Question about 2004 Toyota ECHO

1 Answer

I cannot re-install the rear axle shaft on a !((# toyota four runner Sr5 as the shaft will not fully enter the differential.Do i need to open the differential to get a better look at the problem.Any advice.

Posted by on

  • 4 more comments 
  • cairlinn Nov 29, 2008

    i removed the axle shaft to replace the wheel bearing. I cannot push the axle shaft all the way inas it appears not to want to engage diferntial.

  • cairlinn Nov 29, 2008

    the shaft is about an inch away from the .I cannot even get the studs to align The bearings and seals are in correctly.I can feel the axle moving when I rotate the drive shaft.It appears the spider gear will not allow the splined end of the shaft to completely enter the spider.

  • cairlinn Nov 30, 2008

    would opening the diferrential cover allow me to align the spider or see what the problem is?

  • cairlinn Nov 30, 2008

    many thanks for all the help. I haven't drained any fluid as it had been leaking previuosly which is what brought me to changing the real bearings on one side only.

  • good wrench May 11, 2010

    How far does it not go in.There isn't anything in the diff to stop it,it just slides in the spider gear.You might of put the bearing on backwards look at the old one and see if there is any difference to either side i recall seeing some bearings that have the inner race of the bearing protrude on one side.Also make sure that the last spacer that you put after the abs ring isn't on too far as it will not contact the seal and your fluid will leak out.

  • good wrench May 11, 2010

    why did you remove the axle

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Ok one inch is a lot.I'm thinking damaged spline or bent axle,not sure on how you removed the old bearing,Did you do both sides and mix up the axles and put the left on the right and the right on the left.Try to put the axle in to the point to where the axle just starts to spin with the drive shaft and see how much further it goes in.Maybe you have a bad carrier bearing causing the carrier to be slightly out of alignment.I have seen a few chevy trucks with limited slip differential that the axle had to be tapped in with a hammer (very soft hit).Should slide right in though.I don't know what else to tell you it is pretty straight foward.Did you drain the fluid out of the rear and was it clean or any chunks on the drainplug magnet.Let me know what happened and if you need any more help

Posted on Nov 30, 2008

  • good wrench Nov 30, 2008

    The rear uses what some call a pumpkin unit which means that everything is one unit.So removing it will let you take everything ont in one piece with out changing any backlash or bearing preload settings.You then can put the axle in and see how it fits and check for damage.It takes some time but if that is what you need to do to rule out what it is then i would check it.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear axel wheel bearing and seal on 2006 jeep liberty renegade 4wd


its not just the seal.... i bet,

99% of seals that fail are , the bearing is allowing , out of spec.

moving in the axle

so when doing all that hard work ? we check this first.

do you know all cars have this book, called the FSM.

and all show you how this is done? every one.

factory service, manual,



but hark, we have them on line now.

alldata.com (15 BUCKS)



I BET PART 2 AND 3 ARE BAD HERE

http://www.factorychryslerparts.com/showAssembly.aspx?ukey_assembly=533119&ukey_product=4240348



THE REAL CD IS ABOUT $130 (instant payback first job done by you) see?



https://www.techauthority.com/en-US/Pages/Home.aspx





eg.

Removal & Installation


  1. Before servicing the vehicle, refer to the Precautions section.


  2. With vehicle in neutral, position vehicle on hoist.


  3. Remove differential housing cover and drain lubricant.


  4. Rotate differential case so pinion mate shaft lock screw is accessible. Remove lock screw and pinion mate shaft from differential case.


  5. Push axle shaft inward and remove axle shaft C-lock from the axle shaft.


  6. Remove axle shaft from side gear and axle tube.


  7. Remove axle shaft seal from axle tube with a seal pick.


To install:



  1. Remove any old sealer/burrs from axle tube.


  2. Coat new seal lip with axle lubricant and install seal with a seal driver.


  3. Lubricate bearing bore and seal lip with gear lubricant.


  4. Install axle shaft through seal, bearing and engage into side gear splines.


  5. Install C-lock in axle shaft end, then push axle shaft outward to seat C-lock in side gear.


  6. Install pinion mate shaft into differential case and through thrust washers and differential pinions.


  7. Align hole in shaft with hole in the differential case and install lock screw with Loctite on the threads. Tighten lock screw to 8 ft. lbs. (11 Nm).


  8. Install the differential cover.


  9. Install rear brake components.

Sep 06, 2014 | 2006 Jeep Liberty Renegade

1 Answer

1998 ford explorer 2 wheel drive rear wheel bearing replacement


what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) swn~us~en~file=st1514a.gif~gen~ref.gif Axle Seal Replacer
T83T-1175-A swn~us~en~file=st1283a.gif~gen~ref.gif Axle Wheel Bearing Puller
T83T-1225-A swn~us~en~file=st1322a.gif~gen~ref.gif Axle Wheel Bearing Replacer
T83T-1225-B swn~us~en~file=st1326a.gif~gen~ref.gif Driver Handle
T80T-4000-W swn~us~en~file=st1185a.gif~gen~ref.gif Impact Slide Hammer
T50T-100-A
Removal
  1. Remove the axle shaft; refer to Axle Shaft in this section.
Axle Shaft Removal
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
    Loosen the lug nuts (1012).
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the wheel and tire assembly.
  1. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
  1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Remove the U-washers (4N237).
    1. Push the axle shafts inboard.
    1. Remove the U-washers.
  1. Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal (1177).
    Remove the two axle shafts.
Installation
  1. Lubricate the lip of the inner wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal.
    Install the two axle shafts.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
  1. Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
    1. Install the differential pinion shaft lock bolt.
  1. Install the rear disc brake rotors; refer to Section 206-04 .
  1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
    Clean the wheel hub and mounting surfaces.
  1. Install the tire and wheel assembly.
    1. Position the tire and wheel assembly.
    1. Install the lug nuts and lower the vehicle.
    1. Tighten the lug nuts.
    1. Install the center cap.


  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
    NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
    Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.
Installation
  1. Lubricate the new rear wheel bearing.
    1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.
  1. Lubricate the lip of the new axle shaft oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.
  1. Install the axle shaft; refer to Axle Shaft in this section.

May 18, 2011 | Ford Explorer Cars & Trucks

1 Answer

1989 toyota 4x4 pickup 3.0l truck will shift in 4high or low ,i jacked the rear end up put the truck in 4 wheel high, tne transfer case shaft is turning to the front differential but the front shafts or...


you probably have a problem with the differential in the front it might be no good it looks like a rear end pull the cover off and check the gears

Aug 21, 2010 | 1989 Toyota Pickup SR5

2 Answers

How to remove rear axle?


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the differential housing cover and drain the lubricant.
  4. Remove the rear brake drums.
  1. Remove the differential pinion shaft.
1
Remove and discard the differential pinion shaft lock bolt.
2
Remove the differential pinion shaft.
  1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves.
Remove the U-washers.
1
Push the axle shafts.
2
Remove the U-washers.
  1. CAUTION: Do not damage the inner wheel bearing oil seal.
Remove the two axle shafts.

Installation

  1. Lubricate the lip of the inner wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. CAUTION: Do not damage the inner wheel bearing oil seal.
Install the two axle shafts.
  1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves

Apr 08, 2010 | 1999 Ford Econoline

1 Answer

How to remove gears from differential on a 95 mustang v6


Removal
  1. Raise vehicle and place jackstands under rear frame crossmember. Lower the hoist so that rear axle housing is at suitable working height.
  1. Remove axle housing cover from rear axle housing and drain lubricant.
  1. Perform the inspection before disassembly.
  1. Remove rear wheels, rear disc brake calipers and rear disc brake rotors.
  2. Working through cover opening, remove differential pinion shaft lock pin and remove differential pinion shaft and differential pinion gears (4215). 3fdbe2c.gif
NOTE: THIS IS FREE INFORMATION!!!!
  1. Remove rear brake anti-lock sensor . Push axle shaft inward until u-washers at button end of the axle shaft are clear of side gear recess.
  1. stb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage inner wheel bearing oil seals when removing axle shafts from rear axle housing. In addition, axle shafts should be completely removed from rear axle housing.
    Remove u-washers and pull axle shafts out of the rear axle housing. 85189ce.gif

Mar 25, 2010 | 1996 Ford Mustang

1 Answer

How do you change a wheel seal on a mercury mountaneer 1998 rear end


Axle Vent
NOTE: If the vent cannot be cleared, it must be installed new.
A plugged vent will cause excessive seal lip wear due to internal pressure buildup. If a leak occurs, check the vent. Make sure the vent hose is not kinked. Remove the hose from the vent nipple and clear the hose of any foreign material. While the hose is removed, pass a length of mechanics wire or a small diameter Allen wrench in and out of the vent to clean it. Connect the hose when done. The vent is located on the drivers side top of axle housing.
If you plan on doing most repairs yourself I would suggest buying a Haynes or Chilton manual for your particular vehicle. Or there are some data disks on e.bay($12-$15) For a cost of under $25, you can almost do any repair yourself with these manuals.Also there are online manuals like the site called ALLDATA where guides can be viewed for a fee. All these solutions will save you time and money, and give peace of mind over correct repairs. I can post you some procedures here also.
  1. CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
  2. Loosen the lug nuts (1012).
  3. Remove the center cap.
  4. With the weight of the vehicle on the wheels, loosen the lug nuts Raise and support the vehicle. .Remove the wheel and tire assembly.
  5. Remove the lug nuts.
  6. Remove the wheel and tire assembly. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
    2. a167554.gif
7.Remove the rear disc brake rotors You will have to remove the brake caliper to get rotor off.
8. CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
9.
1.Remove the differential pinion shaft lock bolt. 2.Remove the differential pinion shaft. 4fd1df0.gif 10.CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Remove the U-washers (4N237).
  1. Push the axle shafts inboard.
  2. Remove the U-washers.
  3. 9499075.gif
    11.Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
    2. 91fc782.gif
      12.CAUTION: Do not damage the inner wheel bearing oil seal (1177). Remove the two axle shafts. 1848771.gif
CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time. NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris. Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.

0ffed5b.gifAxle bearing puller end..
Installation
Lubricate the lip of the inner wheel bearing oil seal.
Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
  2. Remove the differential pinion shaft.
  3. Remove the differential pinion shaft lock bolt.
  4. Remove the differential pinion shaft.
  5. 5a472e0.gif
    CAUTION: Do not damage the inner wheel bearing oil seal. Install the two axle shafts. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
    2. 345272a.gif
      Install the differential pinion shaft.
      1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
      1. Install the differential pinion shaft lock bolt.
      2. 49e064a.gif
                                                            Install the rear disc brake rotors; Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant
                                                            WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control. Clean the wheel hub and mounting surfaces. Install the tire and wheel assembly.
                                                            Position the tire and wheel assembly. Install the lug nuts and lower the vehicle. Tighten the lug nuts. Install the center cap. 6a78fd6.gif WHEW Hope this can help you

                                                            Mar 21, 2010 | 1998 Mercury Mountaineer

                                                            2 Answers

                                                            Rear axle leaking


                                                            Block the front tires. Break the rear lugs loose. Jack up the rear of the truck at the center if possible. remove the wheels & brake drums. Remove the brake shoes,return springs & all the other hardware. Remove the differential cover & drain oil. If you have a posi the next step sucks. You need to remove the threaded pin from the housing & remove the axle retaining clips. All the while,being carefull of the spring in the posi unit. If no posi,then same procedure,minus the "pucker factor". After the axle is out,take a large flat blade screw driver or pry bar & pop the seal out. Keep in mind the axle bearing is probably gone too , so that's another procedure. Keep it apart,you'll be glad you did.

                                                            Jun 23, 2009 | 2004 Ford F150

                                                            1 Answer

                                                            How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


                                                            Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
                                                            Removal
                                                            sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
                                                            1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




                                                            1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
                                                            1. Drain rear axle lubricant by removing the axle housing cover .
                                                            1. Remove differential pinion shaft lock pin and differential pinion shaft .


                                                              9979cb3.gif
                                                            1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



                                                            1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
                                                            Installation
                                                            NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
                                                            sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
                                                            1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
                                                            1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
                                                            1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




                                                              NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
                                                              sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
                                                            1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



                                                            1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
                                                            1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
                                                            1. Install rear disc brake caliper and rear disc brake rotor .
                                                            1. Install wheels and tires.
                                                            ---------------------------------------------------------
                                                            1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

                                                              Rear Disc Brake Caliper Anchor Plate




                                                            1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



                                                            1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



                                                              sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
                                                            1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



                                                            1. Install axle shafts as outlined.

                                                            May 13, 2009 | 2004 Ford Crown Victoria

                                                            2 Answers

                                                            Rear wheel bearing


                                                            SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal
                                                            1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
                                                            1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
                                                            1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
                                                            1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
                                                            1. Remove the differential pinion shaft (4211).
                                                              1. Remove the differential pinion shaft lock bolt (4241).
                                                              1. Remove the differential pinion shaft.
                                                            1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
                                                              Remove the U-washer (4N237).
                                                              1. Push the axle shafts (4234) inboard.
                                                              1. Remove the U-washer.
                                                            1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
                                                              Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
                                                            1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
                                                              Remove the axle shaft.
                                                            --------------------------------------------------------------------------------------
                                                            Rear Wheel Bearing and Axle Shaft Oil Seal Removal
                                                            1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
                                                            1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
                                                              Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
                                                            Installation
                                                            1. Lubricate the new rear wheel bearing with the specified lubricant.
                                                            1. Using the special tools, install the new rear wheel bearing.
                                                            1. Lubricate the lip of the new wheel bearing oil seal.
                                                              • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
                                                            1. Using the special tools, install the new wheel bearing oil seal.
                                                            1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

                                                            -------------------------------------------------------------------
                                                            Installation
                                                            1. Lubricate the lip of the wheel bearing oil seal
                                                              • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
                                                            1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
                                                              Install the two axle shafts.
                                                            1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
                                                              Install the U-washer.
                                                              1. Position the two U-washers on the button end of the axle shaft.
                                                              1. Pull the axle shaft outward.
                                                            1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
                                                              Install the differential pinion shaft.
                                                              1. Align the hole in the differential pinion shaft with the case lock bolt hole.
                                                              1. Install a new differential pinion shaft lock bolt.
                                                            1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
                                                            1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
                                                            1. Install the rear brakes. For additional information, refer to Section 206-04 .
                                                            1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
                                                            1. Lower the vehicle.

                                                            Apr 10, 2009 | 2004 Ford GT

                                                            1 Answer

                                                            Replace left rear axle seal 1999 ford explorer


                                                            Axle Shaft Removal
                                                            1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
                                                            1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
                                                            1. Remove the differential housing cover (4033).
                                                              1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
                                                              1. Remove the bolts.
                                                              1. Remove the differential housing cover.
                                                            Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
                                                            1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
                                                              Remove the differential pinion shaft.
                                                              1. Remove the differential pinion shaft lock bolt.
                                                              1. Remove the differential pinion shaft.
                                                            2. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the U-washer groove.
                                                            3. Remove the U-washer (4N237).
                                                            4. Push the axle shaft inboard.
                                                            5. Remove the U-washer.
                                                            Reinstall the differential pinion shaft.
                                                            1. Install the differential pinion shaft.
                                                            2. Install the differential pinion shaft lock bolt finger-tight.
                                                            3. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal (1177).
                                                              Remove the axle shaft.
                                                            -----------------------------------------------------------------------------------------------------------------
                                                            Seal Removal
                                                            1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.
                                                            1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
                                                              NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
                                                              Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.
                                                            6c7eb46.gif Installation
                                                            1. Lubricate the new rear wheel bearing.
                                                              • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
                                                              • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
                                                            1. Using the special tools, install the rear wheel bearing.

                                                            ece7d89.gif
                                                            1. Lubricate the lip of the new wheel bearing oil seal.
                                                              • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
                                                            1. Using the special tools, install the wheel bearing oil seal.
                                                            c21e27d.gif
                                                            1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

                                                            Feb 22, 2009 | 1999 Isuzu Rodeo

                                                            Not finding what you are looking for?
                                                            2004 Toyota ECHO Logo

                                                            282 people viewed this question

                                                            Ask a Question

                                                            Usually answered in minutes!

                                                            Top Toyota Experts

                                                            yadayada
                                                            yadayada

                                                            Level 3 Expert

                                                            63661 Answers

                                                            Colin Stickland
                                                            Colin Stickland

                                                            Level 3 Expert

                                                            21981 Answers

                                                            Jeff Turcotte
                                                            Jeff Turcotte

                                                            Level 3 Expert

                                                            6812 Answers

                                                            Are you a Toyota Expert? Answer questions, earn points and help others

                                                            Answer questions

                                                            Manuals & User Guides

                                                            Loading...