Question about 2003 Saturn VUE

1 Answer

Crankshaft position sensor

I have a code error 0335 and i need to locate the crankcase position sensor

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 204 Answers

Usually, the crank sensor sits on the bottom of the engine and usually on the drivers side. Some other places it might be is on the passeger side at the bottom and also on the transmission bellhousing near the bottom on either side. Hope this gives you some direction. Thanks for Using FixYa!

Sincerely,

JC

Posted on Nov 28, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 ssangyong rexton, it cuts out when hot? theres a few fault codes come up, p1677, po675, po335 po372, any help would be much appreciated...


1677 may be Drive by Wire - MIL Circ. Short to B + Ssanyon is not listed as they use OEM parts.
0675 Cylinder 5 Glow Plug Circuit/Open
0335 Crankshaft position (CKP) sensor - circuit malfunction
0372 Timing reference, high resolution signal A - too few pulses

Jun 26, 2017 | SsangYong Cars & Trucks

1 Answer

2000 odyssey CKP problem code P0335. I replace the crank seal and this code show up after that. then I open again to replace the sensor and code still there. What I can do? thanks


code p 0335 refers to crankshaft position sensor (CKP)---circuit malfunction===causes ---wiring---CKP sensor ---ECM
the wires are a good place to start and check for damaged insulation , broken wires or bad harness connections
next there is an air gap setting between the sensor and the exciter (segmented bars on a ring) on the crankshaft check that is correct ---dimension available from the workshop manual

Oct 06, 2016 | 2000 Honda Odyssey

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

2 Answers

Have a 2004 kia sedona have replaced the crank position sensor but still shuts off and gives p 0335 code


WHAT CKP SENSOR DID YOU REPLACE I BELIEVE THE SEDONA 3.5L ENGINES HAS 2 CKP SENSORS.YOU HAVE ONE CKP SENSOR LOCATED FRONT OF ENGINE ON THE OIL PAN MOUNTED BEHIND CRANKSHAFT PULLEY AND THE OTHER CKP SENSOR LOCATED NEAR THE TRANSMISSION BELLHOUSING. CHECK TO SEE IF YOU HAVE CKP SENSORS. IF NOT CKP SENSOR WIRE COULD BE DAMAGED.ALSO CHECK TO MAKE SURE BATTERY POWER GOING TO CKP SENSOR B PLUS WIRE IF NOT CHECK THE ECCS RELAY OR FUSES MAKE SURE POWER IS GOING TO CKP POSITION SENSOR

Oct 10, 2011 | 2004 Kia Sedona

1 Answer

What is repair code 0335 please


That code is for a Crankshaft position sensor. It is a common failure for dodge/chryslers.

Jan 11, 2011 | 2005 Dodge Ram 2500 Truck

1 Answer

Where is the location of the crankshaft position sensors on a 97 Cadillac Deville. It stalls at red lights and stop signs and I've heard a new crankshaft position sensor is a possible solution. I've got...


The check engine light doesn't have to come on with a bad crank sensor ,your vehicle has two , one for lower rpm an one for higher speeds . A&B
The two crankshaft sensors are located on the front bank (BANK 2) of the engine block between cylinders 4 and 6. Crankshaft position A sensor is located in the upper crankcase and crankshaft position B sensor is located in the lower crankcase. Both sensors extend into the crankcase and are sealed to the engine block with O-rings. The crankshaft position sensors are not adjustable.

Nov 18, 2017 | 1997 Cadillac DeVille

1 Answer

WHERE IS THE CRANK SHAFT SENCER LOCATED ON THE MOTOR


The 2 crankshaft sensors are located on the front of the engine block, between cylinder Numbers 4 and 6. Crankshaft position A sensor is located on the upper crankcase and crankshaft position B sensor is located in the lower crankcase. Both sensors extend into the crankcase and are sealed into the engine block with O-rings. The crankshaft position sensors are not adjustable.

Jun 08, 2010 | 1998 Cadillac Catera

1 Answer

0335 fault code what is it


Your crankshaft position sensor circuit has a fault.

Oct 15, 2009 | 2004 Nissan Sentra

2 Answers

Crankshaft Position Sensor Error P0335 recurred after r&r


In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Jul 25, 2009 | 2003 Nissan Altima

2 Answers

Crankshaft sensor location and replacement procedure


It is on the rear of the engine, passenger side. You need to access it from the underside and it is halfway up the block between the head and the oilpan. It is real close to where the engine and transmission meet.

May 23, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
2003 Saturn VUE Logo

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8825 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...