Question about 2000 Ford Focus

1 Answer

Service engine light / code is Fuel bank #2 running lean

I would like to know how to correct the problem?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem. After taking the MAF sensor off and cleaning it, it was still there... I ended up changing the throttle position sensor and all was well. It cost about 23 bucks..You can try this first.

Posted on Dec 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does code p1131 mean on a 2001 ford taurus


P1131 Ford
P1131 Ford - Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 1

Repair Importance Level: 3/3

Repair Difficulty Level: 2/3

http://engine-codes.com/p1131_ford.html

Forum Code

Possible causes

- Faulty Oxygen Sensor

- Vacuum leak affecting bank 1 only

- Fuel injector problem bank 1

- Check for cylinder misfire on bank 1

- Engine mechanical condition

Tech notes

Though the Oxygen (O2) sensor, the Engine Control Module (ECM) has detected a lean system, which means that there is either not enough fuel or and excessive amount of air in the system. Start by checking for vacuum leaks.

When is the code detected?

The Engine Control Module (ECM) detected bank 1 oxygen (O2) at its lean limit

Possible symptoms

- Engine Light ON (or Service Engine Soon Warning Light)

P1131 Ford Description

A Heated Exhaust Oxygen (HO2S) sensor indicating rich at the end of a test is trying to correct for an over-lean condition. The test fails when the fuel control system no longer detects switching for a calibrated amount of time.

Read more: http://engine-codes.com/p1131_ford.html#ixzz3izk89wMu

Aug 16, 2015 | Ford Cars & Trucks

1 Answer

Down to the final OB code on my truck...Po174


P0174 FORD - Fuel Injection System Too lean Bank 2xicon.jpghttp://engine-codes.com/p0174_ford.htmlForum CodePossible causes- Intake air leaks
- Faulty front heated oxygen sensor
- Ignition misfiring
- Faulty fuel injectors
- Exhaust gas leaks
- Incorrect fuel pressure
- Lack of fuel
- Faulty Mass Air Flow (MAF) sensor
- Incorrect Positive Crankcase Ventilation (PCV) hose connection Tech notes The codes is usually set when there is an intake leak after the air flow meter, before replacing any parts check for loose or broken hoses and intake gasket leak. On Ford some models dirty air filter, and dirty or faulty air flow sensor are the cause of the problem.

It's a very common problem for the Ford Windstar. Here a link to a web site with information how to repair:
When is the code detected?- Fuel injection system does not operate properly.
- The amount of mixture ratio compensation is too small. (The mixture ratio is too lean.) Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Excessive Fuel ConsumptionP0174 FORD Description The Powertrain Control Module (PCM) monitors the engine Air/Fuel mixture ratio, the actual mixture ratio can be brought closely to the theoretical mixture ratio based on the mixture ratio feedback signal from the heated oxygen sensors 1. The PCM calculates the necessary compensation to correct the offset between the actual and the theoretical ratios.

In case the amount of the compensation value is extremely large (The actual mixture ratio is too lean.), the PCM judges the condition as the fuel injection system malfunction and light up the engine light.

Oct 08, 2012 | Cars & Trucks

2 Answers

I have a 2001 Jimmy with "Service Engine Soon"


P0171 System too lean bank 1
P0174 System too lean bank 2

Last time you changed your fuel filter?
Look for any vacuum leaks.

Sep 05, 2011 | 2001 GMC Jimmy

2 Answers

2000 Lincoln Navigator - few days ago started idling very rough when truck is at a stop or in park. Service Engine Light came right around time I noticed that it was idling rough when stopped. Following...


P1131 Lack of HO2S-11 Switch ,Sensor Lean
P1151-Lack of HO2S-21 Switch ,Sensor Lean
PO171- System to Lean (Bank 1)
PO174-Systen to Lean (Bank 2)

Fuel Filter -Plugged
Low Fuel Pressure
Evap System -Leaks
Leaks - in ducting,air filter to throttle
PCV -Leaks
Exhaust System -Leaks
O2 Sensors-worn out

Apr 06, 2011 | 2003 Lincoln Navigator

1 Answer

Rough idle vibrates and po171 code service engine soon. jamesrowland9@aol.com


Hi, a Ford P0171 is a LEAN code for cylinder bank 1, and P0174 is a LEAN code for cylinder bank 2. These codes commonly occur on many Ford vehicles, and are set when the powertrain control module (PCM) sees the air/fuel mixture is running too lean (too much air, not enough fuel).
When the Check Engine Light comes on, either one of these codes, or both, may be found when a code reader or scan tool is plugged into the vehicle diagnostic connector. IF the vehicle is driven long enough, typically both codes will be set.
A P0171 lean code for bank 1 is the cylinder bank on the RIGHT (passenger) side of the engine on Ford vehicles with a V6 or V8 engine and rear-wheel drive.


A lean fuel condition may exist if the engine is sucking in too much air and/or the fuel system is not delivering enough fuel. If bad enough, a lean fuel condition may cause lean misfire, a rough idle, hesitation or stumble when accelerating, and/or poor engine performance.
Unmetered air can enter the engine through a vacuum leak, a dirty airflow sensor that is not reading airflow accurately, an EGR valve is not closing and is leaking exhaust into the intake manifold, an EGR valve that is allowing too much flow (because the EGR differential pressure sensor that monitors EGR flow is faulty and is under-reporting EGR flow).
If the problem is not enough fuel, the underling cause may be a weak fuel pump, restricted fuel filter, leaky fuel pressure regulator or dirty fuel injectors.

Mar 24, 2011 | Ford Escort Cars & Trucks

1 Answer

I have a 1998 ford contour that has codes p1130 and p1131 on it what could be the problem. the check engine light is on


H40 DTCs P1131, P1132, P1151 AND P1152: UPSTREAM HO2S NOT SWITCHING. DTC P1130: FUEL SYSTEM NOT SWITCHING AT FUEL TRIM (RICH OR LEAN)
    Diagnostic Trouble Codes (DTCs) P1131 bank 1 (Cylinder 1) and P1151 bank 2 indicate the fuel/air ratio is correcting rich for an overly lean condition. The HO2S voltage is less than 0.45 volt. DTCs P1132 bank 1 (Cylinder 1) and P1152 bank 2 indicate the fuel/air ratio is correcting lean for an overly rich condition. The HO2S voltage is greater than 0.45 volt.
    DTC P1130 and P1150 indicate the fuel control system has reached maximum compensation for a lean or rich condition and the HO2S is not switching.
    DTC/HO2S Reference List
    • HO2S-11 = DTCs P1131, P1132 and P1130
    • HO2S-21 = DTCs P1151, P1152 and P1150
    Possible causes:
    Fuel system
    • Excessive fuel pressure.
    • Leaking fuel injector(s).
    • Leaking fuel pressure regulator.
    • Low fuel pressure or running out of fuel.
    • Contaminated fuel injector(s)
    • Vapor recovery system
    Induction system
    • Air leaks after the MAF.
    • Vacuum leaks (vacuum lines and gaskets).
    • Restricted air inlet.
    • PCV system.
    • Improperly seated engine oil dipstick.
    EGR System
    • Leaking gasket.
    • Stuck open EGR valve.
    • Leaking diaphragm.
    Base engine
    • Oil overfill.
    • Cam timing.
    • Cylinder compression.
    • Exhaust leaks before or near the HO2Ss.
  • Check intake air system for leaks, obstructions and damage.
  • Check air cleaner element, air cleaner housing for blockage.
  • Verify integrity of the PCV system.
  • Check for vacuum leaks.

Feb 12, 2011 | Ford Contour Cars & Trucks

1 Answer

What does it mean when your bank 1 n bank 2 are running lean


A lean bank 1 and 2 is indicating there is not enough fuel being injected to support proper combustion.
Leading causes can include but are not limited to......
1) low fuel pressure or plugged fuel filter.
2) vacuum leak causing lean condition.
3) air intake hose or crank case not sealed properly and bypassing the MAF sensor or the MAF sensor element is dirty.
4) wrong fuel or poor quality fuel used.
Hope this helps. If the Service Engine Soon light is illuminated, there will be fault codes associated the light. Get the vehicle scanned for free at your local Auto Zone or Advanced Auto and report back.

Nov 25, 2010 | 2003 GMC Yukon XL

1 Answer

Codes


Your sensors are reading correctly so leave them alone. What you have is a fuel delivery issue. Your MAF sensor is telling your engine to lean your fuel mixture. You need to remove and clean or replace (is better) the MAF. But first replace your PVC valve and clean your ERG valve.

Jan 20, 2010 | 2000 Dodge Intrepid

4 Answers

Check Engine light is on my 1997 F150 with a small V-8. The tester returns codes P0171, P0172, P0174 and P0175. What does all this mean?


those codes are for lean engine condition look for vac leaks at the back of engine to the pcv valve could hear hissing noise with engine running also check egr valve to be stuck open also when was last fuel filter changed? hope this helps .

Sep 16, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Engine light on 3 codes in system


The lean running codes are related to the p-1000 code...

Running lean on bank 1 and bank 2 means your oxygen sensors sense too much oxygen in your exhaust flow. This means either your engine is getting unmetered air (air that the engine does not know is coming in, therefore does not send fuel to compensate for...) (air that your mass air flow sensor does not see). You could have either a bad mass air flow (MAF) sensor (in the intake piping after the filter; this sensor tells your engine how much air it's taking in, so it can send the right amount of fuel through the injectors to properly burn with the air available with as little emissions as possible), or you could also have a cracked/broken intake piping after this sensor which lets air in the intake that the sensor does not measure... A large vacuum leak could also let unmetered air in the engine.

Or... Another possibility here would be low fuel pressure (bad fuel pump, bad fuel pressure regulator, fuel leak), as not enough fuel for the air would also cause the same lean condition.

It could be that some oxygen sensors are bad...

These conditions are hard to pinpoint exactly unless you have a scanner that can read sensor data (MAF Flow, fuel pressure, oxygen sensor values)...

The first thing I'd do would be to check for cracks or damage in the intake piping... If there is none, then it might be a low fuel pressure issue, or sensor problems...

May 08, 2009 | 2003 Jaguar X-Type

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...