Question about 2005 Saturn SW2

1 Answer

Rusted bolts I have to replace the drivers seat in my 1995 saturn sw2, the factory bolts are rusted to pieces, hoping to find out the bolt specs so i can have some made as there is only one dealership in canada that still carries them and they'll take 4-6 weeks to get here! please help! thx

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 651 Answers

Have you checked autoparts stores? they should be able to get you what you need.

Posted on Nov 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Caliper bolts get loose


the main mounting bolts? not guides?
caliper mount to knuckle bolts?
what torque did you use? in foot/lbs.

  1. id bet they are not factory spec bolts
  2. or you used the wrong torque page.
  3. or your tool is no good. (harbor fright tools?)
use a beam torque tool, it will never fib to you, like cheap clickers do.
I promise.
specs
tighten the caliper pin bolts to 26 ft. lbs. (36 Nm). Bottom bolt
there are 4 bolts specs here.
above pin
banjo 17ft/lbs
top B bolts is 61.5 foot lbs. (this came loose at 61 ?)
C spec is 5ft/lbs on bleeder nipples.

now alternator tack.
the rotor is warped so bad it bead the calipers to death.
the wheel bearing, is so bad , same.

ever check those for run out, and end play?
bingo if true.
damage and collateral damage are limitless.
and rust too. (entropy of all kinds)

Apr 16, 2014 | 2010 Suzuki Grand Vitara

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Don't know where fuel filter is -95 ram 3500


Mine was located on the driver side rail, on the drivers side of the transmission near the middle of the drivers seat. It was BOLTED to the rail and was very rusted. I think it took two hours for penetrating oil to loosen it up

hope this helps

Jim

Nov 27, 2012 | 1995 Dodge Ram 3500

1 Answer

Installing radiator in 2000 saturn sw2


remove the air filter box then the fan cartridge then from under the car remove the splash shield to get to the a/c condenser bolts you can let the condenser hang slightly drain the radiator then remove the hoses reverse procedure to install

Jul 30, 2012 | 2000 Saturn SW2

1 Answer

Looking for head bolt torque for 95 SOC saturn. im having valve guides replaced


The torque spec are as follows, step one is 22 ftlbs then step 2 is 33ftlbs and the third step is to tighten bolts 90degrees more also the bolt tightening sequence is here, this is a diagram of the bolts good luck and i hope this helps.johnjohn2_60.gif

Jan 10, 2011 | 1995 Saturn Sl

1 Answer

Will a front seat from a 1993 Saturn fit in a 1995 Saturn SC1


the SL seats were pretty interchangeable, so i would imagine the SC seats are as well. there are only 4 bolts so it does not take long to check/

Sep 19, 2010 | 1995 Saturn Sl

1 Answer

New Drivers side Rear strut on 94 Saturn SW2 Tire now Rubs strut?


most likely the knuckle is also bent near where the strut bolts to the knuckle

Apr 06, 2009 | 1993 Saturn SW2

1 Answer

Cant find gas door release on saturn sw2 96. Where is it


release lever left of driver seat near rear hatch release on floor

Mar 28, 2009 | 1996 Saturn SW

1 Answer

New seats


real easy there are 4 bolts in the seat 14 or 15mm just take the bolts and lift out throught the door/ Please rate my response thank you very much

Jan 31, 2009 | 1995 Saturn Sl

1 Answer

I need to replace the front driver's seat in a 95 saturn...


seat frame base is held to floor with four bolts, one in each corner.  Begin by moving seat to the full forward position, remove the two rear seat frame bolts, they may be covered by carpet and plastic trim.  Them move seat to full rear position and remove both front frame bolts, the seat will now be free to remove.  Keep me posted

Jan 06, 2009 | 1995 Saturn Sl

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...