Question about 2000 Hyundai Accent

1 Answer

I want to remove the 100amp fusible link on my 2000 Accent. Does it just pull out upward or do i have to loosen the bolts on the side? i cannot tell if the bolts hold in the link or the fuse box itself. Will the local auto part store be able to tell if it is blown? I am a Grandma with some auto knowledge but cant figure this one out! thanks for any help!!! PS removing this cause car wont start even tho it cranks-have gas and accessories turn on

Posted by on

  • 2 more comments 
  • pftryon02 Nov 28, 2008

    thanks silver top. i will try the fuel shut off switch. Son in law thinks there is no spark but he used brass coated nail in spark plug to test, ? questionable move there!! Car was running fine two days ago. bought new battery 08/08. any chance of timing belt problem? that was replaced at about 70k miles 92 k miles now been running fine

    o2 sensors replaced 1 yr ago.are there other fuses i might check? This is very much a cost issue as i cant afford any bill esp from mechanic or dealership.car is still under powertrain warranty.

  • pftryon02 Nov 30, 2008

    SilverTop, checked fuses marked ignition and battery- they are good. Not in location you said but looked at the schematic on top of the relay box under hood to see locations.Will try disconnect of battery cable tomorrow to see if it resets immobiliser chip(don't think 2000 Accent has this as it doesnt seem to be mentioned in troubleshooting pages for hyundai)- also +pole is corroded but i have power in interior so dont think battery is true problem. Thanks, Pat

  • silver top May 11, 2010

    hi thanks for update if you have no spark? it may be ign fuse ecu2 10amp red on inner panel above bonnet release fuse 1/2 way down 2nd column i think but check em all? also the hyundai's have immobiliser which is a chip in the ign key do you have a master key with the car? normally provided when bought new ? if so it is normally blue?as my wifes is?for her getz and her prev car was the accent try this? if you disconnect battery wait 10 mins then reconnect immob may reset on ecu? for your info apparently some accents do have immob problems and some where on this board? there is someone who had this problem and solved it diy! last week it does sound like the immob is acting up and preventing ign to plugs? however have never had such trouble with wifes hyundais re immobs but i will make enquires about reseting and get back to you asap if i find out pretty sure it involves key in ign and pressing the trip meter button on speedo in a sequence ?

  • silver top May 11, 2010

    hi from uk do not remove the fusible 100amp link this for battery power and it is ok as your engine turns over ? have you checked the fuel shut off switch in engine compartment? it is at rear of engine attached to bulk head just press the red?rubbercap down ? also any spark at plugs? if you could provide more info on history prior and after this fault?? occured it would help to offer advise on what may be the problem best wishes

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 12,104 Answers

If blown vehicle wont crank over and would have no lights no nothing

Posted on Jun 16, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2001 accent how to remove the window handle

push and move it to the front

Posted on Jun 24, 2008

keemo68
  • 1263 Answers

SOURCE: 2000 2 door accent removed

you have to reset the ecm code , when you removed the fuse the ecm registered this as a loss of voltage and threw a code so now it doesn't know that the fuse has been replaced. you need a scan tool to reset the ecm...please rate the solution...thanks

Posted on Sep 22, 2008

motor1258
  • 6674 Answers

SOURCE: Removing window crank

Push in on door panel as suggested & you may have to spin handle or tool, then feel it slide in to right spot (slot cut) & push tool & handle should release

Posted on Apr 11, 2009

  • 490 Answers

SOURCE: Removing door panel on 1997 Hyundai Accent

Look under the round part of the handle,see if there is a small allen screw there,if it is unscrew it until the handle comes off.if not send a new message

Posted on Sep 06, 2009

  • 9 Answers

SOURCE: Trying to change the timing belt on a 2003 Hyundai

you can put a breaker bar and socket on the bolt and unplug a) the injectors or b) the coils so it wont start and crank it over like 2 times put the breaker bar on the pulley with the handle of the breaker bar touching the ground and u crank it and it'll break free

Posted on Oct 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ALTERNATOR BELT INSTALATION 1996 ACCENT


Loosen Alternator Support Bolt. Loosen Alternator Lock Bolt. slide alternator to loosen tension on belt. Remove belt. Reverse procedure to install.

12_20_2011_1_36_18_am.gif

Dec 19, 2011 | Cars & Trucks

1 Answer

Hi, I was wondering how I get the speaker covers off of my 2000 hyundai accent...4 door sedan? There in the back and there seems to be no way of taking them off without breaking them. Also, do i need...


You have to remove the rear dash board. the covers don't come off. Remove the bottom seat first, then there will be 2 bolts to remove the back rest. Then you can access the speakers. To remove the bottom usually push it back and pull up where you sit you ****, on both sides.

Apr 21, 2011 | 2000 Hyundai Accent

1 Answer

Trying to remove the 100amp alt fuse in 1994 camry as it has blown what do i have to do


Remove the lower cover from the fuse box, turn it side ways then remove the 2( 8mm ) bolt that hold the fuse.If you already broke the fuse legs grab them with pliers remove the bolts and then pull them out.

Dec 23, 2010 | 1994 Toyota Camry

1 Answer

How to take the alternator off?


I did this recently on Hyundai Accent. First things first is to disconnect the battery to prevent any contact that can produce sparks during the disconnection of the positive (+) supply of the alternator 1. Jack up car. Remove splash guards from bottom. 2. From bottom loosen pivot bolt. 3. From bottom disconnect cables. 4. From top loosen adjustment bolt and slacken belt. 5. Remove belt from pulley and remove adjustment bolt. 6. From bottom remove pivot bolt. 7. Alternator may have corroded to mounting bracket so work it loose. 8. Find out alternator will not slide out of engine compartment. 9. Loosen radiator mounting bolts. 10. Shift radiator to side to make more room to get alternator out. 11. Install alternator. 12. Put radiator back in its place.
I guess it depends on what year... I too just did an alternator on a 2001 Accent. First, and what the previous forgot, disconnect the negative battery cable. Steps 1 thru 5 are exact. Step 6 is where we differ. 6. From bottom, push alternator up and out of mounting slot, gently work it down and out. 7. The pivot bolt can then be punched out (my bolt had a center mark where a punch would stay, so not to damage the threads) and then put into the replacement. Re-assemble in reverse order.
Last night I did this repair on 1999 accent. a 10mm and 12mm sockets and end wrenches are needed. After trying to wiggle the alternator up through the top, I was afraid of damaging other electrical connections, so I took the oil filter off. It was time for an oil change anyway, but just removing the filter only lost maybe half a quart of oil. The local autozone had an alternator for 129.99, lifetime warranty.


Dec 22, 2010 | 2000 Hyundai Accent

1 Answer

How do I remove the engine cover on a 2008 acadia to access the power steering reservoir?


Hi, viewer! Remove first the engine oil cover (yellow?) turn it conterclockwise to loosen out. Then pull the cover upwards from side to side. There are no bolts, just pull carefully upwards with enough force to get past the retaining clips underneath the cover. Was that okay? I hope you be alright, goodluck! : )

Sep 18, 2010 | 2008 GMC Acadia

1 Answer

I need the fuse box diagram for a 2004 325xi bmw


2004 BMW 325XI AWD 2.5L EFI DOHC 6cyl

Fusible links are often identified by the color coding of the insulation. Refer to the accompanying illustration for wire link size and color.

23a1113.jpg

Fig. Common fusible link color coding

Circuit Breakers - Resetting & Replacement
Circuit breakers are located inside the fuse panel. They are automatically reset when the problem corrects itself, is repaired, or the circuit cools down to allow operation again.

Fuses Replacement
Use the provided plastic fuse puller located in the fuse panel to remove fuses. The upper lid of the fuse panel has a diagram of the fuse locations and amperage ratings for each circuit. The fuse is removed by simply pulling upward on the fuse with the removal tool.

The fuses are easily checked by visual inspection. With the ignition switch OFF pull the fuse out of the holder. Check the fuse filament. It should be continuous and not broken. If the filament is broken, replace the fuse with one of the same amperage rating.


The fuse and relay box on the E30 and E36 models is located in the engine compartment. The E36 models also has relay boxes located under the left side of the dashboard.

The diagram is in section 610 of the Bentley Manual. Some have downloaded it through a link provided here: http://www.bimmerwerkz.com/forum/3-s...4-a-50762.html

Good luck.

Sep 25, 2009 | 2000 BMW 3 Series

1 Answer

How to change the air filter of hundai accent


dear friend-the top section of the airbox is held inplace by spring clips,unclip and pull the top cover upwards,remove air filter,check for dirt inside and clean out,fit new filter and close up.

Jul 29, 2009 | 2000 Hyundai Accent

1 Answer

Just want to replace the belt do i have to remove the alternator


Back in 2000 Hyundai did not use automatic tensioners on the 2000 accent. You have to loosen the bolt on the side of the tensioner. Then you turn the other bolt counter clockwise to loosen the bolt which will loosen the tensioner. Then you have to loosen the big bolt that is on the other side of the alternator. You may have to take off your power steering belt to get to the alternator belt. Now do the opposite to install your belt.
I hope this helps.

Apr 07, 2009 | 2000 Hyundai Accent

1 Answer

92 toyota paseo alternator not charging


you may have missed a fuse or fusible link , there is a 100amp alternator fuse and a 50 amp fuse on that circuit , location of those 2 fuses are (left side of engine compartment) also there is a fusible link in that circuit right off the positive side of the battery , those big fuses don't look anything like a normal if that helps , cheers'

Jan 13, 2009 | 1992 Toyota Paseo

Not finding what you are looking for?
2000 Hyundai Accent Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...