Question about Toyota Camry

1 Answer

Any way to get rear drivers side window up on 1999 camry. Door panel is off.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

You can find the wires going to the motor and apply 12volt power to them to manually to move the motor.If you reverse the wires it will go in the other direction.If your motor is bad then it gets i little difficult.Write me back if that is the case.

Posted on Nov 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I correct wind noise on drivers side door / window 1999 Camry?


There may be a torn, missing, or loose door gasket. If you inspect the seal and find torn or missing segments, repair or replace. If the seal is intact, the the most likely cause is a gap in the door seal near the top rear of the door. This happens over time because the door frame can actually get bent slightly outward. It is so little as to not be visible, but you can hear the wind noise. The way to get the noise to stop is to open the door and roll the window all the way down. Then, holding the door firmly, grasp the upper rear corner and pull it inward (toward to the car). A couple of sharp tugs will usually do the trick. I know it sounds silly, but it works. BE SURE TO HAVE THE WINDOW DOWN OR YOU COULD SHATTER THE GLASS!
The door frame is quite thin compared to other car body parts and will bow/bend if you pull on it. Start out carefully and if you don't get the results you want, try again with more force.

Nov 21, 2014 | 1999 Toyota Camry

1 Answer

How do you adjust window angle 1999 Camry for better seal


you would need to remove the inner door panel. Loosen the bolts that hold the window regulator in place. Look for any slotted holes with the loosened bolt heads--those are your adjustment holes. Manually tip the window forward, noticing which bolts move and tighten accordingly.

Feb 16, 2014 | 1999 Toyota Camry

1 Answer

Remove and replace drivers door 1999 taurus?


Please don't forget to rate! Thank you!

Removal & Installation
c17hydro_32.gif

The door-to-body mounting



c17hydro_33.gif

Detach the door wiring from the connector


This is a two person operation.

  1. Remove the two door check-to-body retaining screws.

WARNING

Cover the end of the check strap to prevent possible paint damage.


  1. On the rear doors, remove the rear door trim panel, detach the electrical connectors from the components (if equipped) and remove the wiring harness from rear door.
  2. On the driver's side front door, disconnect the window regulator wiring, if so equipped, by removing the wire connector cover, loosening the screw and separating the connector halves.
  3. On the passenger side front door, remove the rubber harness protector from the body to reveal the electrical connectors. Detach the two electrical connectors.
  4. If the door is to be replaced, transfer the following components to the new door if in usable condition:
    • Door trim panel
    • Watershield
    • Outside mouldings
    • Trim clips
    • Window regulator
    • Door latch components.
  5. Remove the hinge retaining screws and nuts from the door and remove the door.

To install:

  1. Position the door onto the hinges and hand tighten the screws.
  2. Align the door and tighten the screws to 19-25 ft. lbs. (25-35 Nm).
  3. If removed, install the wiring harness to the rear doors.
  4. Attach the electrical connectors to the door panel.
  5. Install the door panel(s).
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 31; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Nov 20, 2010 | 1999 Ford Taurus

1 Answer

Install motor/regulator to 2000 camry solara


It easy ! You need a philips2_bing.gif and flat screw driver,8" X 4" block of wood and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch panel ( aka master switch panel) with the flat screw driver and disconnect it. On the side of the door panel just above the striker is this plastic push pull typeof a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder ( driver or front passenger door) in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in two pieces. Use philips and get the only hold down screw you see out.( you may have to pry out al ittle screw cover first) Now the handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the six gold2_bing.gif bolts first(For motor and regulator) Then push the window down till you see the two bolts holding the window to the regulator .Remove them, BEFORE YOU PULL OUT THE MOTOR AND REGULATOR YOU WILL SEE TWO TANGS THAT HELP HOLD THE REGULATOR AND MOTOR TO THE DOOR MARK THE RELOCATION , NOW pull out the motor and regulator have an assistant hold up the glass while you place the two blocks of wood to hold up the window. Now order your regulator and installation is in reverse. Good luck kate. Keep me posted.
Comments:

Apr 21, 2010 | 2000 Toyota Camry Solara

1 Answer

I have 2002 toyota camry xle window switch not working right


You have the wires connected to the wrong switches. Just reverse the wires with the door panel off until the correct switch operates the correct window. Also, the entire switch for each window on the driver's side could have been put in the wrong place on the switch pad even if they are correctly wired.

May 28, 2009 | 2002 Toyota Camry Solara

2 Answers

Divers window won't roll up my Camry


No won't be fuse. My guess is there is something faulty with the main controller. You could probably verify this by trying the switch on right rear passenger door. If it works there then the problem is at the main controller in the driver door. Could be a loose wire or the switch itself is broken.

May 13, 2009 | 1986 Toyota Camry

1 Answer

Camry 1999 power windows and door lock didn't work


did you check the relay under the hood ? look and see if you can find your power box under the hood and under the lid of that box you will find the location of the window relay check that first before tearing into the door panel switches .. thanks Jerry and holler if you need more

Apr 12, 2009 | 1999 Toyota Camry

1 Answer

'88 toyota camry rear window stuck in down position


To get to the Window:

Remove Door Inside Handle:
remove screw, slide the handle forward.
Disconnect the control link and remove the handle.

Remove Door Trim with Inner WeatherStrip:
Remove the two screws from the armrest.
Insert a screwdriver between the trim retainers and the door panel to pry it loose.  Eight hidden fasteners. 1 top left side of door.
1 right side about same height as top of armrest. 1 (each side) about same height as bottom of armrest. 1 on each corner bottom. 1 bottom in middle.  1 on left side between bottom corner and the previous at about lower armrest height...

Remove Service Hole cover.
Remove Door Glass Run.

Remove Division Bar (upper window section divider):
Remove the two screws under the weatherstrip
Remove the bolt.
Pull out the division bar.

Remove the Window Glass:
Place the glass in the door cavity.
Remove the two glass channel mounting bolts.
Remove the window glass by pulling it upwards.

You now have access to the Power Window Regulator; possible replacement of motor etc.

What type of 'things' have you tried for fixing the window and restoring operation?

Jan 22, 2009 | 1988 Toyota Camry

2 Answers

There is a water leak somewhere in my 98 toyota camry that leaks into my passenger side floor. There is no sun roof and no visible leaks from the windows or doors. Any thoughts? A/C leak maybe? water...


I am the original owner of camry xle 1998 with wet floors. In 2000 I had drivers side door seal leaking at welt. Removed old door seal and new weather strip on drivers side installed. The door panel was never wet, but wet at bottom of door where there are drain holes...slowly leaking under carpet.
In 2001 later water again. Coming from overflowing A/C evaporator-drain plugged/ tank full of debris. Removed evaporator, cleaned + drain cleaned.
In 2003, driver door seal against window rotted. Removed door panel and found leak at window belt molding at the mirror joint inside + out. Lots of mold under carpet needed to replace! Made a fuss at dealers for reacurring problem and they replaced the carpet for free.

Sep 07, 2008 | 1999 Toyota Camry

1 Answer

1990 camry power window problem


It is rare that the power window relay will fail. Personally, I would look to see if there is power at the master switch on the driver's door. Anywhere. If the is NO POWER, you have a broken wire between the door & the LF kick panel where the wires come thru the body into the door shell. If there is power, the master switch is narmally the culprit

Jul 25, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...