Question about 1990 Chevrolet Corvette

2 Answers

1990 corvette engine light came on and engine died and won't star

The engine will turn over but won't start done all that i know to do but still won't start

Posted by on

  • HippyRoy Beasley Nov 30, 2008

    security light normal. peplaced cap, rotor, module,coil, and filter. fuel pump working normal. but thanks

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I don't know if I have the solution, but check your injectors. My 90 Vette died on the highway, I thought fuel pump right away, that wasn't it. After I went through my punch list I took it in....an injector was fouling up the computer. The mechanic disconnected it and it ran.

Posted on May 09, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 99 Answers

Is it a security light that comes on? if so you may have a problem with the ign system. can you hear the fuel pump come on when the key is turned on?

Posted on Nov 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the head lights on a 1989 Chevy corvette ?


1st I'll need to know what the problem is with them exactly, won't flip up, headlight bulbs are not turning on but light carriages do flip into the up position?? What? What work have you done if any to try and repair whatever this problem is with the headlights? Throw me a bone here, I own a 1996 C4 now and have rebuilt another (84) from a rolling wreak. I know thwe problems wit the lights.

May 21, 2012 | 1989 Chevrolet Corvette

1 Answer

HOW DO I RESTET CHANGE OIL LIGHT ON 1990 CORVETTE


Corvette 1990-1996

After an oil change, or when "CHANGE OIL" appears on the Trip Monitor, with the ignition on and engine off, press the "ENG MET" button (located on trip monitor) once. Press the "ENG MET" button again within 5 seconds. Within 5 seconds, press and hold the "RANGE" button (1990-1994) or "GAUGES" button (1995). The light will flash. When it stops flashing and goes out, the system is reset.

Hope this helps and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using FixYa.

Jose.

Oct 19, 2011 | 1990 Chevrolet Corvette

1 Answer

1990 corvette won't start - we changed all the fuses and had the battery checked for charge - Sears said it was good. What should we try next - we get dash lights, etc. when we turn the key, but...


Gm vehicles have had a ton of problems with the antitheft systems. When will turn the starter off when not functioning properly. http://vatspasslockpasskeysecurityhelp.yolasite.com/

Aug 04, 2011 | 1990 Chevrolet Corvette

1 Answer

1990 Corvette,s fan comes on when the key is turned but car wont start. THANK YOU !


Do the lights come on (dash)? Is the battery up? Is it in park? Try moving the gear selector through the neutral range while holding the key in the start position. If it cranks, the neutral safety switch is out of adjustment or going bad. If the dash lights go out when you hit start, the battery termanals need cleaned (baking soda & hot water & a brush). If the dash lights never come on, do you even have a battery and is it hooked up (including the ground strap between engine and frame)? Ray (garage owner)

Sep 20, 2010 | 1990 Chevrolet Corvette

1 Answer

My 1990 Buick Park Avenue dies after 15 miles


Replace the crank sensor as they get hot they will sometimes quit working. The temp light comes on everytime the engine is turned off and the switch is on. Next time it dies spray or pour some water on the sensor then see if it will crank and if it does you know what it is.

Feb 03, 2010 | 1990 Buick Regal

1 Answer

Twincam engine light comes on and kills motor


the engine starting only when doing a push start sounds like a bad ignition switch. the coil and ignitor are getting power with the ignition switch at "on" but not at the "start" position.

May 19, 2009 | 1990 Toyota Corolla

2 Answers

1990 corvette electrical problems


This may be fuse blow out or may the display is defective in the circuit...........

May 29, 2008 | 1990 Chevrolet Corvette

Not finding what you are looking for?
1990 Chevrolet Corvette Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...