Question about Mercury Villager

1 Answer

Need 2 no wat type bolts hold on brake calliber on 2001 mercury villager

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 651 Answers

An autoparts store should have these, if not you'll have to get them from a dealer or a junk yard. good luck

Posted on Nov 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What kind of brake fluid is used in 1998 mercury villager?


try checking the cover on the brake fluid resivoir, the recommended type of fluid should be stamped on the cover.

Aug 07, 2011 | 1998 Mercury Villager

1 Answer

How do you get the calliber off of a 1993 toyota corolla


Hi,
I think you mean brake caliper?
1. Jack up vehicle on the side which you want to remove. 2. Remove the wheel. 3. There is 2 main bolts which hold the caliper to the steering knuckle assembly, just unbolt those 2 and the caliper should come away from the rotor etc. 4. Clamp the brake line with a good clamp then undo the hose to the caliper.
This is the pure basics to removing the caliper.
Thanks
Jason

Jan 28, 2011 | 1993 Toyota Corolla

1 Answer

Looking for location of crankshaft position sensor on 2000 mercury villager with 3.3l engine. parts store says there are 2 per vehicle. found one at front of engine. any idea where the 2nd one would be?


The 3.3/3.8L crankshaft sensor is located on the rear of the transmission housing, above the differential housing The bottom of the sensor is positioned next to the drive plate. Remove the 10mm bolt holding the sensor in place and remove the sensor. Install the new crankshaft sensor.
Install crankshaft sensor bolt and tighten. Connect wiring. merry christmas !!

Dec 25, 2010 | 2000 Mercury Villager

1 Answer

The steering pump belt was loose so I tried tightening the tensioner. The belt only got looser.The adjustment bolt seems to be stripped. What can I do to manually tighten it?


you tried to move the adjuster but didnt slacken the supporting bolts first ,sorry you will just have to renew it ,ir slacken the bolts holding the pump and then pull it tight with a crowbar then tighten the bolts again

Dec 17, 2010 | 2001 Mercury Villager

1 Answer

How to replace the speed sensor on a 2000 mercury villager


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Disconnect the VSS electrical connector.
  4. Remove the VSS hold-down bracket bolt and remove the bracket.
  5. Remove the VSS from the vehicle.
  6. The installation is the reverse of removal. When installing the VSS hold-down bracket, tighten the bolt to 44–61 inch lbs. (5–7 Nm).


8ef1d6d.gif
Vehicle speed sensor location

Sep 13, 2010 | 2000 Mercury Villager

1 Answer

How to remove stripped bolts on mercury villager 2000 front brake caliper


if you mean the slides, try cutting off about half of the boot that covers the bolt head; then you will have enough of the bolt head exposed so you can clamp on a set of vice clamps. Then get new bolts and make sure you use the correct bolt remover. Sometimes when one gets stripped, the mechanic will replace it with a different type head pattern from the other bolts on your calipers.

Aug 16, 2010 | 2000 Mercury Villager

2 Answers

Need a key for a 2001 mercury villager where can i find one


YOU HAVE TO GO TO THE MERCURY DEALERSHIP.SINCE YOUR VECHICLE HAS THEFT SECURITY SYSTEM. THEY HAVE TO SPECIAL MAKE KEYS BEFORE KEY SWITCH AND IGNITION IMMOBILIZER MODULE WILL WORK ALLOWING VECHICLE TO CRANK.

Jul 25, 2010 | 2001 Mercury Villager

1 Answer

Fix speedometer on 93 mercury villager


remove the 2 pin connector from the vehicle speed sensor on the top rear of th trans. clean terminals, see if fixed. If still bad, nylon gear on speed sensor is bad. 10 mm bolt holds it in but most are corroded in place and impossible to remove. Only twist & pry on metal base.

http://groups.yahoo.com/group/villagerquest/

Apr 25, 2010 | 1995 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...