Question about 1997 Buick Park Avenue

1 Answer

Replacing rear brake shoes

How do i install rear brake shoes on 1997 buick park avenue

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Http://www.2carpros.com/how_to/rear_brake_pads.htm

heres instructions with pictures! ;) hope this helps!! craig

Posted on Aug 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i tighten the parking brake on an 91 buick park ave ultra?


check to make sure the rear brake shoes are adjusted before adjusting park brake cable. pull the brake drum off and inspect brake shoes before adjusting

Sep 14, 2012 | 1991 Buick Park Avenue

1 Answer

1992 Buick Park Avenue - BRAKES


Yep need to know weather it is drum brakes or disc brakes.

Oct 21, 2011 | 1992 Buick Park Avenue

1 Answer

Help with installing brake shoes on 1993 buick park ave


Your Buick has front disc brakes...and rear drum brakes...the usual concern is the front pads as they are used more...these are the easiest pads to replace...as you only need to remove the caliper from the rotor with 2 bolts to lift off...Be sure to push the piston all the way back into the caliper to install new pads...rotors are pop offs too...The rear drum is different...the brake shoes are held on with clips and springs...try keeping one of the shoe assemblies intact while you switch out the other shoes...be sure to inspect the rear wheel brake cylinders for possible leaking...usually an oil build up inside the brake drum...these are inexpensive and should be switched out on a 93 Buick...:) Hope this helps.

Apr 02, 2011 | 1993 Buick Park Avenue

1 Answer

I need a diagram of the rear brakes of a 1997 Intrepid Chrysler-where can I get one>


If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision
  1. Remove the rear wheels and brake drums.
  2. Remove the dust cap from the rear hub and bearing assembly.
  3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
  4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
  5. Remove the automatic adjuster spring from the adjuster lever.
  6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
  7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
  8. Remove the both lower brake shoe to anchor springs.
  9. Remove the 2 brake shoe hold-down springs from the brake shoes.
  10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
  11. Separate the brake shoes from the automatic adjuster mechanism.
  12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
  13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
  14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
  15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
  16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
  17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
  18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
  19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
  20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
  21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
  22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
  23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
  24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.
prev.gif next.gif

Sep 03, 2010 | 1997 Dodge Intrepid

2 Answers

Parking brake cable stretched beyond adjustment how do you replace


Rear Brake Shoes- You'll need to know how to remove the rear brake shoes to remove the parking brake cable. REMOVAL AND INSTALLATION Amigo and Rodeo
  1. Raise and safely support the vehicle.
  2. Remove the rear wheels.
  3. Remove the brake drums.
  4. Remove the brake return springs.
  5. Remove the leading shoe holding pin and spring, and then the leading shoe.
  6. Remove the self-adjuster and the adjuster lever.
  7. Remove the trailing shoe holding pin and spring.
  8. Disconnect the parking brake cable from the trailing shoe and remove the trailing shoe. Remove the parking brake lever from the trailing shoe. To install:
  9. Attach the parking brake lever to the trailing shoe.
  10. Connect the parking brake cable to the parking brake lever.
  11. Apply a thin coat of high temperature grease to the shoe contact points on the brake backing plate (locations A and C in the accompanying illustration), piston contact surface (B), and self-adjuster (D). Fig. 1: Exploded view of the rear drum brakes — Amigo and Rodeo 93026g56.gif

  12. Position the trailing shoe on the backing plate and install the hold-down pin, spring, and retainer. Don't stretch the return spring when fitting the shoes onto the backing plate.
  13. Connect the upper return spring and the leading shoe to the trailing shoe and position the leading brake shoe on the backing plate.
  14. Install the adjuster assembly and the hold-down pin, spring, and retainer.
  15. Use a brake spring tool to install the lower return spring.
  16. Install the self-adjuster lever and adjuster spring.
  17. Adjust the shoe-to-drum clearance to 0.0098–0.0157 in. (0.25–0.40mm) and install the brake drum.
  18. Check the brake drum for scoring or other wear. Machine or replace as necessary. Check the maximum brake drum diameter specification when machining.
  19. Install the rear wheels. Lower the vehicle.
  20. Road-test the vehicle.
prev.gif next.gif

Aug 17, 2010 | 1997 Isuzu Rodeo

2 Answers

1997 Ford contour rear brake shoe replacment help.


Brake shoe removel:

Depress and turn the retainers for the hold-down springs and pins to remove them from each shoe. Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.

Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.

Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xgUqun
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xdByQ8

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

    Jul 17, 2010 | 1995 Ford Contour

    1 Answer

    Remove and replace rear brake shoes on 2004 honda accord


    Brake Shoes Removal & Installation To Remove:
    1. Raise and safely support rear of vehicle.
    2. Remove rear wheel assemblies.
    3. Release parking brake.
    4. Remove brake drum.
    Rear brake shoe assembly


    6c57c70.gif
    1. Using an appropriate brake spring tool, unhook upper return spring from rearward brake shoe.
    2. Push retainer springs IN and turn to remove tension pins.
    3. Lower brake shoe assembly and remove lower return spring.
    4. Remove brake shoe assembly from back plate.
    5. Disconnect parking brake cable from lever and remove brake shoe.
    6. Remove parking brake lever from brake shoe.

    To Install:

    d36458c.gif
    1. Install parking brake lever to rearward brake shoe.
    2. Secure lever to brake show with a NEW U-clip.
    3. Pinch U-clip closed.
    4. Connect parking brake cable to rearward brake shoe.
    5. Install self-adjuster lever spring on front brake shoe.
    6. Assemble clevises, adjuster bolt and upper and lower return springs.
    7. Apply a light coat of grease (Molykote 44MA or equivalent) to sliding surfaces.
    8. Install brake shoe assembly onto back plate.
    9. Install tension springs.
    10. Using an appropriate brake spring tool, unhook upper return spring to rearward brake shoe.
    11. Install brake drum.
    12. Install rear wheel assembly.
    13. Lower vehicle.
    14. Adjust self-adjusting brakes by pressing brake pedal several times.

    Jul 13, 2009 | 2004 Honda Accord

    3 Answers

    How to change rear brake pads on 97 park avenue


    To change Rear Brake Pads on a 1997 Buick Park Avenue. Remove the bottom bolt on the caliper. The top has a non removable pivot pin. Remove the bolt that holds the brake emergency brake to the frame. Remove the 2 bolts in the rear of the axle plate that hold the caliper in place. (they take a #18 metric socket and you may need a breaker bar to loosen them) With the caliper free from the mount, swing the pad holder up on the top pivot pin and remove the old shoes and replace. Turn the caliper piston clockwise and inboard with a caliper disk brake tool (harbour freight about 19 bucks). Flip the shoe holder part of the caliper back in place and put the assembly back over the rotor. Re install the bolts (blue locktite on the caliper mount bolts and tighten slight snug with breaker bar) retighten the bottom caliper bolt (moderately no locktite)

    Mar 20, 2009 | 1997 Buick Park Avenue

    2 Answers

    2004 buick emergency brake


    This car has regular shoes on the back not disc. Replace shoes and adjust cable. No parking brake is a sign of worn out shoes. Regals have rear disc on them for this year.

    Feb 21, 2009 | 2004 Buick Century

    Not finding what you are looking for?
    1997 Buick Park Avenue Logo

    257 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Buick Experts

    yadayada
    yadayada

    Level 3 Expert

    60867 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Buick Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...