Question about 2005 Ford Crown Victoria

1 Answer

2005 Crown Vic Police Interceptor: Starts then stalls

I have a 2005 Crown Vic Interceptor with the 4.6L
The car will start then die out suddenly. The fuel pump will run and prime up to pressure. The car will start briefly even if you try to give it throttle.
Any ideas?
It did throw the check engine light, but I have been unable to get it scanned.

Posted by on

  • 3 more comments 
  • Anonymous Mar 13, 2014

    2005 crown vic police int wife was driving then suddly nothing car costed to stop.
    car wants to turn over but no fuel-so replaced fuel filter-still no fuel checked fuses-ok-replaced fuel pump (new harness sending unit the works) car sonds like wants to start but nothing?
    i am at a loss as i also hecked relays as i was told to-still nothing-also cked kill switch in trunk by unpluging and using a jump wire and noting
    please help if possible as we 9family) have no running car

  • Anonymous Mar 13, 2014

    how do i change the airbag in 99 crown vic interceptor

  • Anonymous Mar 13, 2014

    I need to put a airbag in 99 crown vic interceptor

  • Anonymous Mar 23, 2014

    police interceptor. >:)

  • Anonymous Mar 29, 2014

    I put just a cold air filter on my 05 crown vic police interceptor and now it runs rough and check engine light on. it still has sensor on it.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 227 Answers

Have you checked the fuel filter. Fuel pump will pressure up, but fuel filter could be clogged and not work without the pressure of the fuel pump.

Posted on Jan 17, 2009

  • 1 more comment 
  • onman May 04, 2013

    yes i sure have the theives cacked the copper ring around the ignition now she wont talk back

  • onman May 04, 2013

    so will i b able to start my car with the copper ring busted turn my alarm off will that work

  • onman May 04, 2013

    same to me cruzn



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2005 crown Vic police interceptor no communication with pcm and no dash light for ck eng

No idea sounds like a multiplug connection ?? but i have no idea other than this ,now if it was a renault i would know that pluging it in would be a waste of time to start with as its all encrypted software for dealers only but a ford ?? never so look for a broken wiring connector

Feb 25, 2015 | 2005 Ford Crown Victoria

1 Answer

I got a 2000 crown vic. police interceptor an it came with no alternator, got new one and it came with 3 wires and my wiring in the car has 2 wires,whats with the 3'd wire.

They had a couple different alternators for that car,basically the same alternator but different regulators,might be where your trouble lies

Mar 23, 2013 | Ford Crown Victoria Cars & Trucks

1 Answer

2000 crown vic police interceptor bypass a/c clutch pulley

you can get a A/C Delete kit for a Ford 4.6 liter. the 4.6 v-8 accessory drive system is all the same. You may also be able to run a line of string around the pullys, take it to your local auto parts store and they can match it up. I recomend the kit,

Oct 05, 2009 | 2000 Ford Crown Victoria

1 Answer

99 crown vic police interceptor steering wheel??

i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Jul 07, 2009 | 1999 Ford Crown Victoria

1 Answer

Lifter noise

Sludge in the engine.

May 23, 2009 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
2005 Ford Crown Victoria Logo

1,618 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides