Question about 1993 Ford F350

1 Answer

No start I've been driving this truck for a while and now it does not start at all. It just turns over. Is their a camshaft position sensor on this year?(Early 1994 non-turbo) Thanks in advance for your help.

Posted by on

  • dan May 11, 2010

    are you getting fuel. sounds like it might be the fuel pump.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,608 Answers

Im gonna assume it's a IDI diesel (you don't say)but that year should
to see if it's gettin fuel try loosning one or two of the injector feed lines (on top of injectors) with a 15mm tube wrench and crank a few times
you should see wet fuel gush out
if not troubleshoot fuel system
if you got fuel you got internal problems(valves)

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My son's friends car died and they pushed in to my house. It cranks, seems week, no start, get a spark through the coils (2), the fuel pump turns on, the battery holds 12.5-12.6 volts and doesn't dro


- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
It could be any of these if this is helpful please leave good feedback
Read more: http://engine-codes.com/p0340_ford.html#ixzz3EIFAq2Gh

Sep 24, 2014 | 2002 Kia Spectra

1 Answer

I have mercedes slk 230 and a code 391 keeps coming up and it stalls while driving sometimes can anybody tell me what it is? please?


Camshaft position sensor B bank 2 CKT range / performance.
Faulty Camshaft Position Sensor
Camshaft Position Sensor harness is open or shorted
Camshaft Position Sensor circuit poor electrical connection
Faulty starter motor
Starting system circuit
Dead (Weak) battery
Any of these could cause this fault code.

Aug 03, 2014 | Cars & Trucks

1 Answer

Temp sensor


I'm not a 100% but it sounds like your camshaft position sensor went bad then caused the other codes to come up because the camshaft position sensor tells the computer how much gas it needs. So it started a chain reaction with the fuel level sensor, fuel temperature sensor, and knock sensor codes. The Fuel temp. sensor helps the engine to know how much fuel to inject as well depending on the temp. of the fuel. The fuel pressure sensor senses the amount of fuel in the fuel rail by reading the internal pressure of the rail, so that's what leads me to believe that it's your camshaft position sensor. Particularly if that was the first code that came up. Hope this helps you.

Aug 27, 2013 | Nissan Xterra Cars & Trucks

1 Answer

Camshaft position sensor correlation bank 1 code


timing belt is off by a tooth or two. you probably didn\'t have to replace the coolant sensor; that code sets whenever the sensor is disconnected and the ignition is turned on; and it needs to be reset by disconnecting the battery or with a code reader. anyway, the crank/ cam sensors are out of sync. if you\'ve got the twin cam engine, they are a royal pain to get the belt to lay properly on the two cams.

Apr 15, 2013 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

1996 Chrysler Concorde: Engine turns over, but will not start.


I think you have to replace the O2 sensors in the exhaust system. this just my guess. you can check from repair shop and then fix it

Aug 16, 2012 | Chrysler Concorde Cars & Trucks

2 Answers

Ml350 replaced a/b cam position sensor reset computer & and erra codes p0016/p0016 check engine ligth is reset car drives with light off when engine is turn off and started the light goes out if you...


P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

Nov 02, 2010 | Mercedes-Benz ML350 Cars & Trucks

2 Answers

Toyota ipsum 2002 check light comes on with code P1346.


Definition of Diagnostic Trouble Code P1346 Audi: Ignition Coil Power Output Stage 3 Short to B+ BMW: Misfire During Start Cylinder 3 Buick: Intake Camshaft Position [CMP] Sensor System Performance Cadillac: Intake Camshaft Position [CMP] Sensor System Performance Chevrolet: Intake Camshaft Position [CMP] Sensor System Performance Ford: Fuel Level Sensor B Circuit GMC: Intake Camshaft Position [CMP] Sensor System Performance Lexus: VVT Sensor Rang/Performance Problem (Bank 1) Lincoln: Fuel Level Sensor B Circuit Mazda: Fuel Level Sensor B Circuit Mercury: Fuel Level Sensor B Circuit Oldsmobile: Intake Camshaft Position [CMP] Sensor System Performance Pontiac: Intake Camshaft Position [CMP] Sensor System Performance Saturn: Intake Camshaft Position [CMP] Sensor System Performance Toyota: VVT Sensor /Camshaft Position Sensor Circuit Range/ Performance Problem (Bank 1) Volkswagen: Ignition Coil Power Output Stage 3 Short to B+

Mar 12, 2010 | 2001 Toyota Sienna

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
1993 Ford F350 Logo

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...