Question about 2004 Jeep Wrangler

3 Answers

Floor shifter ont engage to park

I have a 2004 Jeep Rubican and the floor shifter suddenly cant be put into park. When lifting up the console for the shifter the pin that attaches to the handle was not pushing far enough into the gears. Do I need to purchase the entire floor shifter or can I get a replacement part?

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

YES THE PART THAT IS BROKEN IS MOST LIKELY A WHITE PLASTIC PIECE THAT SITS INSIDE THE SHIFTER HOUSING, REMOVE THE SHIFTER HANDLE REMOVE THE WHITE PLASTIC PIECE WITH ALL THE ROUND BALLS ON IT (I KNOW WHAT IT LOOKS LIKE YOU DONT HAVE TO SAY IT) AND LOOK DOWN THE HOUSING WITH A FLASHLIGHT IF YOU STILL SEE A PART OF THAT WHITE PLASTIC PIECE, THATS YOUR PROBLEM. YOU CAN EITHER REPL SHE SHIFTER LEVER P# 52078551AG OR SEARCH THE JUNK YARDS FOR THAT PART

Posted on Jan 05, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 86 Answers

If you are sure that the problem is only the shifter's pin and you have a mechanic who specialize in transmission, replacement parts would be enough.

Posted on Nov 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do I get a stuck key out of an ignition lock cylinder on a 2006 chevy impala 3.9 motor


Does it go into the lock position ? Will the shifter go into the park position ? Is it a automatic transmission ?
Electronic Park Lock (EPL)/Ignition Lock Cylinder Control Actuator: If the vehicle is equipped with automatic transmission and a floor mounted console gear shift, it has an ignition lock cylinder control actuator system in the steering column. The ignition lock cylinder control actuator purpose is to prevent the ignition key from being turned to the OFF position when the transmission is in any position other than PARK and the vehicle may still be moving. The column ignition lock system consists of an ignition lock cylinder control actuator, and a park position switch that is located in the automatic transmission shift lock control switch. The ignition lock cylinder control actuator contains a pin that is spring loaded to mechanically prevent the ignition key cylinder from being turned to the lock position when the vehicle transmission is not in the PARK position. If vehicle power is lost, and/or the transmission is not in the PARK position the operator will not be able to turn the ignition key to the lock position and will not be able to remove the ignition key from the column.
There should be a hole in the bottom of plastic steering cover or a rubber cover that comes out . you can stick your finger up there an there is a button you push that will allow you to take out the key !
2006 chevy cobalt How to fix key being stuck in the ignition 2006 Impala shifter problems

Apr 08, 2015 | 2006 Chevrolet Chevrolet Impala LT

1 Answer

Jeep wrangler 2005 automatic floor gear shifter is loose won't engage stuck in park


try pushing the knob down onto the shifter a little bit then try and shift. Sometimes if that knob is raised even a little bit it will be locked in park. Can't be 100% sure without seein it but worth a shot. Hope that helps you.

Oct 02, 2012 | Jeep Wrangler Cars & Trucks

1 Answer

How do you disassemble the counsil?


Front Floor Console Replacement Removal Procedure
1. Remove the console trim plate. 2. Remove the left console trim panel. . 3. Remove the right console trim panel. 4. Remove the floor console compartment.
1356712.gif
5. If equipped with an automatic transmission, remove the 4?screws?(1), attaching the console?(2) to the shifter assembly?(3).
1356713.gif
6. If equipped with a manual transmission, use a flat-bladed tool to disengage the retaining tabs?(1) attaching the manual transmission shifter boot assembly?(2) to the console. 7. Remove the manual transmission gear shifter knob, if necessary. 8. Remove the manual transmission shifter boot assembly?(2) from the shifter, if equipped.
1356714.gif
9. Disconnect the console wiring connector?(1) from the inner console.
1356717.gif
10. Remove the two nuts?(1) attaching the floor console?(3) to the vehicle floor. 11. Remove the two screws?(2) attaching the front of the console to the instrument panel assembly. 12. Remove the accessory power receptacle. 13. Lift the rear of the console upward and remove from the vehicle. 14. Remove the floor console armrest hinge, if necessary. 15. Remove the center console end panel.
1356777.gif
16. Remove the screw?(2) attaching the floor console rear air duct?(3) to the floor console?(1). 17. Remove the floor console rear duct?(3) from the floor console?(1). 18. Remove the console storage bin, if necessary. 19. Remove the console lamp. 20. Remove the console compartment lamp switch.

Oct 06, 2011 | 2005 Pontiac GTO

2 Answers

How do you remove a rear cupholder tray in a 2003 Jeep Grand Cherokee?


Hello
In order to remove the rear passenger cup holder you must remove the console from the car and turn it over to gain access to the retainers that hold the cup holder into the console. If you go to the page at the web link below you will find detailed instructions with pictures (click on the pictures to enlarge them) on how to remove the console assembly from the floor.

http://www.wjjeeps.com/console.htm

Jun 06, 2011 | 2006 Jeep Grand Cherokee

2 Answers

How do I adust the emergency brake


There is an adjuster under the console. See instructions below from autozone.com:

    1. On vehicle with low series floor console:
    1. If equipped, remove the manual transmission shift knob by turning counterclockwise.
    2. Remove the floor console front finish panel.
    3. Apply the parking brake, then remove the floor console rear finish panel.

    1. On vehicle with high series floor console:
    1. Apply the parking brake.
    2. Remove the floor console finish panel.

    1. Remove the adjustment nut clip.
    2. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled.

      0996b43f80204da9.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled
    3. Confirm the parking brake is applied.
    4. Install the adjustment nut clip.
    1. On vehicles with high series floor console:
      1. Install the floor console rear finish panel.

    1. On vehicles with low series floor console:
    1. Install the floor console rear finish panel.
    2. Install the floor console front finish panel. If equipped, install the manual transmission shifter knob by turning clockwise.
  • Sep 12, 2010 | 2004 Ford Escape

    2 Answers

    04 Navigator gear shift button broken


    I only have 2003 Nav procedure. Maybe get used part at car-part.com. Page with * is lowest price.

    SECTION 307-05: Automatic Transaxle/Transmission External Controls 2003 Expedition/Navigator Workshop Manual
    REMOVAL AND INSTALLATION Selector Lever —Floor Shift Removal and Installation
    1. Lift the floor shift PRNDL bezel.
    1. Disconnect the PRNDL bezel wire harness connector.
    1. Remove the shift lever handle and cover.
      1. Slide the handle bezel down.
      1. Remove the screw.
      1. Disconnect the TCS wire harness.
      1. Lift assembly from the shifter lever.
    b038436.gif
    1. Position the window regulator control panel aside.
    1. Remove the screws and the console finish panel.
    1. Remove the left side console access panel.
    1. Disconnect the transmission shift cable from the transmission selector arm.
    1. Remove the transmission shift cable retaining clip from the floor shift mechanism through the console access.
    1. Remove the four bolts retaining the floor shift mechanism to the floor.
    1. Disconnect the floor shift mechanism wire harness connector.
    1. Remove the floor shift mechanism from the console.
    1. Remove the brake shift interlock actuator, parking brake release mechanism and harness.
      • Remove the wire harness retainers.
      • Remove the wire harness retainers.
      • Remove the two screws retaining the brake shift interlock assembly.
      • Remove the two screws retaining the parking brake controller.

    Mar 15, 2009 | 2004 Lincoln Navigator

    1 Answer

    How can i find out my parking brake adjustments on my 2003 ford escape?


    Parking Brake Cable Adjustment Vehicle with low series floor console
    1. Remove the floor console front finish panel.
      1. If equipped, remove the manual transmission shift knob by turning counterclockwise.
      1. Remove the floor console front finish panel.
    1. Remove the floor console rear finish panel.
      1. Apply the parking brake.
      1. Remove the floor console rear finish panel.
    Vehicle with high series floor console
    1. Remove the floor console finish panel.
      1. Apply the parking brake.
      1. Remove the floor console finish panel.
    All vehicles
    1. Remove the adjustment nut clip.
    1. Turn the parking brake control adjustment nut so that the parking brake control stroke is three to five notches when pulled.
    1. Confirm the parking brake is applied.
    1. Install the adjustment nut clip.
    Vehicle with high series floor console
    1. Install the floor console rear finish panel.
    Vehicle with low series floor console
    1. Install the floor console rear finish panel.
    1. Install the floor console front finish panel.
      • If equipped, install the manual transmission shifter knob by turning clockwise.

    Jan 21, 2009 | 2003 Ford Escape

    2 Answers

    NEED TO LOCATE THE SHIFT CONTROL RELAY ON 2004 F150. CAN'T MOVE THE SHIFTER OUT OF PARK.


    If it is a floor shift. under console on shift mechanism
    column shift, on column towards floor

    Dec 31, 2008 | 2004 Ford F150

    1 Answer

    98 Chevy K1500, four wheel drive floor shifter won't engage.


    I had the same problem with my 98 z71, I put the floor shifter in neutral, and let the truck roll backwards a little bit, BE CAREFUL, with the floor shifter in neutral the truck will roll, regardless if the shifter on the steering column is in Park, use caution, make sure there is no one around your truck and you are inside of it and out of the path of doors and tires,

    Dec 15, 2008 | 1998 Chevrolet K1500

    Not finding what you are looking for?
    2004 Jeep Wrangler Logo

    Related Topics:

    300 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...