Question about 2004 Chevrolet TrailBlazer

2 Answers

Replacing headlights Does it take a special tools to replace the front headlights? Can I change this myself?

Posted by on

  • Anonymous Dec 14, 2008

    How you do you replace a headlight on a 2004 TrailBlazer? Can't seem to get the plastic cover off?

  • dolphinfan Apr 04, 2009

    how do u change headlight

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

There are two clips for each light; one to each side just lift up on the clips. Then you have four upper and two lower grill clips that are the push/pull type. Just pull where the clips are located and they will pull right out. Watch for stressing the wiring going to the running lights. You then can pull the headlight grill assy out far enough to change the lights. Low beams are to the outside and high beams to the inside. DON'T TOUCH THE BULBS!!! A little twist left or right will unlock the bulbs. Use some contact grease to make sure the contacts stay good. 15 - 20 minute job.

Posted on Dec 21, 2008

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 54 Answers

It doesnt take special tools to do that. You might have to buy a couple of tools, but it wont cost much. Its relatively easy taking out your headlights.

Posted on Nov 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What tool is needed to replace a headlight bulb in a Kia Amanti


Some cars are a complete b r t d to change headlight bulbs. You may need to remove the headlight unit, to do this may require the removal of the bumper. Ask a main dealer for a quote, then winge, they may explain why the cost is so high.

Jul 05, 2016 | Kia Amanti Cars & Trucks

1 Answer

How to change left turn signal bulb


Rear. 2 retainers PLUS a very tight ball socket holding the light assembly into place. Be ready to catch the tail light when you pop it of the ball socket.
Front. Use the headlight removal tool in the tool kit. Open front bonnet and push down and remove tear shape trim on headlight side in question. Place headlight tool onto spline and with one hand ready to "catch" the headlight, turn the tool until headlight pushes forward. Then remove headlight by hand and replace globe as required. Be careful of bayonet fitting. Can be fragile.

Feb 18, 2010 | 2004 Porsche Cayenne

1 Answer

How to change the brakes on an 2005 Audi A6 I know you need a special tool to change the rear pads. But I only want to change the front pads. Is this something I can do myself or do I need to take to Audi...


The front pads are like all other cars, a rachet and a C Clamp. The special tool is sold at your local parts store, its a box with tips on it, as they screw in.

Sep 24, 2009 | 2005 Audi A6

1 Answer

Trying to replace light bulbs, front and rear


No usually for GM vehicles there are two pins on the headlight that you pull out and up. they are L shaped upside down. If not there are bolts holding the headlights on. But no special tool needed, it is a simple job, once the headlights are off twist the bulb counter clock wise, if they have a notch depress it and remove the bulb unhook it from the harness and you are done. Installation is reverse of removal.

Jul 06, 2009 | 2003 Pontiac Montana

1 Answer

Driver light out how to replace bulb need special tools?


Headlight Bulb Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the headlight assembly mounting screws.
  3. Pull the assembly forward and disconnect the bulb connector.
  4. Turn the bulb retainer ring counterclockwise and remove the bulb from the headlight assembly.
To Install:
NOTE: Do not handle the glass portion of the bulb with your bare fingers.
  1. Install the bulb in the headlight assembly.
  2. Install the retainer ring.
  3. Connect the connector to the bulb.
  4. Install the headlight assembly in the vehicle.
  5. Connect the negative battery cable.
No special tools required.

Jun 24, 2009 | 2004 Dodge Caravan

1 Answer

Procedures for replacing front shocks/struts on 1985 bmw 325e


are you changing the strut cartridge or the whole spring unit? if you are installing the whole unit, spring and all you will need no special tools, if not you will need a spring compressor

Apr 06, 2009 | BMW 325 Cars & Trucks

1 Answer

Transmission noise


There are no special tools to change the fluid. You have to make sure when you pull the filter off that the rubber seal comes out with it where it goes up into the trans. case. If not, you have to take a ice pick or something similar and pull that seal out. Put your new filter in, change the fluid. I would recommend putting a conditioner like Lucas trans. additive. Also, the clunking noise - you should check your axles and front motor mounts. Hope this helps. Phil

Jan 18, 2009 | 2005 Chevrolet Cavalier

1 Answer

Front wheel bearng replacement


hi i am rather family with this type of jag and the wheel bearings can be a bit tricky and you was right special tools to do the job are reqiered my advice is let a proffesional mechanic do the job it will save you a lot of hastle

dean

Sep 10, 2008 | 1998 Jaguar XJ8L

2 Answers

Replace front head lihgt bulsbs on 350 z


you should be able to access the connector and bulb without removing headlight assembly. lift the hood and you should see the connector behind the headlight.

Aug 29, 2008 | 2003 Nissan 350Z

1 Answer

Diy oil change 1996 c220


Need special tool to remove filter, be careful replacing it...

Jul 03, 2008 | 1996 Mercedes-Benz C-Class

Not finding what you are looking for?
2004 Chevrolet TrailBlazer Logo

583 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...