Question about 1990 Nissan 300ZX

1 Answer

Clutch has no pressure and i have replaced everything i know of.

I have a 1993 300zx and my clutch has no pressure it just stays on the floor when i push it down. I have replaced the master and slave cylinder and i dont think it is my pressure plate because it pushes against the slave cylinder nipple. What could be the problem?

Posted by on

  • miko4life Dec 30, 2008

    On my 92 300z, i changed my slave cylinder and master cylinder, i bled the lines, i dont see any air bubbles, nothing........i dont think air is in the lines, BUT i still dont have any pressure!

  • Anonymous Mar 30, 2014

    replace clutch and pressure plate and the clutch pedael is to easy to push fill like there is no pressure

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Did u try bleeding the lines ? if your changed every thing and still have nothing u might just have alot of air in the system

Posted on Dec 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My clutch pedal stay close to the floor in my Acura CL. Doesnt return fully like it used too. Cant figure it out and I've replaced everythin


Bobbie, If your sure the system is bled properly,did you get the clutch fork back in correct position, was it the correct bearing etc., you may have to adjust the clutch pedal and / or if it has a mechanical return spring, change the spring, it could be weak.
Check the attached links,instruction and guides for clutch pedal adjustment., bleeding,etc.Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Clutch Kit Installation Acura CL 2 2L 2 3L

Apr 02, 2016 | Cars & Trucks

1 Answer

New clutch installed. No pedal, stays on floor unless I bring it back up with my hand. No resistance.


`Did it bleed, did fluid come out in a steady stream? Isn't there a spring to bring the pedal off the floor?
Check the linkage of the pedal to rod to the clutch master cylinder, make sure that is all together. Any chance the master has an internal leak and won't build hydraulic pressure down at the slave? If you get it bled, then watch the slave operation while someone works the clutch pedal. The piston on the slave should extend and push the clutch fork enough to disengage the clutch.

Jul 19, 2015 | Nissan Cars & Trucks

1 Answer

Clutch petal stays up with too much pressure car stays in neutral like pedal is pressed to floor


Sounds like an internal clutch/pressure plate issue. Possible broken torsional vibration spring in the clutch assembly keeping clutch engaged. The transmission will have to be removed and clutch inspected/replaced.

Apr 11, 2015 | 2008 Chevrolet Cobalt LT1

1 Answer

Clutch pedal staying down but there's plenty of fluid in resiviour


Probably bad clutch master cylinder and/or slave cylinder. I always replace both.

Oct 04, 2012 | Cars & Trucks

2 Answers

Abnormal clutch pedal operation


You've replaced the master, the slave, now I would check to see if the throwout fork will move by hand. If you can move the fork by hand I would say that your pressure plate and or throwout bearing are worn out. First try to just gravity bleed the system. If that doesnt work, it may be time for a clutch, pressure plate, and bearing. The pressure plate spring pushes the pedal back up and depending on how many miles and driving habit those little arms on it break off and just wear out. I hope this helps you.

Aug 19, 2009 | 1997 Mitsubishi 3000GT

1 Answer

Clutch pedal stays on floor


the problem is that either the master or slave cylinder for the hydraulic clutch have failed, it is always recommended that they both replaced together, u can bleed the clutch but the problem will occur again.

May 07, 2009 | 1994 Mazda MX-6

2 Answers

Clutch has no resistance, stays near floor after applying pressur


You could refill but, i would replace the clutch master cylinder and slave cylinder as well. these two parts are failing.

Mar 06, 2009 | 1991 Honda Accord

1 Answer

Clutch pedle stays down


if you have a hydralic clutch usually the pedal staying on the floor indicates air in the clutch lines. if so check 4 leaks at the filler and at the slave cylinder. however just bleeding the clutch system may temporarily fix your issue

Jan 20, 2009 | 2004 Oldsmobile Alero

1 Answer

2000 cavalier clutch pedle goes to floor when pushed and stays there, clutch not working no pressure


You are going to have to replace the master and slave cylinders for the hydraulic clutch, the seals have failed in the slave, but from past experience they should always been replaced as a pair.

Oct 12, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1990 Nissan 300ZX Logo

591 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...