Question about 1995 Dodge Ram

1 Answer

Will not start

I can start it only if i have the foot on the gas ,when i take foot of the gas it stalls? when warmed up it some times idles for a few moment then stalls.so in a note i have been two foot driving .

Posted by on

  • yellowdragon Nov 29, 2008

    I AM SORRY I DONT KNOW WHAT a . i . s motor is

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,674 Answers

Try pulling your A.I.S. Motor off & cleaning it and the port it came out of, as well as the connector.

Posted on Nov 29, 2008

  • Mike Butler
    Mike Butler Nov 29, 2008

    AIS or IAC motors are same thing, they adjust your idle speeds for you under different conditions. Not a gaurantee but for $5 or $10 that's where I'd start. Get yourself a can of throttle body cleaner, and give the inside of the throttle body a good cleaning, as well. Spray the cleaner in the port that the motor comes out of & clean the shaft & tip of motor good.make sure the connection has clean terminals too, spray them with contact cleaner. Here's a link so you can scroll down the page and see a picture of what your looking for. ( http://www.autozone.com/shopping/repairG... )

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I put in another battery in my 2000 dogde truck.now it wont idle on its own.


Robert, You may have to try this relearn procedure.
Warm the engine, but hold your foot on the throttle as necessary to keep the engine running.
  1. With vehicle in Park, slowly release the throttle so that the engine will idle on its own. You may have to work at this a bit.
  2. Let the engine idle on its own for about one minute.
  3. Continue to let the engine idle and with your foot on the brake, place the transmission in Drive and let the engine idle for another minute.
  4. Continue to let the engine idle with your foot on the brake and the transmission in Drive. Turn the A/C on and let the engine idle for another minute with the A/C compressor running.
  5. Turn the ignition off and wait a minute. Check the attached links,
    "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Battery Disconnect or Replacement Problems

https://ca.answers.yahoo.com/question/index?qid=20100517211203AAw91qa

http://www.automotiveforums.com/t454660-click_here_for_instructions_on__quot_how_to_idle_relearn_quot_.html

The Dodge Relearn Procedures eHow

Mar 10, 2016 | Cars & Trucks

1 Answer

97 dodge caravan start and stall in morning, if warm up 5-10 minutes then no driving problem. if warm up not enough the van will lose idling and stall at stop sign or when my foot is leaving the gas pedal....


The choke function is not working on a cold engine.
1 clean throttle body and IAC motor air pathways.
2. Check for engine codes, you are looking for a code that relatws to the wngine temperature sensor.

Sep 26, 2017 | 1997 Dodge Caravan

1 Answer

Car stalls after warm on hot day after a few stops. will stall when stopping at intersections, and when taking foot off the gas going down hills.


The idling setting in the car is not set correctly or the idling is LOW due to fault in the setting.
You will need to check if the throttle position is correct and the idle setting WITH THE CLUTCH PRESSED must be of the CORRECT IDLING RPM. If not reset the position after cleaning the system.

Aug 09, 2011 | 2002 Ford Taurus

1 Answer

Car idles low, stalls after start


Common issue at the shop (i'm a ford technician), here is what I do to correct it.
Here is the most common cause of surges and stalls at stops and low erratic idle speed and rough idle, it is the idle speed control air-bypass valve and throttle valve (IAC for short), they get full of gunk over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Mar 11, 2009 | 1999 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...