Question about 2000 Dodge Ram 1500 Truck

1 Answer

No front brakes on 94 dodge 4x4 1/2 ton

I have replaced all the brake parts front and back, have had a mechanic look at it and still don,t have front brakes. there is no more parts to replace. If you have a solution I sure would appreciate it. Thanks much.

Ut

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    Did you crack a line at master cylinder to front brakes to check for flow ? Follow on from there if you have flow.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 362 Answers

Is your abs light on. sometimes the anti lock brakes malfunction, if fkuid comes out when bleeding the front brakes then you probably have a leak the master cyl has a plastic resivior. look at the vase of the tank where it plugs into the master if you move it and see fluid you are leaking bexause of the wrong part. sen this a lot. also if no fluid comes out when bleeding front brakes you have a bad rubber line. just some thing
s to check.

Posted on Dec 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust parking cable 99 dodge dakota -drum brakes


Unless you have replaced the cable, it should never need to be adjusted. If you can reach under the vehicle, and when wiggling the parking brake cable, if it is taut (not sagging), then it is probably adjusted properly. What usually causes the parking brake cable to appear mis-adjusted (the parking brake won't hold the vehicle), is that the self-adjusters in the rear drum brakes are not working properly. This is bad because it means that you are not getting proper braking from the rear brakes as well as having the parking brake issue. This can cause premature wear to the front disc brake pads/rotors and affect braking power and control under certain stopping conditions. Front disc brakes work so well that many people never realize that their rear brakes aren't doing their fair share. The purpose of the self-adjusters in the drum brakes is to keep the rear brake shoes at a consistent distance from the drum's inner surface as the shoe lining wears down. If the adjuster works correctly, the parking brake will always stay in adjustment. You CAN adjust the parking brake cable, but if the problem is actually with the self-adjuster, you are masking the real problem, and later on when you need to replace the rear brake shoes, you will find it impossible to put the drum back on over the shoes as the parking brake will have the shoes pushed out too far. Have a mechanic check out the self-adjuster mechanism. It is always a good idea whenever you replace the rear brake shoes to replace all the rear brake hardware as well. You don't replace rear brakes nearly as often as the front ones, and the cost of the hardware is minimal in relation to the satisfaction of knowing that non-corroded parts will work better and provide longer service than the older, gummed-up and rusted hardware that is currently installed.

Sep 11, 2014 | Dodge Dakota Cars & Trucks

4 Answers

Front brakes sticking after a couple of miles


There are 2 causes, 1.caliper slides are in need of servicing/lube.2, caliper(s) piston(s) need to be serviced/cleaned. Recommend replacement of both calipers, if either doesn't work.

May 15, 2010 | Cars & Trucks

1 Answer

I need a diagram on front hub and brake assembly for 1999 dodge 1 ton dually 2 wheel drive. the front brake rotor is warped i need to replace it


8–Stud Rotor
  1. Raise and support the vehicle.
  2. Remove the wheel.
  3. Remove the hub extension.
  4. Remove the brake caliper assembly.
  5. Remove the axle nut cotter pin. Remove the axle nut.
  6. Disconnect the ABS wheel speed sensor wire from under the hood. Remove the sensor wire from the frame and steering knuckle, if equipped.
  7. Back off the hub/bearing mounting bolts 1/4 inch each. Then tap the bolts with a hammer to loosen the hub/bearing mounting bolts.
  8. Remove the bolts and remove the hub/bearing assembly.

Sep 16, 2009 | 2000 Dodge Ram 3500

1 Answer

Need to replace front rotors and brake pads


All you have to do is take off your calipers and the rotor will slide right off. Use a C clamp to push the piston of the caliper back in so you can put your new brakes on.

May 08, 2009 | 1994 Jeep Wrangler

1 Answer

1996 Dodge 4x4 1 ton leaking pasenger front seal how to replace?


if u have u joints there should not any fluid near your bearing other than grease... if it is leaking anything other than that it is probably brake fluid... i would suggest checking your brake cylinder and brake line leading along side the passenger side

Apr 21, 2009 | 1996 Dodge Ram 3500 Club Cab

2 Answers

Jerks while applying brakes


Yes if they are replacing both rotors and pads with premium parts.

Mar 30, 2009 | 2004 Dodge Stratus

1 Answer

Front disc brake pads on a 1997 dodge intrepid.


The Calipers on the Rotor that Hold the Brake Pads have Bolts on the Back Side at the Top and Bottom for Mounting. Just feel around back there and you will find them. Remove these and the Caliper will come right Off. Let me Know if you need more Help! Please Rate My Response! Thanks!

Jan 31, 2009 | 1997 Dodge Intrepid

1 Answer

94 4runner brake pressure.


did you possibly replace brake lines with standard instead of metric lines.The standard lines will fit but you will not get pressure back

Jul 20, 2008 | 1994 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...