Question about 2002 Mazda B-Series

1 Answer

Timing belt setting and my car iddle are out of form mazda etude

My mazda etude 160 ie 2002 modle is not operating because the timing belt setting are very much incorrect; i need to know how can i fix and put the right time setting and set the idle proper please help me

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

Your camshaft and crankshaft pulleys have to be properly aligned upon installation of the timing belt. The cogs on the belt, should fit precisely with the teeth of the pulleys. Your # 1 engine cylinder should be moved to "Top Dead Center" before installing the belt. This means no compression once the top of the piston cylinder reaches the top of the chamber.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_62314e5b2470e8b5

Posted on Nov 27, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2002 Mazda etude 16 dochrecently I changed the timing belt and serviced the car,but I checked the timing looks fine ,but it can't start,what could be the problem?


If it started fine before, then either the timing is off or somewhere along the line you damaged the crankshaft or camshaft sensor or wiring harness

Dec 04, 2017 | Mazda Cars & Trucks

1 Answer

Hi I have a Mazda etude 1.6 ie I replaced the timing belt and nu it don't wane pick up any revs the timing is correctly set the.valve is ok.it idles well on 2000 revs but when i pres the gas it dies


not a Mazda man but 2000 rpm's at idle is more than double what it should be . My toyota idles at about 750 .runs 2000 going 70 mph down the highway

Jul 30, 2015 | Mazda Cars & Trucks

1 Answer

There is no spark on my mazda etude 160 ie


Check the distributir cap if there is no power there check the coil work backwards away from the plugs till you find power and you have traced that fault.

Jun 11, 2015 | Mazda Cars & Trucks

1 Answer

How do i fix the valve timing seals,and need the timing marks for mazda etude 96 16v doch


Have you replaced the timing belts. If not you need to. To replace the seals you have to remove the gears on the cam shafts.

Mar 04, 2015 | Mazda Cars & Trucks

2 Answers

2002 mazda protege just had timing belt changed, now car is over revving and getting very hot


timing might have adjusted before the belt replacement,so happens. please check the valve and distributor timing once again and in accordance with the new timing belt.your problem will be solved.

Mar 03, 2012 | 2002 Mazda Protege

2 Answers

Mazda Etude 160ie timing


I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Jan 02, 2009 | 2004 Mazda 3

1 Answer

Problem with Altenator belts Etude


the problem is not the altenator. you should have a idler pully and a self adjusting idler tensioner. if thes e go bad the bearings tend to seize up and break belts i would check these first chance you get the tensioner should be spring like and be hard to move back and forth the pulley part of it should spin freely with out makeing a noise. please rate this

Sep 01, 2008 | 1999 Mazda 626

Not finding what you are looking for?
2002 Mazda B-Series Logo

Related Topics:

633 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...