Question about 2000 Jeep Grand Cherokee

1 Answer

Check engien lihgt with code p1762

Hi i have jeep grand cherokee year 2000 with check engien light with code p1762

Posted by on

  • Anonymous Feb 11, 2009

    2000 Jeep Grand Cherokee failed emissions test with error P1762 and P0441.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 185 Answers

CEL Code P1762 is Governor Pressure Sensor Offset Improper Voltage. Make sure all your wires going to the sensor are ok, then if they are I would look into a new Sensor. Hope this gives you some direction. Thanks for Using FixYa!

Sincerely,

JC

Posted on Nov 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a code p1762 for my 97 jeep grand cherokee


Trouble code P1762 means: Governor pressure sensor offset improper voltage. Gov. Pressure Sensor.It is located in the valve body of the transmission and requires dropping the transmission pan to replace. Sounds much more difficult than it is. Since you have to change your fluid it's a good idea to change the trans. filter .

Feb 01, 2011 | 1997 Jeep Grand Cherokee

1 Answer

Code p1762 govenor pressue sensor offset volts


P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Dec 14, 2010 | 2001 Jeep Grand Cherokee

2 Answers

Shifting Problems on Jeep Grand Cherokee


Your Kick down cable is either on too short or come off completely. Check that first before you spend any money on anything else or transmission overhaul

Aug 09, 2009 | 2001 Jeep Grand Cherokee

2 Answers

Diagnostics "P1762 Manufac. Contrl. Transmission"


Had the same code on my 2002 Jeep Grand Cherokee. Started having shifting problems as well. Code is for governor pressure sensor on trans. Cost me about $800 for dealer to fix. No problems after part changed out.

May 22, 2009 | 2002 Jeep Grand Cherokee

1 Answer

I have a ODB II code reader giving p1763, p1762, p0303


Your right about the two codes. It's really a transmission part.
As soon as you open up the transmission pan, it right there.
f0d99d5.jpg But, I would leave this up to a transmission place. It may need a special type of calibration tool for the new sensor.

As for PO303, that is a missfire in cylinder #3

I hope I answered your question.

Mar 27, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Code p1762 is appearing on my jeep dashborad


Governor Pressure Sensor Offset Volts Too Low or High

Mar 22, 2009 | 2004 Jeep Grand Cherokee

1 Answer

P1762


Looks like the fautl code refers to the stuck solenoid on the shift control valve which is in the valve body.
It is a job that requires lots of precision and probably if you take the valve body out you'll need a plan to reassemble it...I would suggest getting it to a specialist.
Cheers

Feb 02, 2009 | 2000 Jeep Cherokee

1 Answer

Engine code 95 jeep grand cherokee lerado


12 is a battery disconnect within the last 50 start cycles and 55 means the end of the diagnostic cycle.  Basically the computer found nothing wrong. The 12 code may seem incorrect if you haven't disconnected the battery recently, but from my experience the 12 code shows up almost all the time regardless.

Dec 16, 2008 | 1995 Jeep Grand Cherokee

1 Answer

2001 jeep grand cherokee transmission revving-codes p1757, p1762


P1757 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Above 3 PSI In Gear At 0 MPH Conditions: Engine started; vehicle driven to a speed over 30 mph, and the PCM detected the Governor Pressure Sensor was more than 3 psi with the requested pressure at 0 psi (95% duty cycle command) for 2.65 seconds. The fault must occur twice on one trip to set the code. Possible Causes: Check for the presence of other A/T related trouble codes Governor pressure Sensor is damaged or has failed Governor pressure Sensor VREF (5v) circuit is open or shorted Transmission valve body is leaking, damaged or has failed PCM has failed P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Nov 17, 2008 | 2001 Jeep Grand Cherokee

1 Answer

2000 Grand Cherokee 4.0 liter 2wd


PULL THE TRANSMISSION PAN TO SEE IF THE IS ABNORMAL CLUTCH MATERIAL IN THE PAN. IF EXCESSIVE AMOUNTS ARE NOT PRESENT THAN THE PROBLEM SHOULDN'T BE TOO SEVERE. WAS THE FAULT CODE FOR VOLTS TOO HIGH OR TOO LOW?

Sep 25, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

1,520 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...