Question about 1995 Dodge Stratus

1 Answer

How do you take off crankshaft pulley on a 95 dodge stratus?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Take off center bolt and then you buy a crank dampner puller from snap-on, mac , or you may try auto zone or checker, but the tool trucks like snap on have them

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I set the timing on a 1996 dodge stratus 2.4l engine


  1. Using sprocket installation tool No. 6792 or equivalent, press the crankshaft sprocket onto the crankshaft.
  2. Install the camshaft sprockets onto the camshafts. Install and tighten the sprocket retaining bolts to 75 ft. lbs. (101 Nm).


0900c152800896f5.jpg
enlarge_icon.gifenlarge_tooltip.gif
Fig. Fig. 4: Proper camshaft sprocket alignment for timing belt installation

  1. Install the crankshaft sprocket. Set the crankshaft sprocket to Top Dead Center (TDC) by aligning the notch on the sprocket with the arrow on the oil pump housing.
  2. Set the camshafts to align the timing marks on the sprockets.
  3. Move the crankshaft to 1 / 2 notch before TDC.
  4. Install the timing belt starting at the crankshaft, then around the water pump sprocket, idler pulley, camshaft sprockets, and then around the tensioner pulley.
  5. Move the crankshaft sprocket to TDC to take up the belt slack.
  6. Install the tensioner to the engine block, but do not tighten.
  7. Using a torque wrench on the tensioner pulley apply 250 inch lbs. (28 Nm) of tighten to the tensioner pulley.
  8. With torque being applied to the tensioner pulley, move the tensioner up against the tensioner pulley bracket and tighten the fasteners to 275 inch lbs. (31 Nm).
  9. Remove the tensioner plunger pin. The tension is correct when the plunger pin can be removed and replaced easily.
  10. Rotate the crankshaft 2 revolutions and recheck the timing marks. Wait several minutes and then recheck that the plunger pin can easily be removed and installed.
  11. Reinstall the front timing belt cover(s).
  12. Reinstall the engine mount bracket.
  13. Reinstall the right engine mount.
  14. Remove the floor jack from under the vehicle.
  15. Install the crankshaft damper and tighten to 105 ft. lbs. (142 Nm).
  16. Install the accessory drive belts and adjust to the proper tension.
  17. Install the right inner splash shield.
  18. Reconnect the negative battery cable.
  19. Check for leaks and proper engine operation.

Source: Autozone.com

May 22, 2013 | 1996 Dodge Stratus

1 Answer

How do i get the crankshaft pulley off


The crankshaft pulley is "press-fitted" onto the crankshaft. A special cranshaft pulley remover tool is required to remove it. (See picture below)

Many parts retailers like AutoZone and Advance Auto have this tool available as a "loaner" or "rental".
The loaner programs usually require you to pay the purchace price of the tool up front, then will give you a FULL refund when you return the tool to the store.


10_11_2011_12_20_31_pm.jpg

Oct 11, 2011 | 2001 Dodge Stratus

1 Answer

Its actually a "95" stratus,


The crankshaft position sensor on the 2.5 V6 is located on the transaxle
bellhousing below the distributor.

Mar 05, 2011 | 1998 Dodge Stratus

1 Answer

How to Align the timing marks after replacing the timing belt 0n 2002 dodge stratus 2.4 dual cam


should be a mark for top dead center on the crankshaft and the pulley where the belt goes...line them up

Aug 15, 2010 | 2002 Dodge Stratus

1 Answer

How do you remove the crankshaft from 2004 dodge


What size engine. You want to know how to remove the crankshaft pulley right?

Jul 04, 2010 | 2004 Dodge Stratus

1 Answer

I can't get the crankshaft damper pulley off of a 2000 Dodge Stratus, 2.4L, DOHC. My end goal is to remove the timing belt. I have already removed the accessory drive belts, but cannot remove the...


Download this link and find your Service manual for your vehicle. It will serve you well and to keep for future reference

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

May 02, 2010 | 2000 Dodge Stratus

1 Answer

How do you remove the crankshaft pulley on a 1998 dodge stratus to get at the water pump?


Dear Stratus,
In order to remove the crankshaft pulley you need to buy the applications specific crankshaft pulley puller kit from a snap on or matco or mac tool truck.These kits are not found at autozone or checker schucks kragen.After that the removal is a cinch, any more questions get back to me, HOPE I COULD HELP!!!

Nov 23, 2009 | 1998 Dodge Stratus

1 Answer

2001 dodge stratus R/T- serpatine belt fell off- why-


correct sounds like the balance pully fell apart, common problem.the outter ring with grooves to hold belt is held together by rubber,wears out and falls apart,must replace that crank pulley,remove center bolt use a puller to remove pully, then install new one and belt.( must be a puller for newer dodges 1999 and up to work.hope this is helpful.

Oct 04, 2009 | 2001 Dodge Stratus

1 Answer

Need the tool to take the crankshaft off of a 2002 Dodge Stratus


I think you mean the harmonic balancer, which is the pulley mounted at the front of the crankshaft. (You need to remove the engine and all of the pistons to remove the crankshaft itself.) Check your local parts store for a harmonic balancer puller -- I got one from NAPA for about $75 that allowed me to pull the balancer without removing the radiator/condenser.

Jun 12, 2009 | 2002 Dodge Stratus

Not finding what you are looking for?
1995 Dodge Stratus Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...