Question about 1990 Mitsubishi Montero

1 Answer

Cam and crank out of sync

Took timing pulley off to replace oil ring on dis. houseing

Posted by on

  • gloria857 Nov 30, 2008

    Do i need to have all engine parts on motor to check camsaft and crank are in sync. Firing order on roter cap looks complex.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 217 Answers

Please clear your problem with more details so as to help u.

Posted on Nov 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While replacing timing belt on my 2003 pt cruiser (2.4 liter) I got the belt on with the crank pulley and compression pulley (top front) in timing but exhaust pulley (top rear) off by one tooth. Took belt...


To readjust the cam timing loosen of the valve rockers so that the valves will not move as the cams are turned.. Set the crankshaft on TDC no 1 piston. This will make the mark on the crank sprocket line up with a mark on the housing. The cam shaft marks are to ne facing each other with the "up" marks facing up. Loosen of the adjuster idler and use an allen key to lever the pulley away from the belt. Fit belt and let tensioner off Ensure tensioner spring is in line with the notch. Repeat procedure to get it there.. The valves will now be timed . replace the rockers and adjust as required . The problem that you had is that there was load on the cam lobes from incorrect positioning of the cam shafts and the shaft turns until the load was equal between two lobes.. There is every possibility that there will be bent valves as it is an interference motor.

May 19, 2014 | Cars & Trucks

Tip

2004 Pilot timing belt replacement



(for the 105,000 mile timing belt service)

Part List :
-Timing belt: 14400-P8A-A02
-Adjuster automatic (hydraulic tensioner): 14520-P8E-A01
-Adjuster - timing belt: 14510-PGE-A01
-Idler pulley - timing belt: 14550-P8A-A01 (OR) 14550-PGE-A01 (there are 2 numbers listed)
-Alternator/Compressor belt: 38920-P8F-A02
-Power steering belt: 56992-P8A-A01
-O-RING (8.8X1.9): 91302-GE0-000
-Fender trip clips (X7): 91501-S04-003

Special Tools Needed:
Honda Crankshaft Pulley Removal Tool
3/4" breaker bar

Procedure:
-Remove tire and place the Pilot on a jack stand.

-Remove the clips holding the fender liner and lower splash shield in place (x7) and fold them out of the way.

-Make sure the #1 piston is on top dead center using the marks on the crank pulley and lower timing belt cover (19mm in the crank pulley).

-Remove the Alternator-Compressor belt (14mm boxend) & Power Steering belt. (2-12mm and 1-12mm tensioner bolt)

-Loosen the crank pulley. If you have an impact wrench or a long breaker bar it makes it easier to remove the bolt. You will also need a special tool crankshaft pulley holder (50mm) (19mm and special tool).

-Remove the side engine mount bracket (5-14mm bolts).

-Remove the crankshaft pulley.

-Remove the oil dipstick & tube (10mm).

-Remove the front & rear 'upper covers' of the timing belt housing, moving the wire harness out of the way first (5-10mm bolts for each cover).

-Remove the lower cover (7-10mm bolts).

-Remove the engine mount bracket that is bolted to the block (3-14mm bolts).

-Remove the hydraulic tensioner (2-10mm bolts).

-Remove the tensioner pulley (you will reuse the inner sleave) (14mm bolt).

-Remove the idler pulley bolt (14mm bolt with thread locker on it) (I used Loctite 242 during the reinstall because I had it on the shelf).

-Remove the timing belt.

-Before installing a new timing belt, make sure the pulleys, belt guide plate, upper & lower covers are clean and check to see if the crank and cams have rotated (mine did not move).

-The install is the reverse order of removal (make sure you torque everything correctly!)

-The removal of the lock pin in the hydraulic tensioner gave me a little trouble so I used pliers.

-Once the crank pulley is back on, check the lower timing mark (and the cam marks) before the top covers are installed.

on Oct 13, 2014 | 2004 Honda Pilot

1 Answer

Timing marks


You need locking pins for both cam shaft pulleys as well as for the crank. The cam pulleys each have a hole in them which line up with a hole in the cylinder head through which an 8mm bolt cam be used to lock them. If you are looking at the cam pulleys from the RH fender side, the LH pulley hole locks at about 5 o'clock and the RH pulley at about 7 o'clock.

The crank locking pin is in an awkward position and a bit difficult to access. the hole is behind the oil filter housing and the pin locks into a hole in the back of the flywheel.

Please note that if your cam belt has snapped this engine will bend valves. If it is a scheduled belt change then it is quite easy to line up the marks and do the belt replacement.

Apr 27, 2014 | 2005 Citroen C3 1.6i

1 Answer

How do I get the timing right on a Acura legend.


You have to adjust the cam or cams depending on rather or not its a dual over head or single cam motor, with the marks on the crank shaft and oil pump pulley. You can get the timing mark diagrams from a chiltons book or off of Mitchell online. The only problem with mitchell is you have to subscribe to it. The timing cover must come off, the crank pulley also has to come off. When you get to where you can see the timing belt and gears you put the bolt for the crank pulley back in the crack shaft and turn the motor over manually with a ratchet and socket about 5 times until the marks on the cam or cams line up with the mark on the crank shaft and oil pump. If your car is not vtec then the oil pump pulley will not have a mark on it. This is something that probably needs to be done by a shop with technicians who have done it before. It can be a little confusing trying to do it yourself if you have never tried before. I hope this helps. What makes you think the car is out of time?

Apr 08, 2011 | Acura Legend Cars & Trucks

2 Answers

Where are the cam & crank position sensors for a 1999 chevy suburbon 5.7?


THE crank sensor is located at bottom of timing cover on front of engine if you look under engine below crank pulley around oil pan timing cover you will see it. the cam sensor is in the distributor.

Dec 22, 2010 | 1999 Chevrolet K1500

1 Answer

1988-1993 ford festiva leaking oil around the crank pulley... could the oil be coming out of timing chain seal... are could it be a the seal on the crank shaft.. if so would i need to removle the engine to...


This sounds like the crank seal, the engine doesnt have to be removed, in order to get to seal is like replacing the ttiming belt, and once in the timing belt i would replace the crank and cam seals, also do the timing belt, and maybe the waterpump, you will need to remove the crank pulley and then the timing covers then align timing marks for timing belt before ou remove it, with timing belt off the crank pulley then slides off the crankshaft and the seal is behind it, the cam shaft gear unbolts and the seal is behind the gear, once the gears are off then you will be able to remove the seals from the engine,heres a few diagrams to help. good luck and i hope this is helpful,60d826b.gifca916fa.gifcb2cb5a.gif

Oct 31, 2010 | 1993 Ford Festiva

1 Answer

How to you install a water pumpon a 3.5 97 dodge


Remove the hood bracket bar, 4bolts, then the fan shroud assembly, then the belts, belt adjuster, and timing covers, line up the cam gears, crank gear to the marks , cam has 1 dot, they line up to timing housing 2 dots, (single dot to middle of the 2 dots), crank has 1 dot to mark on the oil pump housing to your right of crank gear, thats TDC. now remove the timing belt tensioner, 2 bolts, and remove the belt, if the pump has leaked, replace the belt, and tensioner if it is NOT metal Pulley, the fibre one will break down from the antifreeze. its a good idea to replace the water pump housing orings behind it, ac bracket has to come off, as the right cam on engine, this not a retiming iussue with the gear. GOOD LUCK. RDJRP

Aug 17, 2009 | 1997 Dodge Intrepid

1 Answer

Timing gear set


That is a dual overhead cam engine. On the oil pump housing there is an arrow cast into the housing. Line the arrow on the crank pulley up with the arrow on the oil pump housing, that will set your crankshaft in time. Next you'll need to set your camshafts. This is the procedure for doing that......the exhaust cam gear (nearest the firewall) has markings on it that say "2.4L" on one side and "up^" on the other side. On the left side of the gear is a notch on the tooth. This notch MUST be set at 3:30 and the intake cam at EXACTLY 9:00. Once you've installed the timing belt and you rotate the tensioner to "tighten", the offsetting of the exhaust cam will match up with the intake cam. And presto!!! your timing is now set. Make sure you turn the crank sprocket TWO complete revolutions and verify your timing marks.

Chris

Nov 08, 2008 | 2000 Dodge Caravan

1 Answer

86733GH3 REPAR TIMING BELT


3.0l Mitsubishi 6 cylinder.
support engine... remove engine mount... remove alternator, power stearing pump, compressor (if equipt) do not remove hoses from power stearing pump or compressor move them out of the way were they wont get damaged. Remove the tension pulley for the serpentine belt, and the tensioner for the compressor belt if equipt. then remove the compressor mounting bracket. Next remove the engine mounting plate and the crank pulley and balancer assembly. you should now be able to remove the the 3 piece timing cover. Once removed remove the tensioner spring from the water pump and loosen the tensioner nut. Remove the belt. At this point it is also recommended to replace the water pump and plumbing as well. The water pump service life is aproximately the same as the timing belt at 60,000 miles. This engine in stock form is a non interfering type engine. Meaning that moving the cams or crank out of sync will not cause damage. Turn each of the cams over by hand and line them up with the timing mark on the top of the back cover with the marks on the pulleys. Using a wrench turn the crank so that the pulley mark lines up with the mark cast into the block. replace the belt, tensioner spring (replace tensioner if warn) and tighten the tensioner bolt. roll the crank over 2 complete turns forward and recheck the cams to make sure the marks are still lined up. roll the crank backwards and recheck the timing marks again. (this process is much easier done with the plugs removed.) If everything is still lined up correctly (crank at TDC and cam pulleys pointing to each designated mark on the covers.) reassemble the cover and assessorys in the reverse order that they were removed and reinstall the old motor mount or replace if needed.

Aug 02, 2008 | Plymouth Acclaim Cars & Trucks

Not finding what you are looking for?
1990 Mitsubishi Montero Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...