Question about 2002 Buick Century

1 Answer

Rear window will not stay up

My rt. rear window will not stay up. I have to manually raise the window and wedge it in the up position.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 333 Answers

You fist have to take the rear door panel off to see if the window fell of the track. If it has electric windows determine if the moto is running.

Posted on Nov 26, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there a fuse for the window switch

Which window switch ? RT DOOR CB-circuit breaker , do you know what a circuit breaker is ? 25A (System power for right rear window)
LT DOOR CB 25A (System power for left rear window
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

The power window system consists of the following components:
Driver door module (DDM)

Passenger door module (PDM)

Body control module (BCM)

LR power window switch

RR power window switch

Window up and window down relays in each of the rear passenger window switches

Window lockout switch

Reversible power window motors in each of the doors (circuit breaker protected)

LT DOOR CB 25A (System power for left rear window)

RT DOOR CB 25A (System power for right rear window)

If you not sure about any of this I suggest you take your vehicle to a ASE certified repair shop .

Oct 08, 2015 | 2002 Chevrolet TrailBlazer

1 Answer

How do I raise up window manually when power window motor is not working?

take off interior doorpanel and try to manualy push window up a spray of lubricant in the window runners may help ,if window wont move you will have to cut the wire that goes through motor , you will have to renew the motor assembly any way , push window up and wedge each side at bottom of window inside car until you can get new window motor assembly

Mar 25, 2014 | 2002 Chevrolet Cavalier Coupe

1 Answer

Trying to replace a power window motor on an 03 maxima but can't get motor assembly out from behind door and now window is off track as well. Need to know how to get window back in track. Do I need to...

The window need to be lowered to get to bolts that hold it to regulator,then pull glass all the way up and wedge it there,next is to remove all the bolts securing the regulator to door,now work regulator out and replace the motor, with regulator out remove the wedge tilt glass until you are able to get it on the front and rear track ,on track now pull window back up and wedge it.install regulator and bolt it up to door,move regulator with switch to line up bolts to attach glass, now lower glass onto regulator arms and tighten, hope this helps.

Sep 12, 2010 | 2004 Nissan Maxima

1 Answer

Window motor and regulator replacement

  1. Remove the door trim panel and the inner panel water deflector.
  2. Raise or lower the window, as applicable, to the half-up position. CAUTION
    Make sure to properly support the window. If the window drops into the door personal injury or window damage may result.
  3. Support the window in the position needed to access the rivets by inserting rubber wedge door stops at the front and rear of the window between the window and inner door panel. Fig. 1: Support the window with rubber wedges in the door channel 88140g46.gif

  4. Use a 1⁄4 in. (6mm) bit to drill out the attaching rivets on the sash channel. Fig. 2: Location of the window retaining rivets 88140g47.gif

  5. Carefully raise the glass to remove from the sash channel, then remove the glass from the door.
  6. Inspect the bushings, retainers, up stop, pins and wedges on the window for damage.
  7. If necessary, remove the bushings and retainers using a prytool covered with cloth body tape.
  8. If necessary, remove the following:
    1. Window front up stop bolt/screw.
    2. Up stop, nut and washer.
    3. Window stabilizer bolts/screws.
    4. Stabilizer pins, nuts and wedges. Fig. 3: Exploded view of the window glass and related components 88140g48.gif
      To install:
  9. If removed, install the window wedges and stabilizer pins.
  10. If removed, install the stabilizer pin bolts/screws and tighten to 62 inch lbs. (7 Nm).
  11. Install the stabilizer pin nut, if removed and tighten to 71 inch lbs. (8 Nm).
  12. If removed, install the up stop and washer.
  13. If removed, install the up stop bolt/screw and nut. Tighten the bolt/screw to 62 inch lbs. (7 Nm) and the nut to 71 inch lbs. (8 Nm).
  14. If removed, install the bushings and retainers.
  15. Carefully position the window into the door so the holes in the bushings lines up with the holes in the channel.
  16. Install the rivets in sequence.
  17. If necessary, adjust the window as outlined later in this section.
  18. Install the water deflector and trim panel.
  19. Remove the drilled out rivets and shavings from the door.
  20. Check the rivet bushings and retainers on the glass for damage. If necessary, remove the bushings using a flat-bladed tool covered with a cloth body tape. Install by snapping the rivet retainer into the bushing.
  21. Lower the glass into the door and position on the sash channel so the holes in the sash line up with the holes in the bushings and retainers.
  22. Using rivet tool J–29022 or equivalent, install 1⁄4 in. (6mm) peel type rivet (part No. 20184399 or equivalent) to retain the glass to sash channel.
  23. Install the rear guide channel.
  24. Install the front up stop to support on the inner panel.
  25. Before installing the trim parts, check the window operation for performance and fit to roof rail weatherstrip.
  26. Install the inner panel water deflector and the door trim panel.
prev.gif next.gif

Jul 08, 2010 | 1997 Chevrolet Camaro

5 Answers

2002 jeep liberty interior fuse diagram

1-20amp-pwr outlet frt. 2-10amp-rear fog lights(export only)
3-15 amp-horn 4-10amp-hedlt low beam rt
5-10amp-hedlt low beam lft 6-20amp-bodycontrolmodule/pwr dr locks 7-spare 8-spare 9-10amp- rt pk lt /rt tail lt/trailer tow lt/cluster
10-spare 11-15 amp-flasher 12-15 amp-stop lts
13-10amp-bodycontrolmodule/cmtc/cluster 14-spare
15-10amp-pdc fuel pmp & auto shutdownrelays/skis
16-20amp-pwr outlet rear 17-15amp-rear wiper 18-20amp-radio choke relay 19-20amp-frt fog lts/trailer tow stop and turn lts
20-20amp-sunroof 21-spare 22-10amp-wiperswitch/frt and rear washer 23-10amp-lft park lt/lft tail lt 24-10amp-pdc blower motor relay 25-10amp-heatseatswitch/hvac controlhead/trailor tow battery charge 26-10amp-hedlt highbeam rt 27-10amp-hedlt highbeam lft
28-spare 29-15amp-heated seat module 30-10amp-heated mirrors/rearwindowdefrosterindicator 31-20amp-cigarlighter
33-10amp-skis/diagnostic connector 34-15amp-cluster/courtesy lts/radio/bodycontrolmodule/maplights/cmtc/underhood lt/vanity lts
35-spare 36-10amp-ignition run/start-orc/lft and rt siacm
37-10amp-ignition run only-orc 38-10amp-abs module/brake shift interlock solenoid 39-10amp-rear window defroster relay/flasher/backup lts

Jul 03, 2009 | 2002 Jeep Liberty

1 Answer

Electric Window on a 1999 monte carlo is in the down position and wedged in the bottom of the door. Window motor drove window down but will not drive upward. Can I drill off the 3 rivets holding the motor...

can you place a thin screwdriver down through the top of door, between the DOOR GLASS and OUTER door panel. If you can, try to raise glss electrically SLOWLY guiding it past the the binding edge. Door glass will need alignment to perrmantly repair

Apr 05, 2009 | 1999 Chevrolet Monte Carlo

1 Answer

1995 olds cierra

don't cut the wires just unplug the motor only not the switch

Mar 25, 2017 | 1995 Oldsmobile Cutlass Supreme

1 Answer

1995 olds cierra

you can disconect the plug from window motor and the rest of the windows will still work... you can cut the wires if you want to but tape the ends so they dont short out or you will have other problems..

Nov 17, 2008 | 1995 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2002 Buick Century Logo

Related Topics:

502 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides