind the sprocket on the cylinder block. There are your marks. Loose the tensioner and remove the belt.

Good Luck!

Mar 10, 2014 | Mazda MX-3 Cars & Trucks

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

2 Answers

Need for 2002 dodge stratus 2.7 timing chain diagram online


  1. Remove the timing belt.
    06009-sebr-g15.gif

    Crankshaft and camshaft timing marks-2.4L engine
    06009-sebr-g16.gif

    Timing belt tensioner-2.4L engine
    06009-sebr-g17.gif

    Camshaft sprocket alignment-2.4L engine
    06009-sebr-g18.gif

    Timing belt installation-2.4L engine
    06009-sebr-g19.gif

    Timing belt tension adjustment-2.4L engine
    06009-sebr-g20.gif

    Timing belt tension verification-2.4L engine

Dec 01, 2010 | 2002 Dodge Stratus

1 Answer

Set harmonic balancer to top dead centre,set cams to timing marks,engine will not start but turns over. Hyundai Terracan 2002


hi from uk assume you have renewed c/belt and balance shaft timing belt? if so? and sure your timing marks on cams and the c/shaftcog are correct ? the oil pump also correctly aligned with marks? and the balance shaft gear also has time marking ? want to run thro how and which marks you have aligned and at TDC No1 all belt/s have to be aligned ??

Dec 27, 2009 | Hyundai Sonata Cars & Trucks

1 Answer

Timing Belt 2002 Mazda 626


re-install belt, lining up the timing marks, crank to TDC #1 cylinder, cma pulleys have marks on them, line them up to the index marks as well. If you have a drive wheel in the air, you can pop the car into 5th gear (make sure it's chocked!) and rotate the wheel to turn the engine for alignment, etc. You can put a wrench/socket on the cam bolt to align it as well.

Aug 04, 2008 | 1999 Mazda 626

Not finding what you are looking for?
2002 Mazda Protege Logo

531 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...