Question about 2002 Hyundai Accent

1 Answer

2002 Hyunsai Accent rear brakes, do you have to remove wheel hub

Is it necessary to remove the wheel hub in order to replace the brake shoes? It doesn't seem possible to disassemble the shoe springs otherwise.

Posted by on

  • Anonymous Mar 24, 2014

    Does it have brake pads in the rear or shoes

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

Yes, it should be removed it makes the job a lot less difficuilt. 

Posted on Nov 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear brakes


Removal
1.Remove rear wheel and tire assembly from vehicle.

2.Remove rear brake drums from hub and bearing assemblies after loosening the two brake drum screws.
bj6c017a.gif
3.Be sure that the parking brake pedal is in the release(most upward) position.

4.Completely loosen square nut of the rear parking brake cable. Then create slack in the rear parking brake cables.
bj6c017b.gif
5.Remove adjuster spring from adjust lever and brake shoe.
bj6c017c.gif
6.Remove adjust lever and turn the adjusting wheel of adjuster assembly to the direction of the arrow as shown.
bj6c017d.gif
7.Remove the strut spring and the lower retracting spring from the brake shoe.
bj6c017e.gif
8.Remove the upper return spring from the brake shoe.
bj6c017f.gif
9.Remove brake back plate hold down spring and pin from the leading brake shoe assembly.

10.Remove the leading brake shoe. Then remove the adjuster assembly, strut and anchor spring from the trailing brake shoe.
bj6c017g.gif
11.Remove the trailing brake shoe from the brake back plate after removing hold down spring and pin.
bj6c017h.gif
12.Remove the trailing brake shoe from the rear parking cable.
bj6c017i.gif
13.Remove parking pivot lever from the leading brake shoe.
bj6c017j.gif
Replacement
1.Lubricate the eight shoe contact areas on the back plate and anchor.
bj6c017n.gif
2.Install the trailing brake shoe to the rear parking cable.

3.Install trailing brake shoe on brake back plate and install the trailing brake shoe hold down spring and pin on the brake shoe.

4.Tighten the square nut of rear parking cable.

5.Install the anchor spring then install adjuster assembly, and strut.

6.Install leading brake shoe on brake back plate.
bj6c017o.gif
7.Install the brake shoe upper return spring, strut spring and the lower retracting spring to the brake shoe.

8.Properly rotate the adjusting wheel of adjuster assembly to the direction of the arrow in as shown.
bj6c017d.gif
9.Install the adjuster spring on the adjust lever and leading brake shoe assembly.

10.Install the leading brake shoe hold down spring and pin on the brake shoe.
bj6c017q.gif
11.Adjust brake shoes assemblies so as not to interfere with brake drum installation.

12.Install the rear brake drums on the hubs.

13.Check and adjust whether the pedal stroke in the specification.(Refer to section BR Gr./On-vehicle service/Pedal stroke of parking brake)

14.Install wheel and tire.

15.Push the parking brake pedal to the floor once and release pedal. This will automatically remove the slack from and correctly adjust the parking brake cables.

16.Test the vehiche on the road. The adjust will continue the brake adjustment during the road test of vehicle.

Inspection
1.Inspect the disassembled parts for wear, rust or damage.

2.Measure the thickness of brake shoe lining.
Standard : 0.17 in (4.5 mm)
Minimum : 0.04 in (1 mm)

3.If the shoe lining is less than minimum or shows signs of uneven wear, replace new one.
bj6c017k.gif
4.Measure the inside diameter of the brake drum.
Standard : 10 in (254 mm)
Maximum : 10.07 in (256 mm)
bj6c017l.gif
5.If the inside diameter of the brake drum is more than maximum or shows signs of uneven wear, replace new one.

6.Inspect the lining and drum for proper contact. If the contact condition is improper, repair it with a grinder or replace the brake shoe assembly.
bj6c017m.gif

Aug 14, 2013 | 2002 Kia Sedona

1 Answer

How do I get the rear spindle off so I can replace the emergency brake shoes on my 2006 chrysler pacifica?



Adjustment

  1. Place parking brake lever in -full released- position.
  2. Raise and support vehicle.
  3. Remove plug in parking brake shoe support to access adjuster star-wheel.
  4. Through the access hole, rotate the adjuster star wheel in the following direction to expand the shoes outward against the drum:
    1. Left brake - Rotate star-wheel toward rear of vehicle.
    2. Right brake - Rotate star-wheel toward front of vehicle.
  5. Using an appropriate tool, turn adjuster star wheel until wheel will not rotate (dead lock).
  6. Back off adjuster six detents (teeth).
  7. Rotate wheel, checking for light drag. If drag is too heavy, continue to back off adjuster one detent at a time until light drag is present. Do not back off star-wheel more than 17 detents from wheel lock.
  8. Install access plug.
  9. Adjust opposite wheel parking brake shoes using same method.
  10. Lower vehicle.
  11. Apply and release parking brake lever once to ensure proper operation of parking brakes.


Removal & Installation NOTE The following procedure may be used to remove shoes on either side of the vehicle.

  1. Lock out automatic adjuster in parking brake lever.
  2. Raise and support vehicle.
  3. Access and remove rear hub and bearing.
  4. Remove parking brake cable bolt at knuckle.
  5. Completely back off parking brake shoe adjustment.
  6. Remove parking brake shoe adjuster spring.
  7. Remove shoe adjuster.
  8. Remove upper brake shoe hold-down clip and pin.
  9. Remove lower brake shoe hold-down clip and pin.
  10. Remove upper and lower shoes with return spring from shoe actuator.
  11. Remove return spring from shoes.

    0996b43f80204c12.jpg

    Fig. View of the actuator (1), support (2), adjuster spring (3), return spring (4), caliper adapter (5), shoes (6), hold-down clips and pins (7) and adjuster (8)

To install:
  1. Install return spring between upper and lower shoes.
    NOTE Before installing shoes on actuator, make sure actuator hooked to rear cable is positioned with word -UP- facing outward.
  2. Install upper and lower shoes with return spring on shoe actuator located on parking brake cable.
  3. Install lower brake shoe hold-down pin through rear of support and lower shoe, then install hold-down clip.
  4. Install upper brake shoe hold-down pin through rear of support and upper shoe, then install hold-down clip.
  5. Install shoe adjuster. Place end of adjuster with star wheel upward.
  6. Install parking brake shoe adjuster spring.
  7. Install bolt securing parking brake cable to knuckle and tighten bolt to 21 ft. lbs. (28 Nm).
  8. Using Brake Shoe Gauge, Special Tool C-3919, or equivalent, measure inside diameter of parking brake drum portion of rotor.
  9. Place Gauge over parking brake shoes at widest point.
  10. Using adjuster star wheel, adjust parking brake shoes until linings on both park brake shoes just touch jaws on gauge. This will give a good preliminary adjustment of parking brake shoes, before a final adjustment is made at end of this procedure.
  11. Install hub and bearing with wheel speed sensor as well as all components necessary to access it.
  12. Lower vehicle.
  13. Unlock automatic adjuster in parking brake lever.
  14. Perform final adjustment of parking brake shoes

  15. Adjustment This vehicle is equipped with permanently sealed rear wheel bearings. There is no periodic lubrication or maintenance recommended for these units.


    Removal & Installation

    1. Raise and support vehicle.
    2. Remove wheel mounting nuts, then tire and wheel assembly.
    3. If equipped with AWD:
      1. Remove cotter pin, nut lock and spring washer from half shaft.
      2. While a helper applies brakes to keep hub from turning, remove hub nut and washer.
    4. Remove brake caliper and rotor from hub and bearing assembly.

      0996b43f807cb548.jpg

      Fig. Hub assembly

    5. Disconnect vehicle wiring harness connector at wheel speed sensor connector.
    6. Unclip wheel speed sensor connector from spare tire mounting support.
    7. Disconnect two sensor cable routing clips on rear suspension crossmember.
    8. Disconnect two sensor cable routing clips along toe link.
    9. Disconnect sensor cable from bracket on brake support.

      0996b43f807cb54d.jpg
    10. Completely loosen, but do not remove four bolts fastening hub and bearing in place. Once loosened from threads in hub and bearing, push bolts up against rear of hub and bearing to keep brake support plate in place when hub and bearing is removed.

      0996b43f807cb54e.jpg

      Fig. Rear hub and bearing mounting bolts

    11. Pull hub and bearing off knuckle and half shaft (if equipped with AWD), then thread wheel speed sensor cable through hole in brake support plate as it is removed with hub and bearing.
      0996b43f807cb54f.jpg
    To install:
    1. Position hub and bearing bolts though rear of knuckle and parking brake support just enough to hold support in place as hub and bearing is installed.
    2. Install hub and bearing by first feeding end of wheel speed sensor cable through hole in bottom of parking brake support. As this is being done, if equipped with AWD, slide hub and bearing onto half shaft. Place hub and bearing through brake support, onto knuckle, lining up mounting bolt holes with bolts and placing wheel speed sensor head at bottom.
    3. Install four bolts fastening hub and bearing in place. Tighten mounting bolts to 60 ft. lbs. (81 Nm).
    4. Place wheel speed sensor cable routing grommet into bracket on parking brake support.
    5. Route wheel speed sensor cable along toe link and rear suspension crossmember connecting routing clips where shown.
    1. Connect vehicle wiring harness to wheel speed sensor connector.
    2. Install brake rotor and caliper.
    3. If equipped with AWD:
      1. Install washer and hub nut on end of half shaft.
      2. While a helper applies brakes to keep hub from turning, tighten hub nut to 180 ft. lbs. (244 Nm).
      3. Install spring washer, nut lock and cotter pin on end of half shaft.
    4. Install tire and wheel assembly. Install and tighten wheel mounting nuts to 100 ft. lbs. (135 Nm).




May 18, 2011 | 2006 Chrysler Pacifica

1 Answer

Remove rear brake drums


Light Duty Models
  1. Raise the vehicle so that the wheel to be worked on is clear of the floor and install jackstands under the vehicle.
  2. Remove the wheel. Remove the three retaining nuts and remove the brake drum. It may be necessary to back off the brake shoe adjustment in order to remove the brake drum. This is because the drum might be grooved or worn from being in service for an extended period of time.
  3. Before installing a new brake drum, be sure to remove any protective coating with brake cleaner or a suitable fast-drying degreaser.
  4. Install the brake drum in the reverse order of removal and adjust the brakes.

Heavy Duty
  1. Raise the vehicle and install jackstands.
  2. Remove the wheel. Loosen the rear brake shoe adjustment.
  3. Remove the rear axle retaining bolts and lockwashers, axle shaft, and gasket.
  4. Remove the wheel bearing locknut, lockwasher, and adjusting nut.
  5. Remove the hub and drum assembly from the axle.
  6. Remove the brake drum-to-hub retaining screws, bolts or bolts and nut. Remove the brake drum from the hub.

To install:

  1. Place the drum on the hub and attach it to the hub with the attaching nuts and bolts.
  2. Place the hub and drum assembly on the axle and start the adjusting nut.
  3. Adjust the wheel bearing nut and install the wheel bearing lockwasher and locknut.
  4. Install the axle shaft with a new gasket and install the axle retaining bolts and lockwashers.
  5. Install the wheel and adjust the brake shoes. Remove the jackstands and lower the vehicle.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 32; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 32; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 08, 2011 | 1991 Ford F250

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

2 Answers

How to replace the rear break drums on a hyumdai accent gs


Brake Drums-They seem to be fastened with a nut and have bearings that need to be regreased based on the diagram found for replacing the shoes. Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Wheel 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
To Install:
  1. Install or connect the following: 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
    • Wheel
--- Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Wheel 02-04_hyundai_accent_brake_drum.gif

    • Brake drum 02-04_hyundai_accent_rear_brake_backing_plate.gif

    • Shoe hold-down spring
    • Automatic adjuster spring
    • Adjuster lever
    • Shoe adjuster by spreading the shoes
    • Shoe to shoe spring
To Install:
Note: Apply the specified grease to the shoe to backing plate and shoe to anchor plate contact surfaces.
  1. Install or connect the following: 02-04_hyundai_accent_rear_brake_backing_plate.gif

    • Shoe hold down pin
    • Return spring to the push rod while it is shortened
    • Shoe hold down spring
    • Shoe to shoe spring
    • Shoe adjuster by spreading the shoes
    • Adjuster lever
    • Automatic adjuster spring 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
    • Wheel
Note: After assembling the drum components, pull the parking brake lever all the way up several times
prev.gif next.gifprev.gif next.gif

Sep 30, 2010 | 2001 Hyundai Accent

1 Answer

How do i remove the rear brake drums on a 1999 accent


Take off any hub caps and loosen the lug nuts (just loosen them) with the tire still on the ground it is way easier this way. Jack up the rear and set the car on stands as secure as you can, please be safe. Place chocks under the front wheels to keep it from moving off the stands. Finish removing the lug nuts and remove the rear wheels. Look on the outer edge of your brake drum for a punch slot, it is an oval looking indention in the drum that you punch out to access the rear brake adjusters. If you do not see this punch slot look on the rear back plate for a rubber cap that you can pry out with a screw driver. Inside will be the brake shoes adjusters, you have to back off the adjusters to get the drum off the axel. Once you have backed off the adjusters, you can use a hammer and hitting the drum on the front edge it should come loose now to access the brake shoes. Next work on one side at the time using the other side as your guide remove & replace the shoes . Put it back together.

Jun 06, 2010 | Hyundai Motor 2004 Accent

1 Answer

How to remove rear brake shoes


How to Replace Brake Shoes
(DIY Complexity: Moderate / DIY Time: 3.2 hours)

Parts:
1. Brake Shoe Set

Tools:
1. Combination Wrench Set
2. Floor Jack
3. Jack Stand Set
4. Mallet Hammer
5. Brake Spring Tool
6. Flat Head Screwdriver
7. Needle Nose Pliers
8. Tire Iron
9. Brake Resetting Gauge

Supplies:
1. Brake Cleaner

Steps:
Step 1 * Secure your vehicle on a level surface, making sure your car will not roll or lean when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 * Break the lug nuts loose but do not remove. Lift up your vehicle using a floor jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 3 * Secure the vehicle with jack stands on both sides for safety before starting any work. Do not rely on the jack to hold the vehicle up while working.

Step 4 * Remove the lug nuts. Remove the wheels.
o Tip: Make sure the parking brake is released before removing the brake drum.

Step 5 * Remove the brake drum. If necessary, back off the star wheel adjuster.
o Tip: Hit the brake drum with a rubber mallet to break it loose from a rusted hub.

Step 6 * Clean the brake assembly using a“wet wipe method”. This method uses a spray bottle with water and detergent. Do not use compressed air to clean the brakes. Inspect the brake shoes for wear or damage.
o Tip: It is a good idea to leave one side assembled to use as a reference while you work on the other side.

Step 7 * Remove the primary and secondary brake shoe return springs from the anchor pin and brake shoes.
o Tip: The primary spring is connected to the front (primary) brake shoe and the secondary spring is connected to the rear (secondary) brake shoe.

Step 8 * Remove the adjuster cable and spring assembly. Remove the star adjusting screw and thread the adjuster all the way in.

Step 9 * Remove the front brake shoe retainer. Remove the front brake shoe and parking brake link.

Step 10 * Remove the parking brake lever from the rear brake shoe. Remove the rear brake shoe retainer and remove the rear brake shoe.
o Tip: Specialty brake tools are available to make brake shoe removal easier; but it is possible to remove the brake components with pliers.
o Tip: While you have the drum brake assembly apart, pry the outer seal away from the wheel cylinder and check for leaking brake fluid. If any brake fluid is leaking, replace or rebuild the wheel cylinder

Step 11 * Apply white lithium grease to the backing plate contact points.

Step 12 * Install the new brake shoes in the reverse order of removal. Be careful to keep the new brake shoes clean.

Step 13 * Inspect the brake drum and resurface or replace if necessary. Install the brake drum and adjust the brake shoes.
o Tip: There is a slot on the back of the backing plate usually blocked with a rubber grommet. To adjust the brakes, insert a screw driver into the slot and turn the star wheel adjuster. Spin the brake drum and stop adjusting when you feel a slight drag.

Step 14 * Install the wheels. Torque lug nuts to manufacturer’s specifications.

Step 15 * Lower vehicle and test drive to verify repairs.

Hope help with this (remember rated and comment this help).

Mar 11, 2010 | 1988 Toyota Pickup

1 Answer

Rear brake on 2002 hyundia accent


hi from uk after supporting car on stand or blocks ? remove wheel then you will see x head screwsx2 remove screws then release handbrake drum should now rotate freely you may need to lightly but firmly tap the drum off the hub if you have an old vac ? use it to vac the dust from shoes and drum ? if your shoes are ok ? then make sure the auto adjuster is free and clean? if your h/brake travel is high and the reason for checking brakes? then notch up auto adjuster a couple of clicks at atime whilst keep trying the drum fits so the shoes are just enabling rotation of drum by hand then press b/pedal a cople of times to centralise shoes to drum ? if drum still rotates freely with no binding on shoes ? then re assemble carry out same proceedure on other side ? do not adjust brake cable! unless you do adjustment as above you may/will find your h/brake is better /less travel ? also your foot brake will feel better and less travel ? hope this helps you but if you req further info/assistance by all means come back to board best wishes from lancashire uk

Jun 04, 2009 | 2002 Hyundai Accent

1 Answer

94 landcruiser brakes


Rear DRUM instructions are first If you would Like Pictures and all They Must Be Emailed as TOO LARGE For FixYa's Format im at aol.com
Just use my Knickname@ and let me know where to send.


  1. Raise and support rear of vehicle, then remove wheel and tire assembly.
  2. Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
  3. Remove tension spring, using a suitable tool, then remove rear shoe hold-down spring and pin. Remove rear brake shoe and anchor spring, Fig. 7.
    1. On Land Cruiser models, remove front hold-down spring using a suitable tool, then disconnect the parking brake cable from the parking brake bellcrank, Fig. 7.
    2. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, remove front shoe hold-down spring and pin, using a suitable tool, then disconnect No. 1 parking brake cable from No. 3 parking brake bellcrank.
    3. On 2WD T100 models, proceed as follows:
      1. Remove E-ring, then automatic adjusting lever and C-washer, then parking brake lever. Disconnect brake line from wheel cylinder using a suitable container to catch fluid.
      2. Remove wheel cylinder. Remove following parts from wheel cylinder: two boots, two pistons, two pistons cups and spring.
    1. On models except 2WD T100, remove front brake with strut, then disconnect parking brake cable from front shoe. Remove parking brake cable No. 2.
    2. Remove adjusting lever spring, then the adjuster from front shoe.
    Inspection
    1. Measure brake drum inside diameter. Inside diameter should be 11.61 inches,
      1. Measure brake shoe lining thickness, Fig. 3. Minimum thickness should be .04 inch on models except on T100 models and .039 inch on T100 models.
      2. Inspect brake lining and drum for proper contact and replace drum or shoes as necessary.
      3. Inspect wheel cylinder for corrosion or damage.
      4. Inspect backing plate for wear or damage.
      5. Inspect bellcrank components for bending, wear or damage.
      6. Apply a suitable lubricant to backing plate contact areas.
      Installation
      1. On 2WD T100 models, proceed as follows:
        1. Apply lithium soap base glycol grease to piston cups, pistons and boots.
        2. Assemble and install wheel cylinder.
        3. Connect brake line to cylinder.
      1. Apply high temperature grease to following parts:
      1. Apply a suitable lubricant to adjuster bolt threads and end.
      2. Assemble adjuster to lever, then install adjuster lever spring.
      3. On Land Cruiser models, install parking brake lever cable to parking brake shoe, then attach cable to bellcrank.
      4. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, install No. 1 parking brake cable to parking brake lever shoe, then attach the other side of cable to No. 3 bellcrank.
      5. Position front shoe in place with end of shoe inserted into piston, then install shoe hold-down spring and pin using a suitable tool.
      6. Assemble anchor spring to front and rear shoe, then install rear shoe with end inserted in piston.
      7. Install rear shoe hold-down spring and pin, then the tension spring.
      8. If necessary, adjust bellcrank as follows:
        1. Lightly pull bellcrank in direction "A", Fig. 8, until there is no slack in part "B".
            1. Rotate adjusting bolt until dimension "C" is .016-.031 inch.
            2. Lock adjusting bolt with locknut, when connect parking brake cable to bellcrank.
            3. Install tension spring.
          1. Ensure proper parking brake travel.
          2. Pull adjusting lever cable upward, then release and ensure adjusting bolt rotates. If bolt does not rotate, check for improper installation of rear brakes.
          3. Adjust strut to shortest possible length, then install drum.
          4. Pull parking brake lever fully upward. Repeat process several times.
            1. Remove drum, then check for proper clearance, Fig. 4. Clearance should be .024 inch. If clearance is not as specified, check parking brake system.
            2. Install brake drum, then bleed and refill brake system.
            3. Install wheel and tire assembly, then lower vehicle.

FRONT ROTORS & PADS
  1. Remove caliper.
  2. Remove cap and snap ring, Fig. 10, then remove cone washers with tapered punch.
  3. Insert suitable length bolts into flange bolt holes, then tighten bolts evenly and remove flanges.
  4. Remove free wheel hub cover and snap ring, then remove nut, spring washer and cone washer with suitable tapered punch.
  5. Remove free wheel hub body and gasket.
  6. Remove locknut, lock washer and adjusting nut.
  7. Remove axle hub and brake disc as an assembly.
  8. Remove oil seal and inner bearing from hub.
  9. Reverse procedure to install. Torque adjusting nut to 43 ft. lbs., then back off nut. Torque nut to 18 ft. lbs. Using spring scale attached to hub bolt, check that preload is 1.4-12.6. Install lockwasher and locknut, if equipped. Torque locknut to 35 ft. lbs., and recheck preload. Secure lockwasher by bending one tab inward and one tab outward.
  1. Raise and support front of vehicle, then remove tire and wheel assembly.
  2. Remove clip and hole pins, Fig. 9.
  3. Remove anti-rattle spring and shim(s) if equipped, then remove brake pads.
  4. Lubricate caliper housing with suitable brake grease at pad contact points.
  5. Reverse procedure to install.

Jan 28, 2009 | 1994 Toyota Land Cruiser

3 Answers

Remove rear brake drums


0f2c8a8.gif
1. After removing the wheel, remove the brake drum. 2. Remove the shoe hold down spring, the automatic adjuster spring and adjuster lever.
7b7d17f.gif
3. Spread the shoes and remove the shoe adjuster. 4. Remove the shoe to shoe spring and shoe hold down spring.
a1a62c3.gif

Jun 03, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
2002 Hyundai Accent Logo

426 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...