Question about Mitsubishi Mirage

1 Answer

What do I do when my dim lights aren't working but my brights work just fine

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

I would check the headlight switch that more than likely your problem.thanks jeff

Posted on Nov 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Corolla 2006- both driving headlights dont work,dims work. brights work if lever is pulled back, bulbs have been tested .wiring appears to be fine . all other lights,indicators are fine. car is drive


as positioning the lever in certain positions allows the lights to work then the problem will most likely be in the light switch itself. Replace the light switch unit.

Nov 21, 2014 | 2006 Toyota Corolla 1.6

1 Answer

Dims dont work and brights are not bright


check the bulb sockets , ck your ground

Mar 12, 2013 | Cars & Trucks

1 Answer

Gmc envoy bright lights work dim lights will not work


Your circuit lights may be bright or dim according to how your electrical system was set up. It may dim when lights are off and get bright when lights are on. ------------------------------------------------------------------------------------------
Car Diagnostic Tools

Nov 24, 2012 | Buick LaCrosse Cars & Trucks

1 Answer

Only one bright light works even after replacing the bulb. What could be the reasons for this? All other lights work fine.


it sounds like you have an open curcuit in the b+ wire. the can be at the back of the conector/pigtail.

May 22, 2012 | 1994 Nissan Maxima

1 Answer

Bright lights turn on when making right turns


The solution is to replace (or possibly repair) the turn signal/dimmer switch.
The switch has three contacts and a slide which control the bright lights and is filled with dielectric grease. When the temperature goes down the grease gets a little thicker and the slide won't work very well.
The switch has two screws and one plug and can be accessed after removing the top steering column cover.

Jan 24, 2012 | 2007 Ford Escape

1 Answer

Alero: low beams as bright as Daytime runners while brights work?


Look for the relay for the head lights,it may be bad.Also look for a bad ground.And check the bulbs too.

Nov 04, 2009 | 2003 Oldsmobile Alero

1 Answer

2004 Cavalier Day/dim lights not working


I finally got mine fixed!! It was the crossover wires between headlights(the wires that run in front of the radiator). One wire was torn into. Spliced them and taped back together. Hope this works for you!! I also used something called wire caps that help hold the spliced wires together. I found this solution on yahoo.com search engine where someone else had suggested this. My only problem was no dim lights, but all the other lights worked fine.

Apr 06, 2009 | 2004 Chevrolet Cavalier

1 Answer

Tail light problem


look at all wiring, weather can make the skin of a wire become brittle, 2 or more wires can be touching one another

Feb 23, 2009 | 1986 Dodge Aries 4 Door

1 Answer

Lights go out


Dimmer switch is going bad. If you rapid fire the switch they will switch from bright to dim or dim to bright. replace the colum switch.

Feb 08, 2009 | 2001 Dodge Ram 3500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...