Question about 1999 Honda Civic

1 Answer

Ya help - 1999 Honda Civic

Posted by on



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

Next time say more

Posted on Nov 27, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What are the Head Bolt Torque settings for 2004 Vauxhall Corsa 1.2 sxi twinport

Howdie Sure Wood Like to Help Ya But Ya Need to go Down To the DEalers And HAnd them A 20 and Be Nice and they will give ya the Spec,s Can,t Know all of them so best way is the Dealer thank,s again for your time

Apr 25, 2015 | Vauxhall Cars & Trucks

1 Answer

I have 2008 impala 3.9 code 172 alcohol content 78% LT -25 ST -10 HELP

And YA Want What ?Don,t Understand What YA What Me too Say to You ?Sounds Like Fuel Regaltor IS The Problem So far let me Know What Ya Need To finish this thanks for your time

Mar 04, 2015 | 2008 Chevrolet Impala

1 Answer

In the 2002 ford windstar recal for cruise control problems where is the atm fuse and wiring harness located

Under the Hood But Why Do YA Ask This I,m Lost well sounds :like The Column is the Problem or the Servo is acting Up ,What Is It Doin If Ya Mind Me Askin ?Cause it,s goin to cost big Coin Missin with that just to Let Ya Know ther Not Fun Ask Nicely At the Dealer for Imput on It ASk Them Please can Ya Help Me but it will not be cheap think of the cost you are goin to do too it

Nov 28, 2013 | 2000 Ford Windstar

1 Answer

1995 s10 4x4 truck runs rough at mid speeds

Are you getting any codes on it? There is two things you might want to change. The first is ya coil and then try it to see if that helps, if not then it could be ya pickup coil in the distrib. And another one is ya map sensor may not be reading air intake right.

Dec 01, 2012 | Chevrolet Cars & Trucks

1 Answer

My 2.5 v6 1999 cougar is difficult to start when cold.

Try the engine temp sensor! I had a renault 3.0 v6 24v in which ford used to use in the old monsters like ya granadas n so on. Its should be on ya cylinder head somewhere and the plug should be green in colour. If ya find it, start up ya engine n pop ya bonnet. Remove the plug, the engine will run smooth strait away. If this is the case, as a temp solution spray with WD40 to to clean n provide a propper connection. In the long run tho ya will need a new sensor which screws into the cylinder head. This sounds like a big problem but it aint n the new sensor can be found on auction sites n ya will prob be able to pay for it with a single note. Hope this helps. If not try ya points.

Jan 09, 2012 | Cars & Trucks

1 Answer

Horn not activated

Put a meter on the horn jack and press horn switch to see if ya have voltage.

If ya do...bad horn.
If ya don't...check horn fuse.
If fuse is good...unseat and reseat relay.

Hope this helps.

Jul 18, 2011 | Ford Windstar Cars & Trucks

1 Answer


if ya heads are cracked before ya do anything find replacements from a breaker yard.
then remove the heads themselves to see if theres any internal damge to the pistons if not. good once ya have the heads off the car ya need to taake them to a specialist so he can tell you the part numbers you need for replacement heads. he may even have some ya never know.
and then rebuild it i could help step by step to do it but i would need pictures to help talk ya through it

May 16, 2010 | 1998 Ford Taurus

1 Answer

How do you bleed the brakes on a 98 ford escort zx2?

There is NO 1 particular screw.. Theres 4.. One on each wheel cylinder on the rear.. and one on each caliper on the front.. If ya dont know this.. then ya probably need to let a shop do it.. Ya have to start at the fartherest point away from the master cylinder. and work from farther.. to closer.. Its not easy if ya never done it..

Mar 11, 2009 | 1998 Ford Escort

1 Answer

2000 Chevy Blazer won't turn over

Check this out ( and dont laugh even though I know ya want to ) Make sure ya terminals are clean on the Batt .. esp the + Side.. MAke sure its charged.. Then after all that. Get one of ya buddies that ya hate to crawl underneath and tap the starter with a hammer as you turn the key.. If it cranks,, go buy a starter.. Hope this helps.. Thank you

Mar 11, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
1999 Honda Civic Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides