Question about 1996 Honda Civic

Open Question

Hond civic 1.4 96-97 d14a4

Do you know the torque settings in nm for it and wat direction 2 tighten bolts or order they go in

Posted by on

  • Curt Downs May 11, 2010

    which bolts?

×

3 Suggested Answers

  • 8 Answers

SOURCE: What is tightening torque of harmonic bal. bolt 1990 Honda Accord

1990 Honda accord
L4 2156cc 2.2ltr engine
crankshaft pulley bolt
apply engine oil to threads (a few drops)
tighten to 159 ft lbs
please rate my answer as I am new
Thanks,
Chris

Posted on Aug 29, 2009

Testimonial: "Thanks for your answer. 159ft-lbs seems a bit high. I only say this because 1990 Honda Integra 1.8L is 130ft-lbs. Maybe because of bigger engine."

MNfisherman
  • 11896 Answers

SOURCE: how to remove transmission on 97 honda civic dx

remove crossmember, axles, cables, tranny mount bolts (3), tranny to engine of course bolts

Go to autozone.com and register for full free online repair manual

Posted on Sep 11, 2009

  • 122 Answers

SOURCE: what to torque head gasket bolts on on 1996 hoda civic

Make sure the bolts are properly lubricated, the threads and the bolt heads, hand tighten all the bolts, use the crisscross method below starting in the center and working your way outward. tighten to 22 ft lbs tighten to 61 ft lbs
X X X X X 8 6 2 4 10 X X X X X 9 3 1 5 7

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for head 1994 Plymouth acclaim 2.5


  1. Step 1 - tighten all 10 bolts to 22 ft. lbs. (30 Nm).
  2. Step 2 - tighten all 10 bolts to 45 ft. lbs. (61 Nm)
  3. Step 3 - re-tighten all 10 bolts to 45 ft. lbs. (61 Nm)
  4. Torque bolts No. 1 through 6 to 110 ft. lbs. (149 Nm)
  5. Torque bolt No. 7 to 100 ft. lbs. (136 Nm)
  6. Torque bolts No. 8 through 10 to 110 ft. lbs. (149 Nm)
  7. Re-tighten each bolt to its proper torque. Pay special attention to bolt No. 7; it should not be over tightened.

Feb 26, 2015 | Plymouth Cars & Trucks

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

99 Honda civic 1.6 engine torque specs and sequences for cylinder head


Tighten the cylinder head bolts to their final torque specification in two steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts.
  1. Step 1: Tighten each bolt to 22 ft. lbs. (30 Nm).
  2. Step 2: Tighten each bolt to 61 ft. lbs. (85 Nm).

zjlimited_1681.jpg

Fig. Cylinder head bolt loosening sequence - 1.6L (B16A2) engines (click image for zoom)

Hope helps.

Aug 05, 2011 | 1999 Honda Civic

1 Answer

Hi i'm eduardo and i have a '94 nissan pathfinder 4wd...engine 3.0.... i want to know the head torque specifications .


Hi Eduardo:
Check this information (click over pics for zoom)...

zjlimited_1062.jpg

Fig. 20: Exploded view of the cylinder head assembly-VG30E engine


zjlimited_1063.jpg

Fig. 15: Cylinder head loosening sequence-VG30i and VG30E engines


zjlimited_1064.jpg

Fig. 17: Cylinder head torque sequence-VG30i and VG30E engines


Install the cylinder head with a new gasket. Apply clean engine oil to the bolt threads and seats, then install the bolts with washers (beveled edges up) in the correct position. Note that bolts 4, 5, 12 and 13 measure 5.00 in. (127mm), and are longer than the others. The other bolts are 4.17 in. (106mm) long.

Tighten the bolts in the proper sequence, in the following stages:
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 43 ft. lbs. (59 Nm).
Loosen all bolts completely.
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 40-47 ft. lbs. (54-64 Nm). Or, if you have an angle torque wrench available, tighten them an additional 60-65 degrees.


Hope this helps; remember to rate this answer. Good luck.

Apr 22, 2011 | Nissan Pathfinder Cars & Trucks

1 Answer

Hi i was wanting to now if anyone knows the Torque Settings for the head of a 1992 Toyota Windom V6. Thank you.


Cylinder Head Torque Sequence

Tightening torque:
12 sided bolt
Step 1 ..... 34 Nm (25 ft lb)
Step 2 ..... Tighten an additional 90°
Step 3 ..... Tighten an additional 90°
Recessed head bolt ..... 18 Nm (13 ft lb)

02e7fe1.gif

f910c49.gif

Oct 21, 2010 | Toyota Passenger Cars & Trucks

1 Answer

Torque para cabeza honda civic motor 1.6


1996-97 Civic and Civic del Sol
1.6L (D16Y5, D16Y7 and D16Y8) ENGINES

Tighten the cylinder head bolts to their final torque specification in four steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows:
  1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
  2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
  3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
  4. Step 4: Retighten only the two center bolts to 49 ft. lbs. (67 Nm).

Hope helps (remember to rate and comment this).

Sep 23, 2010 | 1997 Honda Civic

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Head bolt tighting sequance for a jeep 4.0


CAUTION: During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT overtighten bolt No.11.

  • Tighten all bolts in sequence (1 through 14) to 30 Nm (22 ft. lbs.) torque.
  • Tighten all bolts in sequence (1 through 14) to 61 Nm (45 ft. lbs.) torque.
  • Check all bolts to verify they are set to 61 Nm (45 ft. lbs.) torque.
  • Tighten bolts in sequence:
  • Bolts l through 10 to 149 Nm (110 ft. lbs.) torque.
  • Bolt 11 to 13 Nm (100 ft. lbs.) torque.
  • Bolts 12 through 14 to 149 Nm (110 ft. lbs.) .
  • 21e690f.gif

Apr 21, 2010 | 1998 Jeep Cherokee

1 Answer

Hi what is the head torque on a 2002 honda civic


Dont forget to apply clean engine oil to the threads of each bolt for proper torquing. Then finger tighten. Then

    1. Tighten the cylinder head bolts to their final torque specification in 4 steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows: Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).
    1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
    2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
    3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
    4. Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).


  • Mar 25, 2010 | 2002 Honda Civic

    1 Answer

    2000 2.0 petrol pt cruiser head bolt torque?


    Use a torque wrench to tighten the bolts in the following order:
    1. Tighten all center bolts to 34 Nm (25 ft.-lbs.).
    2. Tighten the four corner bolts to 27 Nm (20 ft.-lbs.).
    3. Tighten all center bolts to 68 Nm (50 ft.-lbs.).
    4. Tighten the four corner bolts to 47 Nm (35 ft.-lbs.).
    5. Retighten all bolts a second time to the same specifications in step 4 to double-check torque.
    6. Finish by tightening all bolts an additional 1/4 turn.

    Nov 11, 2009 | 2001 Chrysler PT Cruiser

    Not finding what you are looking for?
    1996 Honda Civic Logo

    Related Topics:

    100 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...